Yeah this pi is remote, I’m gonna look in the rpi-update commits too and see what I can find, I was able to build the modules in a custom kernel but am missing some pre-load dependencies of course lol

Sent from the iRoad

On Jul 12, 2018, at 04:31, Steve Zingman <szingman@msgstor.com> wrote:

I have not tried this myself yet but here are the last kernel and matching header. I would try to install the kernel and then the headers.
<https://archive.raspberrypi.org/debian/pool/main/r/raspberrypi-firmware/raspberrypi-kernel_1.20171029-1_armhf.deb>
<https://archive.raspberrypi.org/debian/pool/main/r/raspberrypi-firmware/raspberrypi-kernel-headers_1.20171029-1_armhf.deb>

If it boots after this, put the kernel and headers on hold.

I'll play with this myself when I get a chance

73, Steve N4IRS

On 07/11/2018 06:48 PM, JJC wrote:
I haven't made osspd work yet, I'm gonna try padsp next lol... 

Otherwise I need to find a kernel that still has the old OSS modules.. or just build one as I had said before and mark broken as allowed... though I really don't wanna do that if I can avoid it...

JJC

On Tue, Jul 10, 2018 at 1:31 PM Steve Zingman <szingman@msgstor.com> wrote:
If I had to guess, I would say a bad SD card burn. or a bad card.

Steve N4IRS

On 7/10/2018 11:20 AM, Jim Aspinwall No1PC wrote:
Coincidence? Serendipity?

I just tried the latest builds from: http://dvswitch.org/files/ASL_Images/Raspberry_Pi/Stretch/ 

Liking asl-menu... that helps... but as with others below... I have found, on a Pi3 + RA-40 that works under the prior 'build' - I too am experiencing multiple errors and ultimately failure of asterisk app to identify, connect to and use the USB-connected RA-40 as either USBRadio or SimpleUSB that worked under same configuration parameters. It's even complaining that asterisk.ctl is not in /var/run when it clearly is there.

On the console I am getting low voltage errors I never saw before... using the same power source. Measurement at the board is minimum 4.96v.  Power source is a PowerPole USBBuddy 3A device from clean DC - these run all of my field-racked nodes so far.  Even a 1.5a wall-wart has been fine prior.  Doesn't make sense when the operational voltage tolerance of the Pi is greater than this 0.8% difference.  If the low-voltage check is getting in the way... how do we fix that?    Separate power sources for Pi vs interface boards?

If the voltage issue is NOT "getting in the way" of Asterisk using a good known USB-interfaced device? What is?  

Again, I can shut down the boards, swap the USB Flash drive from the latest build to the prior and it runs fine.  I'm reluctant to in-place update the working node/stick... until I can properly clone the stick and test on an expendable build.   (What tool does one use to make an image from a bootable stick?)


 Yeah it's decidedly an issue with snd-pcm-oss missing from the system..
> may need to compile a custom kernel.. _shrug_


>> this may not be relevant, but worth saying at this point.
>>
>> I have found that if you initialize a pi node while not supplying the Pi
>> board with enough current
>>
>> during the initial start-up. Many things seem to go wrong.
>>
>> I'm building a bigger 5v power supply to handle 2 or three of these at
>> once to verify what I'm thinking,
>>
>> but not tested anything yet.
>>
>> In my case, it is Dahdi
>>> Not sure why but the /dev/dsp1 seems to be missing... I've installed
>>> oss-compat and tried a number of things.. see below output...
>>>
>>> $ sudo uridiag
>>> URIDiag, diagnostic program for the DMK Engineering URI
>>> USB Radio Interface, version 0.9, 08/14/15
>>>
>>> Found CM119 USB Radio Interface at 001/005
>>> Unable to re-open DSP device 1: /dev/dsp1
>>>



_______________________________________________
App_rpt-users mailing list
App_rpt-users@lists.allstarlink.org
http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users

To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.

_______________________________________________
App_rpt-users mailing list
App_rpt-users@lists.allstarlink.org
http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users

To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. 


_______________________________________________
App_rpt-users mailing list
App_rpt-users@lists.allstarlink.org
http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users

To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.

_______________________________________________
App_rpt-users mailing list
App_rpt-users@lists.allstarlink.org
http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users

To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.