Need help connecting a Baofeng UV-5R with DMK URI-x
Dear List members Good morning. I need a bit of help in connecting a Baofeng UV-5R with DMK URIx device. I have googled as much as I practically could, but still could not decide/confirm as to what should be the approach. First of all, I came across the pin-out for the baofeng at Miklor site http://www.miklor.com/COM/UV_Technical.php I have also seen how DMK suggests any generic radio should be connected at http://www.dmkeng.com/images/9080-FRS.pdf And finally, I have found the site that shows how to get the COR out of baofeng http://alaskareflector.org/zl1nc/UV-COS.html Now, my expertise in electronics is sub-zero -- I know some very basics about what component does what, and that's all. So, I have several questions, and would appreciate if someone with sufficient relevant experience could please point me to the correct decision. 1. the URI diagram uses several resistors, do I really need them? Or should I just connect things direct? 2. the main URI diagram shows pin 7 as CTCSS_det and pin 8 as COR_det, so should I connect the COR from baofeng to pin 8? 3. based on what I can understand from all the links above, I should connect large stereo body -> D-Sub pin 1 large stereo ring -> D-Sub pin 22 small stereo tip -> D-Sub pin 21 COR (taken from pin 2 of the IC) -> D-Sub pin 8 Is the above correct? Or do you have different experience? Thanks for your response. Regards Shamim
I am also looking to connect a UV-5R to the URI-X but using ONLY the speaker/mike jack and usbradio with DSP detection of audio - the radio will do the CTCSS handling and should only provide audio when CTCSS is met. Thanks! Steven Donegan KK6IVC General Class FCC License Silver State Car #86 www.sscc.us From: Shamim Shahriar <shamim.shahriar@gmail.com> To: app_rpt-users@ohnosec.org Sent: Monday, November 2, 2015 4:45 PM Subject: [App_rpt-users] Need help connecting a Baofeng UV-5R with DMK URI-x Dear List members Good morning. I need a bit of help in connecting a Baofeng UV-5R with DMK URIx device. I have googled as much as I practically could, but still could not decide/confirm as to what should be the approach. First of all, I came across the pin-out for the baofeng at Miklor site http://www.miklor.com/COM/UV_Technical.php I have also seen how DMK suggests any generic radio should be connected at http://www.dmkeng.com/images/9080-FRS.pdf And finally, I have found the site that shows how to get the COR out of baofeng http://alaskareflector.org/zl1nc/UV-COS.html Now, my expertise in electronics is sub-zero -- I know some very basics about what component does what, and that's all. So, I have several questions, and would appreciate if someone with sufficient relevant experience could please point me to the correct decision. 1. the URI diagram uses several resistors, do I really need them? Or should I just connect things direct? 2. the main URI diagram shows pin 7 as CTCSS_det and pin 8 as COR_det, so should I connect the COR from baofeng to pin 8? 3. based on what I can understand from all the links above, I should connect large stereo body -> D-Sub pin 1 large stereo ring -> D-Sub pin 22 small stereo tip -> D-Sub pin 21 COR (taken from pin 2 of the IC) -> D-Sub pin 8 Is the above correct? Or do you have different experience? Thanks for your response. Regards Shamim _______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
Hello all Further to my previous email, i have come across this link http://latinovoip.net/baofeng-uv-6-as-an-irlpecholinkallstarlink-2-meter-or-... This one is using a UV-6R, but i am assuming that the pinout for speaker mic is the same. Would appreciate if someone could please confirm. Thanks and regards Shamim On 3 Nov 2015 13:37, "Steven Donegan" <donegan@donegan.org> wrote:
I am also looking to connect a UV-5R to the URI-X but using ONLY the speaker/mike jack and usbradio with DSP detection of audio - the radio will do the CTCSS handling and should only provide audio when CTCSS is met.
Thanks!
Steven Donegan KK6IVC General Class FCC License Silver State Car #86 www.sscc.us
------------------------------ *From:* Shamim Shahriar <shamim.shahriar@gmail.com> *To:* app_rpt-users@ohnosec.org *Sent:* Monday, November 2, 2015 4:45 PM *Subject:* [App_rpt-users] Need help connecting a Baofeng UV-5R with DMK URI-x
Dear List members
Good morning. I need a bit of help in connecting a Baofeng UV-5R with DMK URIx device. I have googled as much as I practically could, but still could not decide/confirm as to what should be the approach.
First of all, I came across the pin-out for the baofeng at Miklor site http://www.miklor.com/COM/UV_Technical.php I have also seen how DMK suggests any generic radio should be connected at http://www.dmkeng.com/images/9080-FRS.pdf
And finally, I have found the site that shows how to get the COR out of baofeng http://alaskareflector.org/zl1nc/UV-COS.html
Now, my expertise in electronics is sub-zero -- I know some very basics about what component does what, and that's all. So, I have several questions, and would appreciate if someone with sufficient relevant experience could please point me to the correct decision.
1. the URI diagram uses several resistors, do I really need them? Or should I just connect things direct? 2. the main URI diagram shows pin 7 as CTCSS_det and pin 8 as COR_det, so should I connect the COR from baofeng to pin 8? 3. based on what I can understand from all the links above, I should connect
large stereo body -> D-Sub pin 1 large stereo ring -> D-Sub pin 22 small stereo tip -> D-Sub pin 21 COR (taken from pin 2 of the IC) -> D-Sub pin 8
Is the above correct? Or do you have different experience?
Thanks for your response.
Regards Shamim
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
participants (2)
-
Shamim Shahriar -
Steven Donegan