Joe:
I've done this, it is working great in testing. Here are the
parts ...
1) APP_RPT doesn't support all PL tones (ACID Distribution) ... I
believe that this is the valid decode list (any PL can be
transmitted) ...
| PL | NOTES |
| 67.0 | |
| 69.3 | Not Available in AllStar RX DSP |
| 69.4 | Not Available in AllStar RX DSP |
| 71.9 | |
| 74.4 | |
| 77.0 | |
| 79.7 | |
| 82.5 | |
| 85.4 | |
| 88.5 | |
| 91.5 | |
| 94.8 | |
| 97.4 | |
| 100.0 | |
| 103.5 | |
| 107.2 | |
| 110.9 | |
| 114.8 | |
| 118.8 | DO NOT USE - 60 Hz Harmonic |
| 123.0 | |
| 127.3 | |
| 131.8 | DO NOT USE - DCS Turn Off Code |
| 136.5 | DO
NOT USE - DCS Turn Off Code |
| 141.3 | |
| 146.2 | |
| 151.4 | |
| 156.7 | |
| 159.8 | Not Available in AllStar RX DSP |
| 162.2 | |
| 165.5 | Not Available in AllStar RX DSP |
| 167.9 | |
| 171.3 | Not Available in AllStar RX DSP |
| 173.8 | |
| 177.3 | Not Available in AllStar RX DSP |
| 179.9 | DO NOT USE - 60 Hz harmonic |
| 183.5 | Not Available in AllStar RX DSP |
| 186.2 | |
| 189.9 | Not Available in AllStar RX DSP |
| 192.8 | |
| 196.6 | Not Available in AllStar RX DSP |
| 199.5 | Not Available in AllStar RX DSP |
| 203.5 | |
| 206.5 | Not Available in AllStar RX DSP |
| 210.7 | |
| 218.1 | |
| 225.7 | |
| 229.1 | Not Available in AllStar RX DSP |
| 233.6 | |
| 241.8 | |
| 250.3 | |
| 254.1 | Not Available in AllStar RX DSP |
2) The method to associate RX and TX tones and have valid decode
of certain PLs in usbradio.conf is ....
;
; CTCSS / PL TONES
txctcssdefault= 103.5 ; default tx ctcss freq, any frequency
permitted, used when RX is quiet
rxctcssfreqs= 67.0,88.5,103.5,136.5,192.8,250.3
; rx ctcss freqs in floating point. must
be in table
txctcssfreqs= 67.0,88.5,103.5,103.5,192.8,250.3
; tx ctcss freqs, any frequency permitted
;
; RECEIVER CONTROLS
;
rxctcssoverride=0 ; Set to 1 or yes to start out in carrier
squelch mode
rxctcssrelax=0 ; reduce talkoff from radios w/o CTCSS Tx
HPF
; ; (help radios with DTMF Twist)
** Note, you can cross PLs ... when the above receives 136.5 it transmits 103.5
Like I said, so far it has all worked ... just feed voice and PL from the discriminator to the AllStar server. Good Luck!
...STeve - KF5VH
Thanks in advance!I have a need to setup a community repeater. This is done easily with a shared repeater tone panel and the like from CSI. I was wondering if this could be accomplished using app_rpt. All it would need to do is allow the use of multiple input and output PL tones. Simply put, when the repeater receives X pl tone it transmits the X pl tone on the output and when the repeater receives Y pl tone it transmits the Y pl tone on the output.If anyone has done this or has any idea on how this would be accomplished it would be much appreciated.
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.