All connections good except for the red one in question.

Change 22  to pin 21 on the FR 5000 and program the I/O pin 21 as an output. Then assign  function "Analog audible" .
set logic to LOW.

This will give you an analog COR that is active low when the receiver is active-should you require it.

Program I/O pin 19 to an input and select "EPTT" as its function and set the logic to LOW.

This will make this pin an external ptt.

In you uri set up set the following:

[usb1999]

hdwtype=0   
rxboost=1
txboost=1
rxctcssrelax=1
txctcssdefault=103.5
rxctcssfreqs=103.5
txctcssfreqs=103.5
;rxctcssoverride=0
carrierfrom=dsp
ctcssfrom=dsp
rxdemod=flat
txprelim=no
txlimonly=yes
txtoctype=phase
txmixa=voice
txmixb=no
invertptt=0
duplex=1
rxondelay=0
rxnoisefiltype=0
eeprom=0
plfilter=yes

This will set you up using dsp for squelch detection and dsp for rx tone detection.

This setup requires the Icom to be programmed to transmit the ctcss tone (if desired). the URI will only send Voice to the Icom.

Calibrate your RXnoise, RXvoice and RXtone. Then set TX Voice.

Save your settings.

If your squelch is open type this at the prompt:

repeater*CLI> radio tune rxsquelch
Current Signal Strength is 681
Current Squelch setting is 500

if your squelch setting is below your signal strength, set the squelch to something about 25 points above the current signal strength.

repeater*CLI> radio tune rxsquelch 700
press enter.

Save settings.

This set up will require a ctcss tone of 103.5 Hz to access the receive.

Also, if you intend to use the allstar node to repeat then set the channel in the repeater to "duplex" .
This is to ensure the allstar node is repeating and not the Icom.

Hope this helps.

Cheers!

Jon VA3RQ





On 12/8/2018 5:50 AM, Lardizabal David D. wrote:
Hi

My name is David Lardizabal HQ2DDL.  I am trying to install and AllstarLink node with a repeater Icom FR 5000 and I am trying to figure out the pinout / setting on repeater.  If anyone has done this setup would appreciate the help.

I have all ready have done some testing but I am getting a lot of noice, like the squelch is open and transmitting to connected node, ( I am able to connect to other nodes via line command, I have not been able to get the DTMF tones to work to connect/disconnect to nodes.)

My current pin out is like this:  


FR 5000 Repeater DML URI

7 GND =================> 20 GND
8 MOD IN   =================> 22 TX AUDIO
9 DISC OUT ================> 21 RX AUDIO
14 GND  =================> 19 GND
19 PTT =================>  1 PTT
22 AF OUT  =================>  8 COR DET   (?)

*** as a Note: I found out in a pin out for RTCM with an ICOM FR6000 repeater;

I recently connected a Micro-Node RTCM to an ICOM FR6000 UHF repeater.
The FR5000/6000 has a DB25 auxiliary connector on the rear.
Here is the sable pin-out I used. Maybe this helps someone else.

FR6000                                     RTCM
----------------------------------------------------------------------
Pin 11 - 12VDC Out ------------------ Pin 1 +V In
Pin 8 - MOD IN ------------------------- Pin 2 TX Audio
Pin 9 Discriminator ------------------- Pin 3 RX Audio
Pin 21 Analog Audible Out -------- Pin 4 CTCSS In
Pin 14 GND------------------------------ Pin 5 GND
Pin 19 EPTT ---------------------------- Pin 7 PTT
DB25 Shell --- soldered to braid---DB9 Shell

Programming FR6000.
Configured for CTCSS on Receive, no CTCSS on transmit.
Program Pin 21 I/O for Audible Out which is a signal indication when the
receiver is unmuted by squelch/tone.
Program Pin 19 I/O for EPTT - External PTT

73

David


_______________________________________________
App_rpt-users mailing list
App_rpt-users@lists.allstarlink.org
http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users

To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.