I suggest you cd to the zaptel directory and run ./configure <br>Pay close attention to the output and look for dependencies that might be missing.  When you satisfy those, then see if it compiles cleanly.<br><br>Also, I haven&#39;t used Sabayon Linux before.  It&#39;s Gentoo based right?  Make sure you have all of the required build tools (which you should with gentoo), there might be one of the tools you are missing.<br>
<br>73&#39;s<br>Mark - WL7NI<br><br><br><div class="gmail_quote">On Mon, Oct 31, 2011 at 2:11 PM, Ken Page <span dir="ltr">&lt;<a href="mailto:vk4akp@yahoo.com.au">vk4akp@yahoo.com.au</a>&gt;</span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex;">

  
    
  
  <div bgcolor="#FFFFFF" text="#000000">
    OK,<br>
    <br>
    I finally got a chance to have a go at this. <br>
    <br>
    But it crashed at the Zaptel stuff.<br>
    <br>
    --<br>
    make[1]: Entering directory `/usr/src/asterisk/trunk/zaptel&#39;<br>
    make -C /lib/modules/2.6.25-sabayon-r1/build ARCH=i386
    SUBDIRS=/usr/src/asterisk/trunk/zaptel/kernel HOTPLUG_FIRMWARE=yes
    KBUILD_OBJ_M=&quot;pciradio.o wcfxo.o wct1xxp.o wctdm.o wcte11xp.o
    zaptel.o ztd-eth.o ztd-loc.o ztdummy.o ztdynamic.o zttranscode.o
    wctdm24xxp/&quot; modules<br>
    make[2]: Entering directory `/usr/src/linux-2.6.25-sabayon-r1&#39;<br>
    Makefile:1522: *** mixed implicit and normal rules.  Stop.<br>
    make[2]: Leaving directory `/usr/src/linux-2.6.25-sabayon-r1&#39;<br>
    make[1]: *** [modules] Error 2<br>
    make[1]: Leaving directory `/usr/src/asterisk/trunk/zaptel&#39;<br>
    make: *** [all] Error 2<br>
    make: Leaving directory `/usr/src/asterisk/trunk/zaptel&#39;<br>
    make: *** [llastate/zaptel-built] Error 2<br><font color="#888888">
    <br>
    --<br>
    <br>
    ~Ken - vk4akp<br>
    .-.-.</font><div><div></div><div class="h5"><br>
    <br>
    <br>
    On 10/28/2011 8:27 AM, Mark Huelskoetter wrote:
    <blockquote type="cite">Are you running 3 nodes on this server or just two? 
      Because your lsusb output suggests that you are running  3 URI&#39;s. 
      If that&#39;s the case asterisk might be getting confused on which usb
      device is which.  Before you go through the hassle of recompiling
      everything try unplugging all of the radio interfaces, run
      asterisk and look for the segfault.  Next, add one back, restart
      asterisk and see what happens, etc...You see where I am going with
      this?  Try them all, maybe even in different ports.  If you are
      still having problems, download the new sources and compile.<br>
      <br>
      I suggest you back up of the .conf files in /etc/asterisk, then
      obtain the new source code.  Per the instructions on the Allstar
      webpage, you can get it in the following fashion:<br>
      <br>
      cd /usr/src/<span style="font-weight:normal"><br>
        wget <a href="http://x.allstarlink.org/svn-trunk.tar.gz" target="_blank">http://x.allstarlink.org/svn-trunk.tar.gz</a>
        -O- | tar xz</span>v<br>
      mv trunk astsrc<br>
      cd astsrc<br>
      <br>
      Then you can use the make command.  I think make install_usbradio
      is correct for your situation, I am not where I can check my
      notes.  Someone else might be able to suggest something different.<br>
      <br>
      Good LUCK!!!<br>
      <br>
      Mark - WL7NI<br>
      <br>
      <br>
    </blockquote>
  </div></div></div>

</blockquote></div><br>