Hello All,

Could someone lease help.  How do you turn off or turn the courtesy tones down. This is what I have in rpt.conf  Under [telemetry]

[telemetry]

; Telemetry entries can be shared across all repeaters, or defined for each repeater.

; Can be a tone sequence, morse string, or a file

;

; |t - Tone escape sequence

;

; Tone sequences consist of 1 or more 4-tuple entries (freq1, freq2, duration, amplitude)

; Single frequencies are created by setting freq1 or freq2 to zero.

;

; |m - Morse escape sequence

;

; Sends Morse code at the telemetry amplitude and telemetry frequency as defined in the

; [morse] section.

;

; Follow with an alphanumeric string

;

; |i - Morse ID escape sequence

;

; Sends Morse code at the ID amplitude and ID frequency as defined in the

; [morse] section.

;

; Follow with an alphanumeric string

telemdefault=2;;0=telemetry output off, 1 = telemetry output on, 2 = timed telemetry output on command execution and for a short time thereafter  1

telemdynamic=1;;0=disallow users to change the local telemetry setting with a COP command, 1 = Allow users to change the setting with a COP command  1

guilinkdefault=0;0= telemetry output off, 1 = telemetry output on, 2 = timed telemetry output on command execution and for a short time thereafter, 3 = follow local telemetry mode  1

guilinkdynamic=0;0= disallow users to change the gui telemetry setting with a COP command, 1 = Allow users to change the setting with a COP command  1

phonelinkdefault=0;0= telemetry output off, 1 = telemetry output on, 2 = timed telemetry output on command execution and for a short time thereafter, 3 = follow local telemetry mode  1

phonelinkdynamic=0;0= disallow users to change phone telemetry setting with a COP command, 1 = Allow users to change the setting with a COP command  1

eannmode=0; 0=do not announce Echolink nodes at all, 1 = announce only the node number (Allstar-translated), 2 = announce only the call of the echolink station, 3 = announce both  1

echolinkdefault=2; 0= telemetry output off, 1 = telemetry output on, 2 = timed telemetry output on command execution and for a short time thereafter, 3 = follow local telemetry mode  2

echolinkdynamic=0; 0= disallow users to change current echolink telemetry setting with a COP command, 1 = Allow users to change the setting with a COP command  1

ct1=|t(350,0,100,1000)(500,0,100,1000)(660,0,100,1000)

ct2=|t(660,880,150,0) 

ct3=|t(440,0,150,0)

ct4=|t(550,0,150,1000)

ct5=|t(660,0,150,1000)

ct6=|t(880,0,150,1000)

ct7=|t(660,440,150,1000)

ct8=|t(700,1100,150,0)

remotetx=|t(1633,0,50,1000)(0,0,80,0)(1209,0,50,1000);

remotemon=|t(1209,0,50,1000)

cmdmode=|t(900,903,200,1000)

functcomplete=|t(1000,0,100,1000)(0,0,100,0)(1000,0,100,1000)

patchup=rpt/callproceeding

patchdown=rpt/callterminated

CT 2,3,8 I turned down amplitude to 0 but still have tones . Can someone tell me what I’m doing wrong.

73

Harry Romano

KC4RPP

Skype: hromano777

Phone 1-239-455-1411