Hello, our repeater is in "carrier squelch"-mode. Since there is much traffic on our repeater we are used to use different subtones for different user groups just for the initial call to request a group member to continue the qso without subtone (so nobody else in the group will be disturbed). Unfortunately this seems to be impossible. We tried these configurations in usbradio.conf: #1 (we tried "0" in rxctcssfreqs/txctcssfreqs in CTCSS dsp-mode) hdwtype=0 ;txctcssdefault=71.9 rxctcssfreqs=0,67.0,71.9,74.4,77.0,79.7,82.5,85.4,88.5,91.5,94.8,97.4,100.0, 103.5,107.2,110.9,114.8,118.8,123.0,127.3,131.8,136.5,141.3,146.2,151.4,156. 7,162.2,167.9,173.8,179.9,186.2,192.8,203.5,210.7,218.1,225.7,233.6,241.8,25 0.3 txctcssfreqs=0,67.0,71.9,74.4,77.0,79.7,82.5,85.4,88.5,91.5,94.8,97.4,100.0, 103.5,107.2,110.9,114.8,118.8,123.0,127.3,131.8,136.5,141.3,146.2,151.4,156. 7,162.2,167.9,173.8,179.9,186.2,192.8,203.5,210.7,218.1,225.7,233.6,241.8,25 0.3 carrierfrom=dsp ctcssfrom=dsp rxdemod=flat txprelim=yes #2 (we tried to disable CTCSS) hdwtype=0 carrierfrom=dsp ctcssfrom=no rxdemod=flat txprelim=yes Is there a way to pass CTCSS tones through the repeater in "carrier squelch"-mode ? I don't care whether it will be decoded/encoded by the software or just passed through the repeater (0-300 Hz passthrough). Currently passthrough of 0-300 Hz seems to be blocked by the software. Thanks 73, Jann DG8NGN -- Jann Traschewski, Drosselstr.1, D-90513 Zirndorf, Germany Tel.: +49-911-696971, Mobile: +49-170-1045937, E-Mail: jann@gmx.de Ham: DG8NGN / DB0VOX, http://www.qsl.net/dg8ngn, ICQ UIN: 4130182
A reasonable and easy request. I went to great extremes (sarcasm intended) to make a 1 line change in chan_usbradio to accommodate this need. A new copy of chan_usbradio.c will be posted to the SVN later today once Steve gets home and does it. It will add the "rxctcssoverride" parameter to usbradio.conf, allowing the rx CTCSS to default to off. (you have to put "rxctcssoverride = yes" in the file. You then specify your CTCSS tones like you would normally (as if you were going to require them for access), but the receiver will not require any tone to actually receive. JIM WB6NIL ----------------------------------------
From: jann@gmx.de To: app_rpt-users@qrvc.com Date: Sat, 6 Mar 2010 17:17:19 +0100 Subject: [App_rpt-users] CTCSS and carrier squelch
Hello,
our repeater is in "carrier squelch"-mode. Since there is much traffic on our repeater we are used to use different subtones for different user groups just for the initial call to request a group member to continue the qso without subtone (so nobody else in the group will be disturbed). Unfortunately this seems to be impossible. We tried these configurations in usbradio.conf:
#1 (we tried "0" in rxctcssfreqs/txctcssfreqs in CTCSS dsp-mode) hdwtype=0 ;txctcssdefault=71.9 rxctcssfreqs=0,67.0,71.9,74.4,77.0,79.7,82.5,85.4,88.5,91.5,94.8,97.4,100.0, 103.5,107.2,110.9,114.8,118.8,123.0,127.3,131.8,136.5,141.3,146.2,151.4,156. 7,162.2,167.9,173.8,179.9,186.2,192.8,203.5,210.7,218.1,225.7,233.6,241.8,25 0.3 txctcssfreqs=0,67.0,71.9,74.4,77.0,79.7,82.5,85.4,88.5,91.5,94.8,97.4,100.0, 103.5,107.2,110.9,114.8,118.8,123.0,127.3,131.8,136.5,141.3,146.2,151.4,156. 7,162.2,167.9,173.8,179.9,186.2,192.8,203.5,210.7,218.1,225.7,233.6,241.8,25 0.3 carrierfrom=dsp ctcssfrom=dsp rxdemod=flat txprelim=yes
#2 (we tried to disable CTCSS) hdwtype=0 carrierfrom=dsp ctcssfrom=no rxdemod=flat txprelim=yes
Is there a way to pass CTCSS tones through the repeater in "carrier squelch"-mode ? I don't care whether it will be decoded/encoded by the software or just passed through the repeater (0-300 Hz passthrough). Currently passthrough of 0-300 Hz seems to be blocked by the software.
Thanks 73, Jann DG8NGN
-- Jann Traschewski, Drosselstr.1, D-90513 Zirndorf, Germany Tel.: +49-911-696971, Mobile: +49-170-1045937, E-Mail: jann@gmx.de Ham: DG8NGN / DB0VOX, http://www.qsl.net/dg8ngn, ICQ UIN: 4130182
_______________________________________________ App_rpt-users mailing list App_rpt-users@qrvc.com http://qrvc.com/mailman/listinfo/app_rpt-users
Hello Jim, thank you for the quick response. I did try the new revision 569, but it doesn't work. My config: hdwtype=0 rxboost=1 rxctcssrelax=1 ;txctcssdefault=71.9 rxctcssfreqs=67.0,71.9,74.4,77.0,79.7,82.5,85.4,88.5,91.5,94.8,97.4,100.0,10 3.5,107.2,110.9,114.8,118.8,123.0,127.3,131.8,136.5,141.3,146.2,151.4,156.7, 162.2,167.9,173.8,179.9,186.2,192.8,203.5,210.7,218.1,225.7,233.6,241.8,250. 3 txctcssfreqs=67.0,71.9,74.4,77.0,79.7,82.5,85.4,88.5,91.5,94.8,97.4,100.0,10 3.5,107.2,110.9,114.8,118.8,123.0,127.3,131.8,136.5,141.3,146.2,151.4,156.7, 162.2,167.9,173.8,179.9,186.2,192.8,203.5,210.7,218.1,225.7,233.6,241.8,250. 3 rxctcssoverride=1 carrierfrom=dsp ctcssfrom=dsp rxdemod=flat txprelim=yes The repeater can be opened now without a subtone. Unfortunately subtones will not be detected and regenerated by the repeater or simply passed through the repeater. Any ideas? Tnx, 73, Jann
-----Original Message----- From: Jim Duuuude [mailto:telesistant@hotmail.com] Sent: Saturday, March 06, 2010 6:05 PM To: Jann; app_rpt mailing list Subject: RE: [App_rpt-users] CTCSS and carrier squelch
A reasonable and easy request. I went to great extremes (sarcasm intended) to make a 1 line change in chan_usbradio to accommodate this need.
