Sorry for the mistake. For some reason the previous Xelatec links caused me to think of that. But it is an address issue. I just got finished with a Xipar node that did the same behavior. Ran fine, Green light lit but no heartbeat. Despite hot swapping the fobs which resulted in the OS seeing it, I finally realized the tune file forced the selection. Good luck as I don't run DIAL 73s On May 21, 2016 5:38 PM, <app_rpt-users-request@ohnosec.org> wrote: Send App_rpt-users mailing list submissions to app_rpt-users@ohnosec.org To subscribe or unsubscribe via the World Wide Web, visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users or, via email, send a message with subject or body 'help' to app_rpt-users-request@ohnosec.org You can reach the person managing the list at app_rpt-users-owner@ohnosec.org When replying, please edit your Subject line so it is more specific than "Re: Contents of App_rpt-users digest..." Today's Topics: 1. Re: . usbradio_tune_xxxxx.conf where .conf = .confusion (Steve Agee (Steve Agee) ---------------------------------------------------------------------- Message: 1 Date: Sat, 21 May 2016 16:38:16 -0500 From: Steve Agee <n5zua@earthlink.net> To: app_rpt-users@ohnosec.org Subject: Re: [App_rpt-users] . usbradio_tune_xxxxx.conf where .conf = .confusion (Steve Agee Message-ID: <ba084f3d-f4d2-017b-04e4-11c5cace0f7d@earthlink.net> Content-Type: text/plain; charset="windows-1252"; Format="flowed" Thanks, but as previously mentioned, this is DIAL and so your CLI commands from XIPAR do not exist. N5ZUA On 5/21/2016 4:36 PM, KM4NRJ FLORIDA wrote:

Excuse my mistake.

Edit the urd_tune_usb.conf not urd.conf

On May 21, 2016 17:08, <app_rpt-users-request@ohnosec.org <mailto:app_rpt-users-request@ohnosec.org>> wrote:

If you are using Xipar then under the CLI use:

radio probe on

It will scan all currently connected Fobs and indicate bus and device number.

radio probe off

will stop the scan.

Edit the urd.conf file to set device parameters accordingly.

Restart Asterisk

On May 21, 2016 17:08, <app_rpt-users-request@ohnosec.org <mailto:app_rpt-users-request@ohnosec.org>> wrote:

Send App_rpt-users mailing list submissions to app_rpt-users@ohnosec.org <mailto:app_rpt-users@ohnosec.org>

To subscribe or unsubscribe via the World Wide Web, visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users or, via email, send a message with subject or body 'help' to app_rpt-users-request@ohnosec.org <mailto:app_rpt-users-request@ohnosec.org>

You can reach the person managing the list at app_rpt-users-owner@ohnosec.org <mailto:app_rpt-users-owner@ohnosec.org>

When replying, please edit your Subject line so it is more specific than "Re: Contents of App_rpt-users digest..."

Today's Topics:

1. usbradio_tune_xxxxx.conf where .conf = .confusion (Steve Agee) 2. Voter RTCM sometimes offline-mode but not when there is a telnet connection (info@rainerbertsch.de <mailto:info@rainerbertsch.de>) 3. Re: usbradio_tune_xxxxx.conf where .conf = .confusion (kk6ecm) 4. Re: usbradio_tune_xxxxx.conf where .conf = .confusion (Steve Agee)

----------------------------------------------------------------------

Message: 1 Date: Sat, 21 May 2016 14:04:56 -0500 From: Steve Agee <n5zua@earthlink.net <mailto:n5zua@earthlink.net>> To: app_rpt-users@ohnosec.org <mailto:app_rpt-users@ohnosec.org> Subject: [App_rpt-users] usbradio_tune_xxxxx.conf where .conf = .confusion Message-ID: <c5dc4bf0-2c2c-3566-f32e-31a311653463@earthlink.net <mailto:c5dc4bf0-2c2c-3566-f32e-31a311653463@earthlink.net>> Content-Type: text/plain; charset="windows-1252"; Format="flowed"

Hello list:

I've searched

<http://www.xelatec.com/xipar/node/180>

and I fully understand the description/explanations given. What I don't understand, with specific attention to the lines:

|; name=usb ; ; devnum=1 ; devstr=4-2 ;

is how to manually uncomment, and manipulate them. In this particular instance, I'm trying to get a DIAL box running with one original URI (early version) using the USBRADIO channel driver, and one URIX (newer version) using the SIMPLEUSB channel driver. I've followed the step-by-step (or was that Crossbar 5 Duude?) instructions for starting off with a single node, then adding the second node. That simply doesn't work. The second URIx green L.E.D. stays solid throughout the process. Are these lines provided for informational purposes only, or can they be edited to force the second device to be recognized and assigned?

N5ZUA

|