If they are on the same server they should know about each other and you should be able to connect directly internally. Is that not working? 73 Doug WA3DSP http://www.crompton.com/hamradio Subject: Re: [App_rpt-users] How to Hardwire Two Nodes in One APP_RPT Server From: kk6ecm@gmail.com Date: Fri, 3 Jul 2015 11:26:00 -0700 To: doug@crompton.com Let me re ask my question. Single server with two nodes, no internet; how do I setup app_rpt so the two nodes are always linked (" hard wired", if you will). What is the difference in the *.conf setup for a permanent link between the nodes? I know how to set up the nodes for each radio, just not clear how to link them via the *.conf file setups (e.g. rpt.conf, iax.conf, extensions.conf). Thanks,Bobkk6ecm Sent from iPad On Jul 3, 2015, at 10:47 AM, Doug Crompton <doug@crompton.com> wrote: If it is RF connect via radio and it is is wired connect via that. Both will work equally well if the routing is setup properly. No need to have Internet access. 73 Doug WA3DSP http://www.crompton.com/hamradio Subject: Re: [App_rpt-users] How to Hardwire Two Nodes in One APP_RPT Server From: kk6ecm@gmail.com Date: Fri, 3 Jul 2015 07:46:21 -0700 CC: app_rpt-users@ohnosec.org To: doug@crompton.com Two servers connected via an rf link between one node on each server. One server is remote, supporting the rf link and a repeater (no internet), and the second is a normal Allster server with two registered nodes, one connected to a repeater, and the second connected to the radio support its half of the rf link with the other server. Thanks,Bobkk6ecm Sent from iPad On Jul 3, 2015, at 6:18 AM, Doug Crompton <doug@crompton.com> wrote: I am assuming these are two separate servers. If so they just have to be on a LAN connected together and the routing has to be setup at each server. They do not have to be registered. In this way they operate as private nodes. Of course anything that needs the Internet will not work. Here is info on doing the routing. It applies equally to any Allstar node - Acid, BBB, RPi2, etc. http://www.crompton.com/hamradio/BeagleBoneBlackAllstar/multi-server%20howto... 73 Doug WA3DSP http://www.crompton.com/hamradio

From: kk6ecm@gmail.com To: app_rpt-users@ohnosec.org Date: Thu, 2 Jul 2015 22:28:17 -0700 Subject: [App_rpt-users] How to Hardwire Two Nodes in One APP_RPT Server

I'm looking for information on how to "hardwire" link two nodes together in my server. One node is full-duplex repeater and the other is a half-duplex RF link to a second repeater that has full Allstar control on both the repeater and the link. They are located at a remote site, with no internet connection after install. I'm sure there are other things I'm missing, but this will enable me to experiment with final configuration combinations.

Thanks, Bob kk6ecm

_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users

To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.