A new copy of chan_usbradio.c will be posted to the SVN later today once Steve gets home and does it.
It will add the "rxctcssoverride" parameter to usbradio.conf, allowing the rx CTCSS to default to off. (you have to put "rxctcssoverride = yes" in the file.
You then specify your CTCSS tones like you would normally (as if you were going to require them for access), but the receiver will not require any tone to actually receive.
JIM WB6NIL
----------------------------------------
From: jann@gmx.de To: app_rpt-users@qrvc.com Date: Sat, 6 Mar 2010 17:17:19 +0100 Subject: [App_rpt-users] CTCSS and carrier squelch
Hello,
our repeater is in "carrier squelch"-mode. Since there is much traffic on our repeater we are used to use different subtones for different user groups just for the initial call to request a group member to continue the qso without subtone (so nobody else in the group will be disturbed). Unfortunately this seems to be impossible. We tried these configurations in usbradio.conf:
#1 (we tried "0" in rxctcssfreqs/txctcssfreqs in CTCSS dsp-mode) hdwtype=0 ;txctcssdefault=71.9
rxctcssfreqs=0,67.0,71.9,74.4,77.0,79.7,82.5,85.4,88.5,91.5,94.8,97.4,
100.0,
103.5,107.2,110.9,114.8,118.8,123.0,127.3,131.8,136.5,141.3,14 6.2,151.4,156.
7,162.2,167.9,173.8,179.9,186.2,192.8,203.5,210.7,218.1,225.7,233.6,24
1.8,25 0.3
txctcssfreqs=0,67.0,71.9,74.4,77.0,79.7,82.5,85.4,88.5,91.5,94.8,97.4,
100.0,
103.5,107.2,110.9,114.8,118.8,123.0,127.3,131.8,136.5,141.3,14 6.2,151.4,156.
7,162.2,167.9,173.8,179.9,186.2,192.8,203.5,210.7,218.1,225.7,233.6,24
1.8,25 0.3 carrierfrom=dsp ctcssfrom=dsp rxdemod=flat txprelim=yes
#2 (we tried to disable CTCSS) hdwtype=0 carrierfrom=dsp ctcssfrom=no rxdemod=flat txprelim=yes
Is there a way to pass CTCSS tones through the repeater in "carrier squelch"-mode ? I don't care whether it will be decoded/encoded by the software or just passed through the repeater (0-300 Hz passthrough). Currently passthrough of 0-300 Hz seems to be blocked by the software.
Thanks 73, Jann DG8NGN
-- Jann Traschewski, Drosselstr.1, D-90513 Zirndorf, Germany Tel.: +49-911-696971, Mobile: +49-170-1045937, E-Mail: jann@gmx.de Ham: DG8NGN / DB0VOX, http://www.qsl.net/dg8ngn, ICQ UIN: 4130182
_______________________________________________ App_rpt-users mailing list App_rpt-users@qrvc.com http://qrvc.com/mailman/listinfo/app_rpt-users =
Hi,
thank you for the quick response. I did try the new revision 569, but it doesn't work.
I would like to enter this interesting discussion; during this year I want to move my repeater from Echolink software to the asterisk stuff. The plan so far is to bypass the audio around the PC with a switching matrix, as my repeater is cross band multi mode and does not allow altering the audio in any way. It lets pass FM, P25 and D-Star, and I do not want to loose this capability. But maybe way to pass the audio through the PC without changing a bit could be an option?! I need flat response from almost DC up to some KHz, no DSP processing in the pass-through path at all. This would allow me to keep the status quo, and who knows, maybe some day some real crack writes a regeneration module for digital modulation, even anhancing the digital mode capability, including passing it through the internet. Especially a P25 link from Germany to the US (where more P25 users are on the air) would be very exciting. So, at least I am guy #2 who really needs flat audio response :-) With best regards Ralph, dk5ras (sysop of db0fue).
You have to set a txctcssdefault frequency. If you dont want PL unless someone is encoding it, then include "itxctcss=yes" in app_rpt.c (in the clause for the node), but you still have to specify some tx default frequency whether you ever use it or not. ----------------------------------------
From: jann@gmx.de To: telesistant@hotmail.com; app_rpt-users@qrvc.com Subject: Re: [App_rpt-users] CTCSS and carrier squelch Date: Sun, 7 Mar 2010 06:55:47 +0100
Hello Jim,
thank you for the quick response. I did try the new revision 569, but it doesn't work. My config:
hdwtype=0 rxboost=1 rxctcssrelax=1 ;txctcssdefault=71.9 rxctcssfreqs=67.0,71.9,74.4,77.0,79.7,82.5,85.4,88.5,91.5,94.8,97.4,100.0,10 3.5,107.2,110.9,114.8,118.8,123.0,127.3,131.8,136.5,141.3,146.2,151.4,156.7, 162.2,167.9,173.8,179.9,186.2,192.8,203.5,210.7,218.1,225.7,233.6,241.8,250. 3 txctcssfreqs=67.0,71.9,74.4,77.0,79.7,82.5,85.4,88.5,91.5,94.8,97.4,100.0,10 3.5,107.2,110.9,114.8,118.8,123.0,127.3,131.8,136.5,141.3,146.2,151.4,156.7, 162.2,167.9,173.8,179.9,186.2,192.8,203.5,210.7,218.1,225.7,233.6,241.8,250. 3 rxctcssoverride=1 carrierfrom=dsp ctcssfrom=dsp rxdemod=flat txprelim=yes
The repeater can be opened now without a subtone. Unfortunately subtones will not be detected and regenerated by the repeater or simply passed through the repeater. Any ideas?
Tnx, 73, Jann
-----Original Message----- From: Jim Duuuude [mailto:telesistant@hotmail.com] Sent: Saturday, March 06, 2010 6:05 PM To: Jann; app_rpt mailing list Subject: RE: [App_rpt-users] CTCSS and carrier squelch
A reasonable and easy request. I went to great extremes (sarcasm intended) to make a 1 line change in chan_usbradio to accommodate this need.
