Thank you so much for your reply.

I have the latest download of Debian from Allstar link. I have it installed on a amd desk top pc and then it linked to pm windows pc with putty.

I have a dmk engineering usb radio interface to a Motorola gm300 type radio.

I understand this is very difficult to do over email but I have worked on this off and on for two years and I am just at wits end. I go through the asl-menu and have it configured the static ip address and have signed up with Allstar and have my numbers and passwords with server and my pc.

My problem is when I try to go to tune radio menu it comes up with a message that I don't have rpt file and another one I cant remember with out going and firing up pc again and refreshing my memory not configured.

So in other words I just don't know which of the hundreds of lines in the files usb radio, simpleusb or other files need to be modified.

I will keep reading the help files and and k5tra's web site but I just can't seem to get the files configured right.

Thanks so much

Dale

N0INX

On Mon, Jun 25, 2018 at 11:58 PM, Mike <mm@midnighteng.com> wrote:

Well,

I am not sure what you are using for hardware and what versions of software as you did not say.

SO here is my advise for anyone.

Make the box work 'headless', meaning without the radios in the setup fray.

Use this setting by un/commenting the following lines as shown here in your rpt.cong file so you are using dahdi/pseudo and not radio interfaces.

rxchannel = dahdi/pseudo            ; No radio (hub)    ******************
; rxchannel = SimpleUSB/usb_29999    ; SimpleUSB
; rxchannel = Pi/1                      ; Raspberry Pi PiTA
; rxchannel = Radio/usb_29999        ; USBRadio (DSP)
; rxchannel = Dahdi/1            ; PCI Quad card
; rxchannel = Beagle/1            ; BeagleBoard
; rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio interface USRP

duplex = 2                              ; 0 = Half duplex with no telemetry tones or hang time.

Then setup iaxrpt to run with that node so you can check it for functionality of a running asterisk install without the radio side of the equation.

You will have to read some more of the docs most likely to get this far, but once you do, you are most of the way there.

You should be able to 'command' your node with functionality before adding radios to your learning curve.

But you will need to ask 'specific questions' to what you do not understand to get help.

...mike/kb8jnm

On 6/25/2018 9:38 PM, Dale Day wrote:
Could someone help me with getting allstar link up and running.
I just can't allstar configured correctly to the point where I can tune the radios.

I just don't understand what I am doing wrong.
_______________________________________________
App_rpt-users mailing list
App_rpt-users@lists.allstarlink.org
http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users

To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. 
_______________________________________________
App_rpt-users mailing list
App_rpt-users@lists.allstarlink.org
http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users

To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.