root@lorentedford:/etc/asterisk# nodesetup

*************************************

*     Simple Node Setup Script      *

*************************************

The system configuration type is the type of hardware and software

running on your system (simpleusb, channel_usb)

WARNING: Modifying the configuration type on an already set-up system

will over-write all existing configuration files!!!

If this is an initial installation, you have nothing to worry about.

Please make sure you understand these consequences if you

choose to change the system configuration type.

Would you like your config files be provided by the Allstar Portal server [Y/n]? y

This requires you to have already applied for and received an approved

Allstar Link Portal user ID, set it up to be a system operator, created

an entry for, and properly configured information about this Server, and

requested, and received an approved Node entry for each of the Nodes on

this Server, and properly configured the inforation for each of the Nodes.

Have you estblished and entered the appropriate information on that server [y/N]? y

*********************************************

*     Allstar Portal Node Setup Script      *

*********************************************

Do you wish to use the pre-configured user information (user kc9zhv) [Y/n]? y

Please select one of the following servers

1)  KC9ZHV Repeater Site

2)  KC9ZHV 2 meter TX

3)  KC9ZHV-DataCenter-HUB

4)  kc9zhv 2m dc

Please make your selection (1-4): 4

Okay to download config for server kc9zhv 2m dc [Y/n]? y

Downloading server kc9zhv 2m dc...

Problem with Centos networking setup!

Allstar Link Portal Config Download Failed.. exiting

root@lorentedford:/etc/asterisk#

root@lorentedford:/etc/asterisk# cat /srv/post_install/nodesetup

# !/bin/bash

#

# nodesetup.sh

#

DRY_RUN=0

PCF_LOCAL=1

CONFIGS=/etc/asterisk

TMP=/tmp

SENABLE=1

function die {

        echo "Fatal error: $1"

        exit 255

}

function promptnum

{

        ANSWER=""

        while [ -z $ANSWER  ] || [[ ! $ANSWER =~ [0-9]{3,}$ ]]

        do

                echo -n "$1: "

                read ANSWER

        done

}

function promptcall

{

        ANSWER=""

        while [ -z $ANSWER  ] || [[ ! $ANSWER =~ [\/,0-9,a-z,A-Z]{3,}$ ]]

        do

                echo -n "$1: "

                read ANSWER

        done

}

function promptyn

{

        echo -n "$1 [y/N]? "

        read ANSWER

        if [ ! -z $ANSWER ]

        then

                if [ $ANSWER = Y ] || [ $ANSWER = y ]

                then

                        ANSWER=Y

                else

                        ANSWER=N

                fi

        else

                ANSWER=N

        fi

}

function promptny

{

        echo -n "$1 [Y/n]? "

        read ANSWER

        if [ ! -z $ANSWER ]

        then

                if [ $ANSWER = N ] || [ $ANSWER = n ]

                then

                        ANSWER=N

                else

                        ANSWER=Y

                fi

        else

                ANSWER=Y

        fi

}

echo "*************************************"

echo "*     Simple Node Setup Script      *"

echo "*************************************"

echo

echo "The system configuration type is the type of hardware and software"

echo "running on your system (simpleusb, channel_usb)"

echo

echo "WARNING: Modifying the configuration type on an already set-up system"

echo "will over-write all existing configuration files!!!"

echo "If this is an initial installation, you have nothing to worry about."

echo

echo "Please make sure you understand these consequences if you"

echo "choose to change the system configuration type."

echo

promptny "Would you like your config files be provided by the Allstar Portal server"

if [ "$ANSWER" = "Y" ]

then

        echo

        echo "This requires you to have already applied for and received an approved"

        echo "Allstar Link Portal user ID, set it up to be a system operator, created"

        echo "an entry for, and properly configured information about this Server, and"

        echo "requested, and received an approved Node entry for each of the Nodes on"

        echo "this Server, and properly configured the inforation for each of the Nodes."

        echo

        promptyn "Have you estblished and entered the appropriate information on that server"

        if [ "$ANSWER" = "Y" ]

        then

                if [ -x /usr/bin/curl ] && [ -e /etc/ssl/certs/ca-certificates.crt ]

                then

                        TMPF=/tmp/pcf.sh

                        /bin/rm $TMPF > /dev/null 2>&1

                        curl -L -s https://allstarlink.org/config/portalconfig.sh -o $TMPF

                        if [ $? -ne 0 ]

                        then

                                echo "curl was not able to download necessary script file, sorry."