A new copy of chan_usbradio.c will be posted to the SVN later today once Steve gets home and does it.
It will add the "rxctcssoverride" parameter to usbradio.conf, allowing the rx CTCSS to default to off. (you have to put "rxctcssoverride = yes" in the file.
You then specify your CTCSS tones like you would normally (as if you were going to require them for access), but the receiver will not require any tone to actually receive.
JIM WB6NIL
----------------------------------------
From: jann@gmx.de To: app_rpt-users@qrvc.com Date: Sat, 6 Mar 2010 17:17:19 +0100 Subject: [App_rpt-users] CTCSS and carrier squelch
Hello,
our repeater is in "carrier squelch"-mode. Since there is much traffic on our repeater we are used to use different subtones for different user groups just for the initial call to request a group member to continue the qso without subtone (so nobody else in the group will be disturbed). Unfortunately this seems to be impossible. We tried these configurations in usbradio.conf:
#1 (we tried "0" in rxctcssfreqs/txctcssfreqs in CTCSS dsp-mode) hdwtype=0 ;txctcssdefault=71.9
rxctcssfreqs=0,67.0,71.9,74.4,77.0,79.7,82.5,85.4,88.5,91.5,94.8,97.4,
100.0,
103.5,107.2,110.9,114.8,118.8,123.0,127.3,131.8,136.5,141.3,14 6.2,151.4,156.
7,162.2,167.9,173.8,179.9,186.2,192.8,203.5,210.7,218.1,225.7,233.6,24
1.8,25 0.3
txctcssfreqs=0,67.0,71.9,74.4,77.0,79.7,82.5,85.4,88.5,91.5,94.8,97.4,
100.0,
103.5,107.2,110.9,114.8,118.8,123.0,127.3,131.8,136.5,141.3,14 6.2,151.4,156.
7,162.2,167.9,173.8,179.9,186.2,192.8,203.5,210.7,218.1,225.7,233.6,24
1.8,25 0.3 carrierfrom=dsp ctcssfrom=dsp rxdemod=flat txprelim=yes
#2 (we tried to disable CTCSS) hdwtype=0 carrierfrom=dsp ctcssfrom=no rxdemod=flat txprelim=yes
Is there a way to pass CTCSS tones through the repeater in "carrier squelch"-mode ? I don't care whether it will be decoded/encoded by the software or just passed through the repeater (0-300 Hz passthrough). Currently passthrough of 0-300 Hz seems to be blocked by the software.
Thanks 73, Jann DG8NGN
-- Jann Traschewski, Drosselstr.1, D-90513 Zirndorf, Germany Tel.: +49-911-696971, Mobile: +49-170-1045937, E-Mail: jann@gmx.de Ham: DG8NGN / DB0VOX, http://www.qsl.net/dg8ngn, ICQ UIN: 4130182
_______________________________________________ App_rpt-users mailing list App_rpt-users@qrvc.com http://qrvc.com/mailman/listinfo/app_rpt-users =
Hi Jim, I set 88.5 Hz now as a default CTCSS-tone: hdwtype=0 rxboost=1 rxctcssrelax=1 txctcssdefault=88.5 rxctcssfreqs=67.0,71.9,74.4,77.0,79.7,82.5,85.4,88.5,91.5,94.8,97.4,100.0,10 3.5,107.2,110.9,114.8,118.8,123.0,127.3,131.8,136.5,141.3,146.2,151.4,156.7, 162.2,167.9,173.8,179.9,186.2,192.8,203.5,210.7,218.1,225.7,233.6,241.8,250. 3 txctcssfreqs=67.0,71.9,74.4,77.0,79.7,82.5,85.4,88.5,91.5,94.8,97.4,100.0,10 3.5,107.2,110.9,114.8,118.8,123.0,127.3,131.8,136.5,141.3,146.2,151.4,156.7, 162.2,167.9,173.8,179.9,186.2,192.8,203.5,210.7,218.1,225.7,233.6,241.8,250. 3 rxctcssoverride=1 carrierfrom=dsp ctcssfrom=dsp rxdemod=flat txprelim=yes I'm able to open the repeater with any or none subtone. The repeater is sending 88.5 Hz subtone all the time. It doesn't matter which subtone I use on my handheld. I want the repeater to send out the subtone I use on my handheld, but it doesn't. I'm currently at the repeaters site and connected to your repeaters. Maybe we can have a short chat on RF. Thank you, 73, Jann
-----Original Message----- From: Jim Duuuude [mailto:telesistant@hotmail.com] Sent: Sunday, March 07, 2010 3:22 PM To: Jann; app_rpt mailing list Subject: RE: [App_rpt-users] CTCSS and carrier squelch
You have to set a txctcssdefault frequency. If you dont want PL unless someone is encoding it, then include "itxctcss=yes" in app_rpt.c (in the clause for the node), but you still have to specify some tx default frequency whether you ever use it or not.
----------------------------------------
From: jann@gmx.de To: telesistant@hotmail.com; app_rpt-users@qrvc.com Subject: Re: [App_rpt-users] CTCSS and carrier squelch Date: Sun, 7 Mar 2010 06:55:47 +0100
Hello Jim,
thank you for the quick response. I did try the new revision 569, but it doesn't work. My config:
hdwtype=0 rxboost=1 rxctcssrelax=1 ;txctcssdefault=71.9
rxctcssfreqs=67.0,71.9,74.4,77.0,79.7,82.5,85.4,88.5,91.5,94.8,97.4,10
0.0,10
3.5,107.2,110.9,114.8,118.8,123.0,127.3,131.8,136.5,141.3,146.2,151.4,
156.7,
162.2,167.9,173.8,179.9,186.2,192.8,203.5,210.7,218.1,225.7,23 3.6,241.8,250.
3
txctcssfreqs=67.0,71.9,74.4,77.0,79.7,82.5,85.4,88.5,91.5,94.8,97.4,10
0.0,10
3.5,107.2,110.9,114.8,118.8,123.0,127.3,131.8,136.5,141.3,146.2,151.4,
156.7,
162.2,167.9,173.8,179.9,186.2,192.8,203.5,210.7,218.1,225.7,23 3.6,241.8,250.
3 rxctcssoverride=1 carrierfrom=dsp ctcssfrom=dsp rxdemod=flat txprelim=yes
The repeater can be opened now without a subtone. Unfortunately subtones will not be detected and regenerated by the repeater or simply passed through the repeater. Any ideas?
