Personally I wouldn't bother with using the tone boards in
the MII.
On both of mine, I just pulled VOL/SQL HI from the backplane.
Then let the usbradio DSP do it all.
On the MIIe (direct FM exciter) I was able to feed both CG
and voice into the CG input of the exciter. Measured it to be
flat to 8 KC. Then let usbradio do the pre-emphasis, CG
encode/decode, and de-emphasis.
On the regular MII (phase modulated exciter), again all DSP.
Voice into the exciter mic input, CG encode to the CG input.
With the exciter doing the pre-emphasis.
Robert A. Poff
Loganville, Pa
From: Chris Viningre
Sent: Sun Nov 06 16:19:11 EST 2016
To: Bob Poff
Cc: app_rpt-users@ohnosec.org
Subject: Re: [App_rpt-users] No PL Tone
I may have been unclear on the problem. I can not get the
repeater to tone squelch. It is always open. The repeater is
working fine other then that. I have tried these settings and
still no luck. Thanks for all the help.
Chris
On 11/06/2016 10:55 AM, Bob Poff
wrote:
First of all, you need carrierfrom=dsp not usb.
carrierfrom=dsp ; Carrier Detect Source ; Options -
no,usb,usbinvert,dsp,vox ; no - no carrier detection at all ;
usb - via USB radio adapter COR connection ; usbinvert - same
as above but inverted polarity. ; dsp - from RX noise using
dsp methods ; vox - voice activated via RX audio
Robert A. Poff
Loganville, Pa
I am trying to get the PL tone of 100.0 hz to work on my GE Mastr II
repeater. I'm using a URI interface on a laptop running Dail software.
Everything is working other than the tones. Here is my rpt.conf and
usbradio.conf. Thanks for any help.
Chris Viningre
70 W. Roadrunner
Salt Flat, Texas 79847
C:(915) 504-1510
chrisviningre@gmail.com
Amateur Radio Operator: WS5B
https://www.qrz.com/db/ws5b
http://www.reverbnation.com/chrisviningre
Radio Repeater configuration file (for use with app_rpt)
;
;
; Your Repeater
;
[43934] ; Change this to your assigned node
number
rxchannel=Radio/usb43934
duplex=2
erxgain=-3
etxgain=3
;controlstates=controlstates
scheduler=schedule43934
morse=morse43934
macro=macro43934
functions=functions43934
phone_functions=functions43934
link_functions=functions43934
telemetry=telemetry
wait_times=wait-times
context = radio
callerid = "Repeater" <0000000000>
idrecording = |iWS5B
accountcode=RADIO
hangtime=1000
;
; Usbradio channel driver Configuration
File
;
[general]
[usb43934]
hdwtype=0
rxboost=1
txboost=1
rxctcssrelax=1
txctcssdefault=100.0
rxctcssfreqs=100.0
txctcssfreqs=100.0
;rxctcssoverride=0
carrierfrom=usb
ctcssfrom=usb
rxdemod=speaker
txprelim=no
txlimonly=no
txtoctype=no
txmixa=composite
txmixb=no
invertptt=0
duplex=1
rxondelay=0
rxnoisefiltype=0
eeprom=0
App_rpt-users mailing list
App_rpt-users@ohnosec.org
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options
button"
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________
App_rpt-users mailing list
App_rpt-users@ohnosec.org
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.