I have a question and a possible clue to the issue
Question:
Would a Dell dimension 8400 with a pentium 4 processer be able to handle two nodes at once? For the most part, the first node will only be connected to the second node and the second node will connect to remote nodes. 

Possible clue to issue
So I was in the radio-tune-menu option number four, the CTCSS detection.  I first did it on node Number 1 and it worked fine just like always. I then tried it on node number 2 and it didn't work and everything was 0. Then I tried it with node number 1 but the USB devices swapped. Node 1 worked, and node 2 didn't. So there is something wrong where no CTCSS will get detected and it is always 0. Here is my USBRADIO.conf 

;
; Usbradio channel driver Configuration File
;

[general]

[usb40764]

hdwtype=0
rxboost=1
txboost=1
rxctcssrelax=1
txctcssdefault=103.5
rxctcssfreqs=103.5
txctcssfreqs=103.5
;rxctcssoverride=0
carrierfrom=dsp
ctcssfrom=dsp
rxdemod=flat
txprelim=yes
txlimonly=no
txtoctype=phase
txmixa=composite
txmixb=no
invertptt=0
duplex=0
rxondelay=30
rxnoisefiltype=0
eeprom=0

;gpio=out1

gpio1 = out0         ; in, out0 or out1
gpio2 = out0
gpio4 = in        ; in, out0 or out1

[usb41694]

hdwtype=0
rxboost=1
txboost=0
rxctcssrelax=1
txctcssdefault=100.0
rxctcssfreqs=100.0
txctcssfreqs=100.0
;rxctcssoverride=0
carrierfrom=usbinvert
ctcssfrom=usbinvert
rxdemod=flat
txprelim=no
txlimonly=no
txtoctype=notone

On Mon, Mar 2, 2015 at 1:04 PM, Skyler F <electricity440@gmail.com> wrote:
Would the green light work as a COR point? I don't know where COR is on the UV5R. 

On Mon, Mar 2, 2015 at 12:04 PM, Mike Zingman <mike.zingman@gmail.com> wrote:
Yes, that is what we did. 

1) set radio for RX CTCSS
2) connect audio from FOB to fixed audio from the audio pot.
3) use COR from radio.  We use the 888 ( mods here may help: http://w0fcm.com/allstar-portable-node/ )

On Mon, Mar 2, 2015 at 1:56 PM, Skyler F <electricity440@gmail.com> wrote:
Did I read correctly that you are trying to use Baofeng speaker audio + USBRadio in order to decode CTCSS?  The Baofeng filters CTCSS from the RX before it hits the speaker.  A little may still leak through, but not enough to work.  Look on the web and you will/may find mods to pick off the carrier detect on the Baofeng.  This will give you the detection you need. 
There aren't any mods that I could find and people told me the speaker output is on the chip itself. 

Can I use the RX CTCSS on the radio and use COR?

On Mon, Mar 2, 2015 at 10:03 AM, Mike Zingman <mike.zingman@gmail.com> wrote:
Skyler,

Did I read correctly that you are trying to use Baofeng speaker audio + USBRadio in order to decode CTCSS?  The Baofeng filters CTCSS from the RX before it hits the speaker.  A little may still leak through, but not enough to work.  Look on the web and you will/may find mods to pick off the carrier detect on the Baofeng.  This will give you the detection you need. 

If I have this wrong, never mind ;-)


On Mon, Mar 2, 2015 at 10:32 AM, Skyler F <electricity440@gmail.com> wrote:
ACID

On Mon, Mar 2, 2015 at 8:28 AM, Kevin Custer <kuggie@kuggie.com> wrote:
On 3/2/2015 10:25 AM, Skyler F wrote:
USBradio

Dell desktop with pentium 4

I will check the version when I get a chance but there is so much custom built stuff on it, upgrading would probably destroy it. It is from julyish 2014

 Sorry - When I asked for the version of distribution, I meant ACID or XIPAR?




--

_______________________________________________
App_rpt-users mailing list
App_rpt-users@ohnosec.org
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users

To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.




--




--



--
Skyler Fennell
amsatnet.info
KDØWHB
electricity440@gmail.com