It works FINE!!

You have to send digits to the node that has the propagate_dtmf, and it will output them.

For example, if the node that has that set up is 1234, then you need, once you link to it
from a different node, do a *41234 (into command mode for node 1234), then whatever
digits you send to it will go out the main interface for node 1234.

Jim WB6NIL

Date: Mon, 29 Oct 2012 22:16:34 -0400
From: kb2faf@arrl.net
To: app_rpt-users@ohnosec.org
Subject: Re: [App_rpt-users] Fwd: Dtmf pass through

FYI,

I have the same problem and have tried everything indicated below with no luck. It can't be this complicated can it?

Chris
KB2FAF

On 10/29/2012 04:19 PM, Ian Venable wrote:

So I still am having trouble with this. So far I have added

propagate_dtmf=yes

linktolink=yes
inxlat=#56,#57,0123456789ABCD
outxlat=#56,#57,0123456789ABCD

to the rpt.conf file on the node that has the cat200b controller attached to it. Also on both of my other nodes that are connected via the allstar system i have added

propagate_dtmf=yes

to there rpt.conf files. I have done a restart on all the nodes, and still not getting the dtmf to pass through. When the dtmf passes through you should be able to hear it on the output of the repeaters, right? As long as it is not started with a (*) then the node would try to act on the dtmf. The cat200b controller is in remote base weather mode, and does not require COR, or PL to act, all it is looking at is the Tx audio from the usb fob, which goes into the Rx port on the controller. So all the controller needs to hear is the DTMF audio, but its not getting there. The controllers Tx audio is connected to the Rx audio on the usb fob, and I know thats working because I hear the controller identify itself with its version when I power cycle it. I am probably doing something wrong, so hopefully someone could point me in the right direction. Thanks!

Ian Ki6ies

On Sun, Oct 28, 2012 at 5:42 PM, Ken <ke2n@cs.com> wrote:

*4 sends “telemetry” (control codes) to the other node … not DTMF

I think you want

propagate_dtmf=yes

in the node stanza

Ken

From: app_rpt-users-bounces@ohnosec.org [mailto:app_rpt-users-bounces@ohnosec.org] On Behalf Of ki6ies.tasma@gmail.com
Sent: Sunday, October 28, 2012 5:31 PM
To: app_rpt-users@ohnosec.org
Subject: [App_rpt-users] Fwd: Dtmf pass through

-------- Original Message --------
Subject: Dtmf pass through
From: ki6ies.tasma@gmail.com
To: app_rpt-users-request@ohnosec.org
CC:

Hello all! I need some help. I am trying to control a cat200 repeater controller via dtmf. It is its own node. I have my other node (uhf repeater)connected to it, from which i would like to send the commands from. I have tried the *4 and the node number. And then i hear "By your command". But dtmf is not making it to the controller. It is making it to the other node, because I can issue it commands. It is just not passing through the other node, which i would like for it to do. Any thoughts?

Ian

Sent from my Verizon Wireless 4G LTE DROID
_______________________________________________
App_rpt-users mailing list
App_rpt-users@ohnosec.org
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users

_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users