                                exit 1

                        fi

                        if [ $PCF_LOCAL -eq 1 ]

                                then

                                        cp /usr/local/sbin/pcf.sh $TMPF

                        fi

                        bash $TMPF

                        if [ $? -ne 0 ]

                        then

                                rm $TMPF

                                echo "Allstar Link Portal Config Download Failed.. exiting"

                                exit 1

                        fi

                        rm $TMPF

                        echo

                        echo "Congradulations! From now on, you will be able to initiate an automatic"

                        echo "download of any Node or Server configuration changes from the Allstar"

                        echo "Portal (just from the Web, without even having to have any sort of terminal"

                        echo "session active to this system)."

                        echo

                        echo "You must now manually re-boot the system for these changes to take place."

                        echo

                        echo "Thank you for using the Allstar Link Network System!"

                        echo

                        exit 0

                else

                        echo "curl and its associated cert file(s) can not be found, sorry!"

                        exit 1

                fi

        else

                echo "Nothing changed!"

                exit 0

        fi

fi

echo

echo "Doing sanity checks on rpt.conf, extensions.conf, iax.conf, and savenode.conf..."

if [ -e $CONFIGS/extensions.conf ]

then

        grep -q -s 'NODE =' $CONFIGS/extensions.conf || die "extensions.conf missing NODE=xxxx"

        NODE=$(grep 'NODE =' /etc/asterisk/extensions.conf | awk -F'= ' '{print $2}' | awk -F' ;' '{print $1}')

        NODE=$(echo $NODE | awk '{$1=$1}1')

else

        die "$CONFIGS/extensions.conf not found"

fi

if [ -e $CONFIGS/rpt.conf ]

then

        grep -q -s $NODE $CONFIGS/rpt.conf || die "Node numbers in rpt.conf and extensions.conf are different!"

else

        die "$CONFIGS/rpt.conf not found"

fi

if [ -e $CONFIGS/iax.conf ]

then

        grep -q -s register\.allstarlink\.org $CONFIGS/iax.conf || die "No allstar link register statement in iax.conf! (old file maybe?)"

        REG1=$(grep 'register =' $CONFIGS/iax.conf | awk -F'=' '{print $2}' | awk -F'   ;' '{print $1}')

        REG=$(echo "$REG1" | awk -F'@' '{print $1}')

        REGNODE=$(echo "$REG" | awk -F':' '{print $1}')

        REGPSWD=$(echo "$REG" | awk -F':' '{print $2}')

        if [ $REGNODE != $NODE ]

        then

                die "Node numbers in rpt.conf and iax.conf are different!"

        fi

else

        die "$CONFIGS/iax.conf not found"

fi

if [ -e $CONFIGS/savenode.conf ]

then

        grep -q -s NODE= $CONFIGS/savenode.conf || die "savenode.conf missing NODE=xxxx"

        grep -q -s PASSWORD= $CONFIGS/savenode.conf || die "savenode.conf missing PASSWORD=xxxx"

        grep -q -s ENABLE= $CONFIGS/savenode.conf || die "savenode.conf missing ENABLE=x"

        SNODE=$(grep NODE= $CONFIGS/savenode.conf | awk -F'=' '{print $2}')

        SPASSWORD=$(grep PASSWORD= $CONFIGS/savenode.conf | awk -F'=' '{print $2}')

        SENABLE=$(grep ENABLE= $CONFIGS/savenode.conf | awk -F'=' '{print $2}')

        if [ $NODE != $SNODE ]

        then

                die "Node numbers in iax.conf and savenode.conf are different!"

        fi

        if [ $REGPSWD != $SPASSWORD ]

        then

                die "Passwords in iax.conf and savenode.conf are different!"

        fi

        if [ -z $SENABLE ]

        then

                die "Enable not fully specified in savenode.conf!"

        fi

fi

echo "OK, the format of the files is understandable!"

echo

ANYNEW=0

NEWNODE=""

echo The system node number is: $NODE

promptyn "Would you like to change it?"

if [ "$ANSWER" = "Y" ]

then

        promptnum "Enter the new node number"

        NEWNODE=$ANSWER

        ANYNEW=1

fi

NEWPSWD=""

echo The registration password is: $REGPSWD

promptyn "Would you like to change it?"

if [ "$ANSWER" = "Y" ]

then

        promptnum "Enter the new registration password"

        NEWPSWD=$ANSWER

        ANYNEW=1

fi

ID=""

promptyn "Would you like to enter a callsign for the identifier"

if [ "$ANSWER" = "Y" ]

then

        promptcall "Please enter your callsign"

        ID=$ANSWER

        ANYNEW=1

fi

if [ $SAVENODE_ENABLE -ne $SENABLE ]

then

        ANYNEW=1

fi

if  [ $ANYNEW -gt 0 ]

then

        echo "Copying original files to temporary work area..."

