There is a pattern to the debug out put which looks like below. Sure would like to decode this:

It's happy when there are all zeros. Then it does 18 08 06

GPS-DEBUG: TSIP: ok 1, 9 - 14: 00 00 00 00 00 00

GPS-DEBUG: TSIP: ok 0, 9 - 14: 00 00 00 18 08 06

07/10/2017 20:35:42.100 GPS signal lost entirely. Starting again...

07/10/2017 20:35:42.100 Host Connection Lost (Pri) (192.168.1.6)

GPS-DEBUG: TSIP: ok 0, 9 - 14: 00 00 00 08 08 05

GPS Receiver Active, waiting for aquisition

GPS-DEBUG: TSIP: ok 0, 9 - 14: 00 00 00 08 08 05

Repeats, trimmed for brevity.

GPS-DEBUG: TSIP: ok 0, 9 - 14: 00 00 00 08 08 05

GPS-DEBUG: TSIP: ok 0, 9 - 14: 00 00 00 00 00 05

GPS-DEBUG: TSIP: ok 1, 9 - 14: 00 00 00 00 00 08

GPS signal acquired

GPS-DEBUG: TSIP: ok 1, 9 - 14: 00 00 00 00 00 08

07/10/2017 20:36:03.100 Time now syncronized to GPS

GPS-DEBUG: TSIP: ok 1, 9 - 14: 00 00 00 00 00 08

07/10/2017 20:36:03.500 Host Connection established (Pri) (192.168.1.6)

GPS-DEBUG: TSIP: ok 1, 9 - 14: 00 00 00 00 00 08

Repeats, trimmed for brevity.

GPS-DEBUG: TSIP: ok 1, 9 - 14: 00 00 00 00 00 08

GPS-DEBUG: TSIP: ok 0, 9 - 14: 00 00 00 00 00 04

07/10/2017 20:36:52.200 GPS signal lost entirely. Starting again...

07/10/2017 20:36:52.220 Host Connection Lost (Pri) (192.168.1.6)

GPS-DEBUG: TSIP: ok 0, 9 - 14: 00 00 00 00 00 04

GPS Receiver Active, waiting for aquisition

GPS-DEBUG: TSIP: ok 1, 9 - 14: 00 00 00 00 00 00

GPS signal acquired

GPS-DEBUG: TSIP: ok 1, 9 - 14: 00 00 00 00 00 00

07/10/2017 20:36:56.220 Time now syncronized to GPS

GPS-DEBUG: TSIP: ok 1, 9 - 14: 00 00 00 00 00 00

07/10/2017 20:36:56.500 Host Connection established (Pri) (192.168.1.6)

GPS-DEBUG: TSIP: ok 1, 9 - 14: 00 00 00 00 00 00

Now it will have all zeros until the next loss, which could be minutes or hours.

On Mon, Jul 10, 2017 at 1:29 PM, Jesse Lloyd <ve7lyd@gmail.com> wrote:

I've had problems with the VHF transmitter antennas being too close to the GPS antenna and RF swamping it. If you go to site and use the Trimble software to see satellite signal data then key the transmitter, mine would show a loss of almost all the satellites.

Cheers,
Jesse

On Jul 10, 2017, at 1:17 PM, Tim Sawyer <tisawyer@gmail.com> wrote:

My RTCM, two of then actually on the same Trimble, are loosing lock of late. The output from the RTCM Debug mode 40 is shown below. I read that all zeros was good but I'm wondering 08 and 04 in the last byte mean. Does any know how to decode this?

GPS-DEBUG: TSIP: ok 1, 9 - 14: 00 00 00 00 00 08

GPS-DEBUG: TSIP: ok 1, 9 - 14: 00 00 00 00 00 08

GPS-DEBUG: TSIP: ok 1, 9 - 14: 00 00 00 00 00 08

GPS-DEBUG: TSIP: ok 1, 9 - 14: 00 00 00 00 00 08

GPS-DEBUG: TSIP: ok 1, 9 - 14: 00 00 00 00 00 08

GPS-DEBUG: TSIP: ok 1, 9 - 14: 00 00 00 00 00 08

GPS-DEBUG: TSIP: ok 0, 9 - 14: 00 00 00 00 00 04

07/10/2017 20:08:22.160 GPS signal lost entirely. Starting again...

07/10/2017 20:08:22.160 Host Connection Lost (Pri) (192.168.1.6)

GPS-DEBUG: TSIP: ok 0, 9 - 14: 00 00 00 00 00 04

GPS Receiver Active, waiting for aquisition

GPS-DEBUG: TSIP: ok 1, 9 - 14: 00 00 00 00 00 00

GPS signal acquired

GPS-DEBUG: TSIP: ok 1, 9 - 14: 00 00 00 00 00 00

07/10/2017 20:08:26.160 Time now syncronized to GPS

GPS-DEBUG: TSIP: ok 1, 9 - 14: 00 00 00 00 00 00

07/10/2017 20:08:26.500 Host Connection established (Pri) (192.168.1.6)

GPS-DEBUG: TSIP: ok 1, 9 - 14: 00 00 00 00 00 00

GPS-DEBUG: TSIP: ok 1, 9 - 14: 00 00 00 00 00 00

--
--
Tim

_______________________________________________
App_rpt-users mailing list
App_rpt-users@lists.allstarlink.org
http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users

To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.

_______________________________________________
App_rpt-users mailing list
App_rpt-users@lists.allstarlink.org
http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users

To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.

Tim