Tnx, 73, Jann
-----Original Message----- From: Jim Duuuude [mailto:telesistant@hotmail.com] Sent: Saturday, March 06, 2010 6:05 PM To: Jann; app_rpt mailing list Subject: RE: [App_rpt-users] CTCSS and carrier squelch
A reasonable and easy request. I went to great extremes (sarcasm intended) to make a 1 line change in chan_usbradio to accommodate this need.
A new copy of chan_usbradio.c will be posted to the SVN later today once Steve gets home and does it.
It will add the "rxctcssoverride" parameter to usbradio.conf, allowing the rx CTCSS to default to off. (you have to put "rxctcssoverride = yes" in the file.
You then specify your CTCSS tones like you would normally (as if you were going to require them for access), but the receiver will not require any tone to actually receive.
JIM WB6NIL
----------------------------------------
From: jann@gmx.de To: app_rpt-users@qrvc.com Date: Sat, 6 Mar 2010 17:17:19 +0100 Subject: [App_rpt-users] CTCSS and carrier squelch
Hello,
our repeater is in "carrier squelch"-mode. Since there is much traffic on our repeater we are used to use different subtones for different user groups just for the initial call to request a group member to continue the qso without subtone (so nobody else in the group will be disturbed). Unfortunately this seems to be impossible. We tried these configurations in usbradio.conf:
#1 (we tried "0" in rxctcssfreqs/txctcssfreqs in CTCSS dsp-mode) hdwtype=0 ;txctcssdefault=71.9
rxctcssfreqs=0,67.0,71.9,74.4,77.0,79.7,82.5,85.4,88.5,91.5,94.8,97.4
,
100.0,
103.5,107.2,110.9,114.8,118.8,123.0,127.3,131.8,136.5,141.3,14 6.2,151.4,156.
7,162.2,167.9,173.8,179.9,186.2,192.8,203.5,210.7,218.1,225.7,233.6,2
4
1.8,25 0.3
txctcssfreqs=0,67.0,71.9,74.4,77.0,79.7,82.5,85.4,88.5,91.5,94.8,97.4
,
100.0,
103.5,107.2,110.9,114.8,118.8,123.0,127.3,131.8,136.5,141.3,14 6.2,151.4,156.
7,162.2,167.9,173.8,179.9,186.2,192.8,203.5,210.7,218.1,225.7,233.6,2
4
1.8,25 0.3 carrierfrom=dsp ctcssfrom=dsp rxdemod=flat txprelim=yes
#2 (we tried to disable CTCSS) hdwtype=0 carrierfrom=dsp ctcssfrom=no rxdemod=flat txprelim=yes
Is there a way to pass CTCSS tones through the repeater in "carrier squelch"-mode ? I don't care whether it will be decoded/encoded by the software or just passed through the repeater (0-300 Hz passthrough). Currently passthrough of 0-300 Hz seems to be blocked by the software.
Thanks 73, Jann DG8NGN
-- Jann Traschewski, Drosselstr.1, D-90513 Zirndorf, Germany Tel.: +49-911-696971, Mobile: +49-170-1045937, E-Mail: jann@gmx.de Ham: DG8NGN / DB0VOX, http://www.qsl.net/dg8ngn, ICQ UIN: 4130182
_______________________________________________ App_rpt-users mailing list App_rpt-users@qrvc.com http://qrvc.com/mailman/listinfo/app_rpt-users =
=
I verified your report and indeed it was only putting out the default tone. I located and fixed the problem. You still have to specify a default CTCSS tone (which will be transmitted whether there is an input or not, and whether or not there is CTCSS tone on the input). I just sent the new software to Steve RoDgers and he will put it in SVN later this morning. JIM ----------------------------------------
From: jann@gmx.de To: telesistant@hotmail.com; app_rpt-users@qrvc.com Subject: Re: [App_rpt-users] CTCSS and carrier squelch Date: Sun, 7 Mar 2010 15:57:47 +0100
Hi Jim,
I set 88.5 Hz now as a default CTCSS-tone:
hdwtype=0 rxboost=1 rxctcssrelax=1 txctcssdefault=88.5 rxctcssfreqs=67.0,71.9,74.4,77.0,79.7,82.5,85.4,88.5,91.5,94.8,97.4,100.0,10 3.5,107.2,110.9,114.8,118.8,123.0,127.3,131.8,136.5,141.3,146.2,151.4,156.7, 162.2,167.9,173.8,179.9,186.2,192.8,203.5,210.7,218.1,225.7,233.6,241.8,250. 3 txctcssfreqs=67.0,71.9,74.4,77.0,79.7,82.5,85.4,88.5,91.5,94.8,97.4,100.0,10 3.5,107.2,110.9,114.8,118.8,123.0,127.3,131.8,136.5,141.3,146.2,151.4,156.7, 162.2,167.9,173.8,179.9,186.2,192.8,203.5,210.7,218.1,225.7,233.6,241.8,250. 3 rxctcssoverride=1 carrierfrom=dsp ctcssfrom=dsp rxdemod=flat txprelim=yes
I'm able to open the repeater with any or none subtone. The repeater is sending 88.5 Hz subtone all the time. It doesn't matter which subtone I use on my handheld.
I want the repeater to send out the subtone I use on my handheld, but it doesn't.
I'm currently at the repeaters site and connected to your repeaters. Maybe we can have a short chat on RF.
Thank you, 73, Jann
-----Original Message----- From: Jim Duuuude [mailto:telesistant@hotmail.com] Sent: Sunday, March 07, 2010 3:22 PM To: Jann; app_rpt mailing list Subject: RE: [App_rpt-users] CTCSS and carrier squelch
You have to set a txctcssdefault frequency. If you dont want PL unless someone is encoding it, then include "itxctcss=yes" in app_rpt.c (in the clause for the node), but you still have to specify some tx default frequency whether you ever use it or not.
----------------------------------------
From: jann@gmx.de To: telesistant@hotmail.com; app_rpt-users@qrvc.com Subject: Re: [App_rpt-users] CTCSS and carrier squelch Date: Sun, 7 Mar 2010 06:55:47 +0100
Hello Jim,
thank you for the quick response. I did try the new revision 569, but it doesn't work. My config:
hdwtype=0 rxboost=1 rxctcssrelax=1 ;txctcssdefault=71.9
rxctcssfreqs=67.0,71.9,74.4,77.0,79.7,82.5,85.4,88.5,91.5,94.8,97.4,10
0.0,10
3.5,107.2,110.9,114.8,118.8,123.0,127.3,131.8,136.5,141.3,146.2,151.4,
156.7,
162.2,167.9,173.8,179.9,186.2,192.8,203.5,210.7,218.1,225.7,23 3.6,241.8,250.