        cp $CONFIGS/rpt.conf $TMP/rpt.conf.in || die "Could not copy $CONFIGS/rpt.conf"

        cp $CONFIGS/extensions.conf $TMP/extensions.conf.in || die "Could not copy $CONFIGS/extensions.conf"

        cp $CONFIGS/iax.conf $TMP/iax.conf.in || die "Could not copy $CONFIGS/iax.conf"

        if [ -e $CONFIGS/savenode.conf ]

        then

                cp $CONFIGS/savenode.conf $TMP/savenode.in || die "Could not copy $CONFIGS/savenode.conf"

        fi

else

        echo "Nothing to do!"

        exit 0

fi

if [ ! -z $ID ]

then

        echo "Updating rpt.conf with new ID..."

        sed "s~idrecording[ \t]*=[ \t]*|.*~idrecording = |i$ID\t\t\t; Main ID message~" <$TMP/rpt.conf.in >$TMP/rpt.conf.out

        mv -f $TMP/rpt.conf.out $TMP/rpt.conf.in || die "mv 1 failed"

        sed "s~idtalkover[ \t]*=[ \t]*|.*~idtalkover = |i$ID\t\t\t; Talkover ID message~" <$TMP/rpt.conf.in >$TMP/rpt.conf.out

        mv -f $TMP/rpt.conf.out $TMP/rpt.conf.in || die "mv 1 failed"

fi

if [ ! -z $NEWNODE ]

then

        echo "Updating rpt.conf iax.conf, and extensions.conf with new node number..."

        sed "s/$NODE/$NEWNODE/g" <$TMP/extensions.conf.in >$TMP/extensions.conf.out

        mv -f $TMP/extensions.conf.out $TMP/extensions.conf.in || die "mv 2 failed"

        sed "s/$NODE/$NEWNODE/g" <$TMP/rpt.conf.in >$TMP/rpt.conf.out

        mv -f $TMP/rpt.conf.out $TMP/rpt.conf.in || die "mv 3 failed"

        sed "s/$NODE/$NEWNODE/g" <$TMP/iax.conf.in >$TMP/iax.conf.out

        mv -f $TMP/iax.conf.out $TMP/iax.conf.in || die "mv 4 failed"

        if [ -e $CONFIGS/savenode.conf ]

        then

                sed "s/$NODE/$NEWNODE/g" <$TMP/savenode.in >$TMP/savenode.out

                mv -f $TMP/savenode.out $TMP/savenode.in || die "mv 5 failed"

        fi

fi

if [ ! -z $NEWPSWD ]

then

        echo "Updating allstar link register statement in iax.conf with new password..."

        sed "s/$REGPSWD/$NEWPSWD/g" <$TMP/iax.conf.in >$TMP/iax.conf.out

        mv -f $TMP/iax.conf.out $TMP/iax.conf.in || die "mv 6 failed"

        if  [ -e $CONFIGS/savenode.conf ]

        then

                sed "s/$REGPSWD/$NEWPSWD/g" <$TMP/savenode.in >$TMP/savenode.out

                mv -f $TMP/savenode.out $TMP/savenode.in || die "mv 7 failed"

        fi

fi

if  [ -e $CONFIGS/savenode.conf ]

then

        sed "s/ENABLE=$SENABLE/ENABLE=$SAVENODE_ENABLE/g" <$TMP/savenode.in >$TMP/savenode.out

        mv -f $TMP/savenode.out $TMP/savenode.in || die "mv 7 failed"

fi

if [ $DRY_RUN -eq 0 ]

then

        sed -i 's/; register =/register =/g' $TMP/iax.conf.in

        # Used the $ in place of the /

        sed -i 's$;statpost_program = /usr/bin/wget$statpost_program = /usr/bin/wget$g' $TMP/rpt.conf.in

        sed -i "0,/statpost_url/ s/;statpost_url /statpost_url/" $TMP/rpt.conf.in

        echo "Updating original config files..."

        mv -f $TMP/rpt.conf.in $CONFIGS/rpt.conf || die "mv 8 failed"

        mv -f $TMP/extensions.conf.in $CONFIGS/extensions.conf || die "mv 9 failed"

        mv -f $TMP/iax.conf.in $CONFIGS/iax.conf || die "mv 10 failed"

        if  [ -e $CONFIGS/savenode.conf ]

        then

                mv -f $TMP/savenode.in $CONFIGS/savenode.conf || die "mv 11 failed"

                chmod +x $CONFIGS/savenode.conf || die "chmod failed!"

        fi

        echo "Config files updated. Done!!"

        echo

else

        echo "Dry run"

        echo

fi

exit 0