Yes, If you changed things in a .c file it would have to be recompiled to take advantage of it. The source is in /usr/src/astsrc/

Compiling is easy. Just make sure you make backups of the file(s) you change so you can go back if there is a problem.

Make the change(s) Then issue these commands....

make clean
./configure
make
make install

It takes about 10 minutes to a half hour or more depending on the speed of your system.

Also understand that when you make changes and later do an update they will go away but usually there is no reason to do an update unless there is some fix you really need.

73 Doug
WA3DSP
http://www.crompton.com/hamradio

Date: Sun, 23 Mar 2014 11:56:48 -0700
From: n6gkj.cm98@yahoo.com
To: app_rpt-users@ohnosec.org
Subject: Re: [App_rpt-users] USB FOB options

This custom code required recompiling?

From: Doug Crompton <doug@crompton.com>;
To: app_rpt-users@ohnosec.org <app_rpt-users@ohnosec.org>;
Subject: Re: [App_rpt-users] USB FOB options
Sent: Sun, Mar 23, 2014 4:59:03 PM

If there are some other than standard bits that are available on these encased FOBs and you can identify what they are it can be customized in the SW.

else if(o->hdwtype==3) // custom version
        {
                o->hid_gpio_ctl         = 0x0c;        /* set GPIO 3 & 4 to output mode */
                o->hid_gpio_ctl_loc     = 2;   /* For CTL of GPIO */
                o->hid_io_cor           = 2;   /* VOLD DN is COR */
                o->hid_io_cor_loc       = 0;   /* VOL DN COR */
                o->hid_io_ctcss         = 2;   /* GPIO 2 is External CTCSS */
                o->hid_io_ctcss_loc = 1;       /* is GPIO 2 */
                o->hid_io_ptt           = 4;   /* GPIO 3 is PTT */
                o->hid_gpio_loc         = 1;   /* For ALL GPIO */
                o->valid_gpios          = 1;   /* for GPIO 1 */
        }

73 Doug
WA3DSP
http://www.crompton.com/hamradio

Date: Sat, 22 Mar 2014 13:41:36 -0700
From: n6gkj.cm98@yahoo.com
To: app_rpt-users@ohnosec.org
Subject: Re: [App_rpt-users] USB FOB options

I have a box of those, none of the buttons function with Allstar. They are great for how I use them.
I use the 2nd audio channel to send pl tone, the rectify and filter that to drive a transistor for PTT.
COR is done via Allstar DSP.

Sent from Yahoo Mail on Android

From: Eric Guth <eric@efratnetworks.com>;
To: app_rpt-users@ohnosec.org <app_rpt-users@ohnosec.org>;
Subject: Re: [App_rpt-users] USB FOB options
Sent: Sat, Mar 22, 2014 6:54:18 PM

I just received 8 of the "blob fobs" for $.99 each. Is there anyone working on assigning the PTT to one of the LEDs on the fob?

73,

Eric

4Z1UG / WA6IGR

Allstar Node: 28422

From: app_rpt-users-bounces@ohnosec.org [mailto:app_rpt-users-bounces@ohnosec.org] On Behalf Of Steve Wright
Sent: Saturday, March 08, 2014 5:32 AM
To: app_rpt-users@ohnosec.org
Subject: Re: [App_rpt-users] USB FOB options

Ok I can confirm that de-blobbing this CM119 chip is a no-go. Heat gun removed the blob no worries, but removed (or destroyed) everything else as well. Might be a good option if you wanted to desolder the entire board which it did famously, but removing the blob also removed the chip and after that of course the computer wouldn't recognise the device. $3.50 down the flusher, oh well!

Steve

Meshnetworks - Rangitaiki Plains Rural Broadband Internet Providers

+64 21 040 5067

_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.