3
txctcssfreqs=67.0,71.9,74.4,77.0,79.7,82.5,85.4,88.5,91.5,94.8,97.4,10
0.0,10
3.5,107.2,110.9,114.8,118.8,123.0,127.3,131.8,136.5,141.3,146.2,151.4,
156.7,
162.2,167.9,173.8,179.9,186.2,192.8,203.5,210.7,218.1,225.7,23 3.6,241.8,250.
3 rxctcssoverride=1 carrierfrom=dsp ctcssfrom=dsp rxdemod=flat txprelim=yes
The repeater can be opened now without a subtone. Unfortunately subtones will not be detected and regenerated by the repeater or simply passed through the repeater. Any ideas?
Tnx, 73, Jann
-----Original Message----- From: Jim Duuuude [mailto:telesistant@hotmail.com] Sent: Saturday, March 06, 2010 6:05 PM To: Jann; app_rpt mailing list Subject: RE: [App_rpt-users] CTCSS and carrier squelch
A reasonable and easy request. I went to great extremes (sarcasm intended) to make a 1 line change in chan_usbradio to accommodate this need.
A new copy of chan_usbradio.c will be posted to the SVN later today once Steve gets home and does it.
It will add the "rxctcssoverride" parameter to usbradio.conf, allowing the rx CTCSS to default to off. (you have to put "rxctcssoverride = yes" in the file.
You then specify your CTCSS tones like you would normally (as if you were going to require them for access), but the receiver will not require any tone to actually receive.
JIM WB6NIL
----------------------------------------
From: jann@gmx.de To: app_rpt-users@qrvc.com Date: Sat, 6 Mar 2010 17:17:19 +0100 Subject: [App_rpt-users] CTCSS and carrier squelch
Hello,
our repeater is in "carrier squelch"-mode. Since there is much traffic on our repeater we are used to use different subtones for different user groups just for the initial call to request a group member to continue the qso without subtone (so nobody else in the group will be disturbed). Unfortunately this seems to be impossible. We tried these configurations in usbradio.conf:
#1 (we tried "0" in rxctcssfreqs/txctcssfreqs in CTCSS dsp-mode) hdwtype=0 ;txctcssdefault=71.9
rxctcssfreqs=0,67.0,71.9,74.4,77.0,79.7,82.5,85.4,88.5,91.5,94.8,97.4
,
100.0,
103.5,107.2,110.9,114.8,118.8,123.0,127.3,131.8,136.5,141.3,14 6.2,151.4,156.
7,162.2,167.9,173.8,179.9,186.2,192.8,203.5,210.7,218.1,225.7,233.6,2
4
1.8,25 0.3
txctcssfreqs=0,67.0,71.9,74.4,77.0,79.7,82.5,85.4,88.5,91.5,94.8,97.4
,
100.0,
103.5,107.2,110.9,114.8,118.8,123.0,127.3,131.8,136.5,141.3,14 6.2,151.4,156.
7,162.2,167.9,173.8,179.9,186.2,192.8,203.5,210.7,218.1,225.7,233.6,2
4
1.8,25 0.3 carrierfrom=dsp ctcssfrom=dsp rxdemod=flat txprelim=yes
#2 (we tried to disable CTCSS) hdwtype=0 carrierfrom=dsp ctcssfrom=no rxdemod=flat txprelim=yes
Is there a way to pass CTCSS tones through the repeater in "carrier squelch"-mode ? I don't care whether it will be decoded/encoded by the software or just passed through the repeater (0-300 Hz passthrough). Currently passthrough of 0-300 Hz seems to be blocked by the software.
Thanks 73, Jann DG8NGN
-- Jann Traschewski, Drosselstr.1, D-90513 Zirndorf, Germany Tel.: +49-911-696971, Mobile: +49-170-1045937, E-Mail: jann@gmx.de Ham: DG8NGN / DB0VOX, http://www.qsl.net/dg8ngn, ICQ UIN: 4130182
_______________________________________________ App_rpt-users mailing list App_rpt-users@qrvc.com http://qrvc.com/mailman/listinfo/app_rpt-users =
=
Yeah, that did it ;) Thank you! Since we run two permanently linked repeaters I wonder whether it is possible to "passthrough" the incoming PL not only local but through the other repeater using IAX-protocol? Are there any extensions in IAX that would allow to add some payload like PL-tone-information? That would make it possible to extend our "subtone-user-group-calling" across more repeaters. 73, Jann
-----Original Message----- From: Jim Duuuude [mailto:telesistant@hotmail.com] Sent: Sunday, March 07, 2010 6:45 PM To: Jann; app_rpt mailing list Subject: RE: [App_rpt-users] CTCSS and carrier squelch
I verified your report and indeed it was only putting out the default tone. I located and fixed the problem.
You still have to specify a default CTCSS tone (which will be transmitted whether there is an input or not, and whether or not there is CTCSS tone on the input).
I just sent the new software to Steve RoDgers and he will put it in SVN later this morning.
JIM
----------------------------------------
From: jann@gmx.de To: telesistant@hotmail.com; app_rpt-users@qrvc.com Subject: Re: [App_rpt-users] CTCSS and carrier squelch Date: Sun, 7 Mar 2010 15:57:47 +0100
Hi Jim,
I set 88.5 Hz now as a default CTCSS-tone:
hdwtype=0 rxboost=1 rxctcssrelax=1 txctcssdefault=88.5
rxctcssfreqs=67.0,71.9,74.4,77.0,79.7,82.5,85.4,88.5,91.5,94.8,97.4,10
0.0,10
3.5,107.2,110.9,114.8,118.8,123.0,127.3,131.8,136.5,141.3,146.2,151.4,
156.7,
162.2,167.9,173.8,179.9,186.2,192.8,203.5,210.7,218.1,225.7,23 3.6,241.8,250.
3
txctcssfreqs=67.0,71.9,74.4,77.0,79.7,82.5,85.4,88.5,91.5,94.8,97.4,10
0.0,10
3.5,107.2,110.9,114.8,118.8,123.0,127.3,131.8,136.5,141.3,146.2,151.4,
156.7,
162.2,167.9,173.8,179.9,186.2,192.8,203.5,210.7,218.1,225.7,23 3.6,241.8,250.
