Plug in your URI, RIM, or usb sound device and you will see it pop up on the linux screen

as [root@~]  radio-tune-menu 

the radio tune menu will allow you to setup your sound devices provided your .conf files are correct

ACID is a repeater controller if you have 2 URIs or RIMs  you can bridge your IRLP node  

beside IRLP configured on an ACID install had some audio level issues. Not sure about

Xipar but it also had configs for IRLP.  I only tested it on ACID

p.s. Scott I noticed you seen the publicizing for the RIM

JK   

From: Richard Szajkowski <va3rzs@gmail.com>
To: Johnny Keeker <cypresstower@yahoo.com>
Cc: App_rpt Users <app_rpt-users@ohnosec.org>
Sent: Friday, October 11, 2013 1:06 PM
Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20

How will I know if it works after I plug it in ? Is there a script that I need to run it install it 

I am finding the docs out of date or not there at all (some links are dead like for the 4 port card)

I know IRLP is not supported any more , sad as I run an IRLP node , and would have liked to run all 3 networks on one computer , to save a port for the 220 repeater 

I thank you for all your help , 

Richard Szajkowski

On Oct 11, 2013, at 12:43 PM, Johnny Keeker <cypresstower@yahoo.com> wrote:

I don&apos;t know the device but if it has a CM108 or CM119 chip it will.

Personally, I use startech sound fobs. They&apos;re easily modifiable 

using surface mount components and they&apos;re reliable. URI&apos;s are very

good, but have my eye on the RIM as it has advantages over the URI.
JK

From: Richard Szajkowski <va3rzs@gmail.com>
To: Johnny Keeker <cypresstower@yahoo.com>
Sent: Friday, October 11, 2013 11:42 AM
Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20

Do you know if the signal link USB sound card would work ????  I have ordered a uri , but I was asked if I would host a node for another repeater 

Richard Szajkowski

On Oct 10, 2013, at 8:31 PM, Johnny Keeker <cypresstower@yahoo.com> wrote:

At the least you have success.  It takes about 10 minutes or less, when you first boot

before your node reports to all the other on-line nodes. Some of my nodes

use a static IP and others DHCP with reserved address.  Let us all know how things

work out for you.

Good luck Richard

JK

From: Richard Szajkowski <va3rzs@gmail.com>
To: Johnny Keeker <cypresstower@yahoo.com>
Sent: Thursday, October 10, 2013 7:02 PM
Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20

I now have what I think is a working system , 

For some reason it fails if I put in a static IP , but if I run with DHCP it finds the mic and runs 

If I tell it to pull down the info from the server for he node it dies

I need it on a static IP for port fowarding , just like my other VoIP systems 

And I did do the info on the web portal to the best I can, I entered in all the info it requested 

I even got to install your device now , this will be here Tuesday because of our long weekend 

Thanks for all the help

Richard Szajkowski

On Oct 10, 2013, at 6:31 PM, Johnny Keeker <cypresstower@yahoo.com> wrote:

did you Not Create an installation disk????

I thought you were past that point and sitting at the test prompt

If you completed the ACID install and got the test prompt

the password is &apos;setup&apos;

once your in root type passwd and change it 

nodesetup.sh   will run the script to push your node config files from the allstar server to

your node "provided you created and saved the files prior to your ACID installation"

JK 

From: "zeppelin.1@netzero.com" <zeppelin.1@netzero.com>
To: app_rpt-users@ohnosec.org
Sent: Thursday, October 10, 2013 5:20 PM
Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20

Hello Richard and welcome to the Linux world;
                                                                  You "must" do a CD BURN to the ISO for it to work properly, low speed is best for older CD ROM.

73 Anton/ KC2RQR
Node 29103

---------- Original Message ----------
From: app_rpt-users-request@ohnosec.org
To: app_rpt-users@ohnosec.org
Subject: App_rpt-users Digest, Vol 56, Issue 20
Date: Thu, 10 Oct 2013 12:00:01 -0400

Send App_rpt-users mailing list submissions to
app_rpt-users@ohnosec.org

To subscribe or unsubscribe via the World Wide Web, visit
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
or, via email, send a message with subject or body &apos;help&apos; to
app_rpt-users-request@ohnosec.org

You can reach the person managing the list at
app_rpt-users-owner@ohnosec.org

When replying, please edit your Subject line so it is more specific
than "Re: Contents of App_rpt-users digest..."


Today&apos;s Topics:

  1. Help with new install (Richard Szajkowski)


----------------------------------------------------------------------

Message: 1
Date: Wed, 9 Oct 2013 18:14:55 -0400
From: Richard Szajkowski <va3rzs@gmail.com>
To: "app_rpt-users@ohnosec.org" <app_rpt-users@ohnosec.org>
Subject: [App_rpt-users] Help with new install
Message-ID: <B2A7C8C9-28C3-4A33-8F56-558F97D69D7D@gmail.com>
Content-Type: text/plain; charset=us-ascii

Hello to the group

I am trying to get the computer on line while my interface is shipped

I downloaded the ISO off the website , followed the prompts , I am not at a prompt
Test >

I did not enter a root password as I was not asked

I can&apos;t find a PDF or anything on 1st time installs

Any help would be great

Thanks

Richard Szajkowski va3rzs



------------------------------

_______________________________________________
App_rpt-users mailing list
App_rpt-users@ohnosec.org
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users


End of App_rpt-users Digest, Vol 56, Issue 20
*********************************************

____________________________________________________________
NetZero now offers 4G mobile broadband. Sign up now.

_______________________________________________
App_rpt-users mailing list
App_rpt-users@ohnosec.org
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users

_______________________________________________
App_rpt-users mailing list
App_rpt-users@ohnosec.org
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users