Thanks
Ken, but this did not work..
Here
is what I did..
[root@KA4EPS-R-Margate
xpmr]# cd /usr/src/asterisk/asterisk/channels/xpmr
[root@KA4EPS-R-Margate
xpmr]# pwd
/usr/src/asterisk/asterisk/channels/xpmr
[root@KA4EPS-R-Margate
xpmr]# make
make:
*** No targets specified
and no makefile found. Stop.
[root@KA4EPS-R-Margate
xpmr]# make install
make:
*** No rule to make
target `install'. Stop.
[root@KA4EPS-R-Margate
xpmr]#
I
assume I have the correct directory?
From: Ken
[mailto:ke2n@cs.com]
Sent: Sunday, December 25, 2011 12:26
AM
To: 'Lu Vencl'; 'Jim Duuuude'; w7ry@centurytel.net; 'app_rpt
mailing list'
Subject: RE: [App_rpt-users] CTCSS Drop Out
Time
Lu
You
make the change to the file, save it and then go to the Linux command line
(usually in the source directory above) and type
make
you
will see a number of lines scroll by followed by:
make[1]:
Leaving directory `/usr/src/astsrc/asterisk/main'
+---------
Asterisk Build Complete ---------
+
Asterisk has successfully been built, and
+
can be installed by
running:
+
+
make
install
+-------------------------------------------+
So
then you type
make
install
and
again a bunch of stuff scrolls by, ending with
+----
Asterisk Installation Complete -------+
+
+
YOU MUST READ THE SECURITY DOCUMENT
+
+
Asterisk has successfully been installed.
+
If you would like to install the sample
+
configuration files (overwriting any
+
existing config files),
run:
+
+
make
samples
+
+-----------------
or ---------------------
+
+
You can go ahead and install the asterisk
+
program documentation now or later run: +\
+
+
make
progdocs
+
+
**Note** This requires that you have
+
doxygen installed on your local system
+-------------------------------------------
The
you type
astres.sh
And
you are good to go
Merry
Christmas
Ken
From: Lu Vencl
[mailto:vencl@att.net]
Sent: Saturday, December 24, 2011 11:20
PM
To: 'Ken'; 'Jim Duuuude'; w7ry@centurytel.net; 'app_rpt mailing
list'
Subject: RE: [App_rpt-users] CTCSS Drop Out
Time
Yeap,
I was the one that brought that up several months ago, but I never could figure
out how to “make / make install” .
I
have no clue what that means.. If someone could help me out with that, I will
finally get this to 1200 MS which will cover my Yasue
radios.
Thanks!
KA4EPS
From: app_rpt-users-bounces@ohnosec.org
[mailto:app_rpt-users-bounces@ohnosec.org]
On Behalf Of Ken
Sent: Saturday, December 24, 2011 9:02
PM
To: 'Jim Duuuude'; w7ry@centurytel.net; 'app_rpt mailing
list'
Subject: Re: [App_rpt-users] CTCSS Drop Out
Time
Notone
AKA chicken burst gives you carrier with no tone at the
end.
But
some radios are too slow in closing the CTCSS and still make
noise.
There
was a posting on here a while back that pointed the time delay in:
/usr/src/asterisk/asterisk/channels/xpmr/xpmr.h
The
default is 600 ms. Some radios might be slower than
this.
You
could change (increase) it, then make / make install and restart
asterisk.
My
Alinco DR-?35 series seem to want to give you a small squelch tail no matter
what you do, however…
73
Ken
From: app_rpt-users-bounces@ohnosec.org
[mailto:app_rpt-users-bounces@ohnosec.org]
On Behalf Of Jim Duuuude
Sent: Saturday, December 24, 2011 6:17
PM
To: w7ry@centurytel.net;
app_rpt mailing list
Subject: Re: [App_rpt-users] CTCSS Drop Out
Time
try
txtoctype
= notone
in usbradio.conf
JIM WB6NIL
From: w7ry@centurytel.net
To: app_rpt-users@ohnosec.org
Date:
Sat, 24 Dec 2011 13:55:51 -0800
Subject: [App_rpt-users] CTCSS Drop Out
Time
Anyone know if
there is an adjustment of the time the transmitter stays keyed, and the
PL tone drops out and where that setting is?
With my rigs, I
still here the squelch crash after the repeater drops out. I would like to cut
the PL off a little sooner or delay the transmitter a little longer.
BTW, I'm all up and
running with the repeater function and the node! Thanks to all that helped
me get past the learning curve!
Thanks!
Merry
Christmas
73 Jim
W7RY
_______________________________________________
App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
No virus found in this
message.
Checked by AVG - www.avg.com
Version: 2012.0.1901 / Virus
Database: 2109/4701 - Release Date: 12/24/11