3 rxctcssoverride=1 carrierfrom=dsp ctcssfrom=dsp rxdemod=flat txprelim=yes
I'm able to open the repeater with any or none subtone. The repeater is sending 88.5 Hz subtone all the time. It doesn't matter which subtone I use on my handheld.
I want the repeater to send out the subtone I use on my handheld, but it doesn't.
I'm currently at the repeaters site and connected to your repeaters. Maybe we can have a short chat on RF.
Thank you, 73, Jann
-----Original Message----- From: Jim Duuuude [mailto:telesistant@hotmail.com] Sent: Sunday, March 07, 2010 3:22 PM To: Jann; app_rpt mailing list Subject: RE: [App_rpt-users] CTCSS and carrier squelch
You have to set a txctcssdefault frequency. If you dont want PL unless someone is encoding it, then include "itxctcss=yes" in app_rpt.c (in the clause for the node), but you still have to specify some tx default frequency whether you ever use it or not.
----------------------------------------
From: jann@gmx.de To: telesistant@hotmail.com; app_rpt-users@qrvc.com Subject: Re: [App_rpt-users] CTCSS and carrier squelch Date: Sun, 7 Mar 2010 06:55:47 +0100
Hello Jim,
thank you for the quick response. I did try the new revision 569, but it doesn't work. My config:
hdwtype=0 rxboost=1 rxctcssrelax=1 ;txctcssdefault=71.9
rxctcssfreqs=67.0,71.9,74.4,77.0,79.7,82.5,85.4,88.5,91.5,94.8,97.4,1
0
0.0,10
3.5,107.2,110.9,114.8,118.8,123.0,127.3,131.8,136.5,141.3,146.2,151.4
,
156.7,
162.2,167.9,173.8,179.9,186.2,192.8,203.5,210.7,218.1,225.7,23 3.6,241.8,250.
3
txctcssfreqs=67.0,71.9,74.4,77.0,79.7,82.5,85.4,88.5,91.5,94.8,97.4,1
0
0.0,10
3.5,107.2,110.9,114.8,118.8,123.0,127.3,131.8,136.5,141.3,146.2,151.4
,
156.7,
162.2,167.9,173.8,179.9,186.2,192.8,203.5,210.7,218.1,225.7,23 3.6,241.8,250.
3 rxctcssoverride=1 carrierfrom=dsp ctcssfrom=dsp rxdemod=flat txprelim=yes
The repeater can be opened now without a subtone. Unfortunately subtones will not be detected and regenerated by the repeater or simply passed through the repeater. Any ideas?
Tnx, 73, Jann
-----Original Message----- From: Jim Duuuude [mailto:telesistant@hotmail.com] Sent: Saturday, March 06, 2010 6:05 PM To: Jann; app_rpt mailing list Subject: RE: [App_rpt-users] CTCSS and carrier squelch
A reasonable and easy request. I went to great extremes (sarcasm intended) to make a 1 line change in chan_usbradio to accommodate this need.
A new copy of chan_usbradio.c will be posted to the SVN later today once Steve gets home and does it.
It will add the "rxctcssoverride" parameter to usbradio.conf, allowing the rx CTCSS to default to off. (you have to put "rxctcssoverride = yes" in the file.
You then specify your CTCSS tones like you would normally (as if you were going to require them for access), but the receiver will not require any tone to actually receive.
JIM WB6NIL
----------------------------------------
From: jann@gmx.de To: app_rpt-users@qrvc.com Date: Sat, 6 Mar 2010 17:17:19 +0100 Subject: [App_rpt-users] CTCSS and carrier squelch
Hello,
our repeater is in "carrier squelch"-mode. Since there is much traffic on our repeater we are used to use different subtones for different user groups just for the initial call to request a group member to continue the qso without subtone (so nobody else in the group will be disturbed). Unfortunately this seems to be impossible. We tried these configurations in usbradio.conf:
#1 (we tried "0" in rxctcssfreqs/txctcssfreqs in CTCSS dsp-mode) hdwtype=0 ;txctcssdefault=71.9
rxctcssfreqs=0,67.0,71.9,74.4,77.0,79.7,82.5,85.4,88.5,91.5,94.8,97.4
,
100.0,
103.5,107.2,110.9,114.8,118.8,123.0,127.3,131.8,136.5,141.3,14 6.2,151.4,156.
7,162.2,167.9,173.8,179.9,186.2,192.8,203.5,210.7,218.1,225.7,233.6,2
4
1.8,25 0.3
txctcssfreqs=0,67.0,71.9,74.4,77.0,79.7,82.5,85.4,88.5,91.5,94.8,97.4
,
100.0,
103.5,107.2,110.9,114.8,118.8,123.0,127.3,131.8,136.5,141.3,14 6.2,151.4,156.
7,162.2,167.9,173.8,179.9,186.2,192.8,203.5,210.7,218.1,225.7,233.6,2
4
1.8,25 0.3 carrierfrom=dsp ctcssfrom=dsp rxdemod=flat txprelim=yes
#2 (we tried to disable CTCSS) hdwtype=0 carrierfrom=dsp ctcssfrom=no rxdemod=flat txprelim=yes
Is there a way to pass CTCSS tones through the repeater in "carrier squelch"-mode ? I don't care whether it will be decoded/encoded by the software or just passed through the repeater (0-300 Hz passthrough). Currently passthrough of 0-300 Hz seems to be blocked by the software.
Thanks 73, Jann DG8NGN
-- Jann Traschewski, Drosselstr.1, D-90513 Zirndorf, Germany Tel.: +49-911-696971, Mobile: +49-170-1045937, E-Mail: jann@gmx.de Ham: DG8NGN / DB0VOX, http://www.qsl.net/dg8ngn, ICQ UIN: 4130182
_______________________________________________ App_rpt-users mailing list App_rpt-users@qrvc.com http://qrvc.com/mailman/listinfo/app_rpt-users =
=
=
The part regarding sending the CTCSS information in the IAX packet is quite trivial, the problem is that the TX CTCSS selection is not done in app_rpt. Its set and done in chan_usbradio for the USB and in pciradio.c (hardware driver) for the Quad PCI card. There is no direct and easy way to do this the way its done currently and would be quite an undertaking to change it. ----------------------------------------
From: jann@gmx.de To: telesistant@hotmail.com; app_rpt-users@qrvc.com Subject: Re: [App_rpt-users] CTCSS and carrier squelch Date: Mon, 8 Mar 2010 09:58:18 +0100
Yeah, that did it ;) Thank you!
Since we run two permanently linked repeaters I wonder whether it is possible to "passthrough" the incoming PL not only local but through the other repeater using IAX-protocol? Are there any extensions in IAX that would allow to add some payload like PL-tone-information? That would make it possible to extend our "subtone-user-group-calling" across more repeaters.
73, Jann
-----Original Message----- From: Jim Duuuude [mailto:telesistant@hotmail.com] Sent: Sunday, March 07, 2010 6:45 PM To: Jann; app_rpt mailing list Subject: RE: [App_rpt-users] CTCSS and carrier squelch
I verified your report and indeed it was only putting out the default tone. I located and fixed the problem.
You still have to specify a default CTCSS tone (which will be transmitted whether there is an input or not, and whether or not there is CTCSS tone on the input).
I just sent the new software to Steve RoDgers and he will put it in SVN later this morning.
JIM
----------------------------------------
From: jann@gmx.de To: telesistant@hotmail.com; app_rpt-users@qrvc.com Subject: Re: [App_rpt-users] CTCSS and carrier squelch Date: Sun, 7 Mar 2010 15:57:47 +0100
Hi Jim,
I set 88.5 Hz now as a default CTCSS-tone:
hdwtype=0 rxboost=1 rxctcssrelax=1 txctcssdefault=88.5
rxctcssfreqs=67.0,71.9,74.4,77.0,79.7,82.5,85.4,88.5,91.5,94.8,97.4,10
0.0,10
3.5,107.2,110.9,114.8,118.8,123.0,127.3,131.8,136.5,141.3,146.2,151.4,
156.7,
162.2,167.9,173.8,179.9,186.2,192.8,203.5,210.7,218.1,225.7,23 3.6,241.8,250.
3
txctcssfreqs=67.0,71.9,74.4,77.0,79.7,82.5,85.4,88.5,91.5,94.8,97.4,10
0.0,10
3.5,107.2,110.9,114.8,118.8,123.0,127.3,131.8,136.5,141.3,146.2,151.4,
156.7,
162.2,167.9,173.8,179.9,186.2,192.8,203.5,210.7,218.1,225.7,23 3.6,241.8,250.
3 rxctcssoverride=1 carrierfrom=dsp ctcssfrom=dsp rxdemod=flat txprelim=yes
I'm able to open the repeater with any or none subtone. The repeater is sending 88.5 Hz subtone all the time. It doesn't matter which subtone I use on my handheld.
I want the repeater to send out the subtone I use on my handheld, but it doesn't.
I'm currently at the repeaters site and connected to your repeaters. Maybe we can have a short chat on RF.
Thank you, 73, Jann
-----Original Message----- From: Jim Duuuude [mailto:telesistant@hotmail.com] Sent: Sunday, March 07, 2010 3:22 PM To: Jann; app_rpt mailing list Subject: RE: [App_rpt-users] CTCSS and carrier squelch
You have to set a txctcssdefault frequency. If you dont want PL unless someone is encoding it, then include "itxctcss=yes" in app_rpt.c (in the clause for the node), but you still have to specify some tx default frequency whether you ever use it or not.
----------------------------------------
From: jann@gmx.de To: telesistant@hotmail.com; app_rpt-users@qrvc.com Subject: Re: [App_rpt-users] CTCSS and carrier squelch Date: Sun, 7 Mar 2010 06:55:47 +0100
Hello Jim,
thank you for the quick response. I did try the new revision 569, but it doesn't work. My config:
hdwtype=0 rxboost=1 rxctcssrelax=1 ;txctcssdefault=71.9
rxctcssfreqs=67.0,71.9,74.4,77.0,79.7,82.5,85.4,88.5,91.5,94.8,97.4,1
0
0.0,10
3.5,107.2,110.9,114.8,118.8,123.0,127.3,131.8,136.5,141.3,146.2,151.4
,
156.7,
162.2,167.9,173.8,179.9,186.2,192.8,203.5,210.7,218.1,225.7,23 3.6,241.8,250.
3
txctcssfreqs=67.0,71.9,74.4,77.0,79.7,82.5,85.4,88.5,91.5,94.8,97.4,1
0
0.0,10
3.5,107.2,110.9,114.8,118.8,123.0,127.3,131.8,136.5,141.3,146.2,151.4
,
156.7,
162.2,167.9,173.8,179.9,186.2,192.8,203.5,210.7,218.1,225.7,23 3.6,241.8,250.
3 rxctcssoverride=1 carrierfrom=dsp ctcssfrom=dsp rxdemod=flat txprelim=yes
The repeater can be opened now without a subtone. Unfortunately subtones will not be detected and regenerated by the repeater or simply passed through the repeater. Any ideas?
Tnx, 73, Jann
-----Original Message----- From: Jim Duuuude [mailto:telesistant@hotmail.com] Sent: Saturday, March 06, 2010 6:05 PM To: Jann; app_rpt mailing list Subject: RE: [App_rpt-users] CTCSS and carrier squelch
A reasonable and easy request. I went to great extremes (sarcasm intended) to make a 1 line change in chan_usbradio to accommodate this need.
A new copy of chan_usbradio.c will be posted to the SVN later today once Steve gets home and does it.
It will add the "rxctcssoverride" parameter to usbradio.conf, allowing the rx CTCSS to default to off. (you have to put "rxctcssoverride = yes" in the file.
You then specify your CTCSS tones like you would normally (as if you were going to require them for access), but the receiver will not require any tone to actually receive.
JIM WB6NIL
----------------------------------------
From: jann@gmx.de To: app_rpt-users@qrvc.com Date: Sat, 6 Mar 2010 17:17:19 +0100 Subject: [App_rpt-users] CTCSS and carrier squelch
Hello,
our repeater is in "carrier squelch"-mode. Since there is much traffic on our repeater we are used to use different subtones for different user groups just for the initial call to request a group member to continue the qso without subtone (so nobody else in the group will be disturbed). Unfortunately this seems to be impossible. We tried these configurations in usbradio.conf:
#1 (we tried "0" in rxctcssfreqs/txctcssfreqs in CTCSS dsp-mode) hdwtype=0 ;txctcssdefault=71.9
rxctcssfreqs=0,67.0,71.9,74.4,77.0,79.7,82.5,85.4,88.5,91.5,94.8,97.4
,
100.0,
103.5,107.2,110.9,114.8,118.8,123.0,127.3,131.8,136.5,141.3,14 6.2,151.4,156.
7,162.2,167.9,173.8,179.9,186.2,192.8,203.5,210.7,218.1,225.7,233.6,2
4
1.8,25 0.3
txctcssfreqs=0,67.0,71.9,74.4,77.0,79.7,82.5,85.4,88.5,91.5,94.8,97.4
,
100.0,
103.5,107.2,110.9,114.8,118.8,123.0,127.3,131.8,136.5,141.3,14 6.2,151.4,156.
7,162.2,167.9,173.8,179.9,186.2,192.8,203.5,210.7,218.1,225.7,233.6,2
4
1.8,25 0.3 carrierfrom=dsp ctcssfrom=dsp rxdemod=flat txprelim=yes
#2 (we tried to disable CTCSS) hdwtype=0 carrierfrom=dsp ctcssfrom=no rxdemod=flat txprelim=yes
Is there a way to pass CTCSS tones through the repeater in "carrier squelch"-mode ? I don't care whether it will be decoded/encoded by the software or just passed through the repeater (0-300 Hz passthrough). Currently passthrough of 0-300 Hz seems to be blocked by the software.
Thanks 73, Jann DG8NGN
-- Jann Traschewski, Drosselstr.1, D-90513 Zirndorf, Germany Tel.: +49-911-696971, Mobile: +49-170-1045937, E-Mail: jann@gmx.de Ham: DG8NGN / DB0VOX, http://www.qsl.net/dg8ngn, ICQ UIN: 4130182
_______________________________________________ App_rpt-users mailing list App_rpt-users@qrvc.com http://qrvc.com/mailman/listinfo/app_rpt-users =
=
=
and, by the way, its xpmr.c and xpmr.h in the channels/xpmr directory ----------------------------------------
From: jann@gmx.de To: telesistant@hotmail.com; app_rpt-users@qrvc.com Subject: Re: [App_rpt-users] CTCSS and carrier squelch Date: Sun, 7 Mar 2010 15:57:47 +0100
Hi Jim,
I set 88.5 Hz now as a default CTCSS-tone:
hdwtype=0 rxboost=1 rxctcssrelax=1 txctcssdefault=88.5 rxctcssfreqs=67.0,71.9,74.4,77.0,79.7,82.5,85.4,88.5,91.5,94.8,97.4,100.0,10 3.5,107.2,110.9,114.8,118.8,123.0,127.3,131.8,136.5,141.3,146.2,151.4,156.7, 162.2,167.9,173.8,179.9,186.2,192.8,203.5,210.7,218.1,225.7,233.6,241.8,250. 3 txctcssfreqs=67.0,71.9,74.4,77.0,79.7,82.5,85.4,88.5,91.5,94.8,97.4,100.0,10 3.5,107.2,110.9,114.8,118.8,123.0,127.3,131.8,136.5,141.3,146.2,151.4,156.7, 162.2,167.9,173.8,179.9,186.2,192.8,203.5,210.7,218.1,225.7,233.6,241.8,250. 3 rxctcssoverride=1 carrierfrom=dsp ctcssfrom=dsp rxdemod=flat txprelim=yes
I'm able to open the repeater with any or none subtone. The repeater is sending 88.5 Hz subtone all the time. It doesn't matter which subtone I use on my handheld.
I want the repeater to send out the subtone I use on my handheld, but it doesn't.
I'm currently at the repeaters site and connected to your repeaters. Maybe we can have a short chat on RF.
Thank you, 73, Jann
-----Original Message----- From: Jim Duuuude [mailto:telesistant@hotmail.com] Sent: Sunday, March 07, 2010 3:22 PM To: Jann; app_rpt mailing list Subject: RE: [App_rpt-users] CTCSS and carrier squelch
You have to set a txctcssdefault frequency. If you dont want PL unless someone is encoding it, then include "itxctcss=yes" in app_rpt.c (in the clause for the node), but you still have to specify some tx default frequency whether you ever use it or not.
----------------------------------------
From: jann@gmx.de To: telesistant@hotmail.com; app_rpt-users@qrvc.com Subject: Re: [App_rpt-users] CTCSS and carrier squelch Date: Sun, 7 Mar 2010 06:55:47 +0100
Hello Jim,
thank you for the quick response. I did try the new revision 569, but it doesn't work. My config:
hdwtype=0 rxboost=1 rxctcssrelax=1 ;txctcssdefault=71.9
rxctcssfreqs=67.0,71.9,74.4,77.0,79.7,82.5,85.4,88.5,91.5,94.8,97.4,10
0.0,10
3.5,107.2,110.9,114.8,118.8,123.0,127.3,131.8,136.5,141.3,146.2,151.4,
156.7,
162.2,167.9,173.8,179.9,186.2,192.8,203.5,210.7,218.1,225.7,23 3.6,241.8,250.
3
txctcssfreqs=67.0,71.9,74.4,77.0,79.7,82.5,85.4,88.5,91.5,94.8,97.4,10
0.0,10
3.5,107.2,110.9,114.8,118.8,123.0,127.3,131.8,136.5,141.3,146.2,151.4,
156.7,
162.2,167.9,173.8,179.9,186.2,192.8,203.5,210.7,218.1,225.7,23 3.6,241.8,250.
3 rxctcssoverride=1 carrierfrom=dsp ctcssfrom=dsp rxdemod=flat txprelim=yes
The repeater can be opened now without a subtone. Unfortunately subtones will not be detected and regenerated by the repeater or simply passed through the repeater. Any ideas?
Tnx, 73, Jann
-----Original Message----- From: Jim Duuuude [mailto:telesistant@hotmail.com] Sent: Saturday, March 06, 2010 6:05 PM To: Jann; app_rpt mailing list Subject: RE: [App_rpt-users] CTCSS and carrier squelch
A reasonable and easy request. I went to great extremes (sarcasm intended) to make a 1 line change in chan_usbradio to accommodate this need.
A new copy of chan_usbradio.c will be posted to the SVN later today once Steve gets home and does it.
It will add the "rxctcssoverride" parameter to usbradio.conf, allowing the rx CTCSS to default to off. (you have to put "rxctcssoverride = yes" in the file.
You then specify your CTCSS tones like you would normally (as if you were going to require them for access), but the receiver will not require any tone to actually receive.
JIM WB6NIL
----------------------------------------
From: jann@gmx.de To: app_rpt-users@qrvc.com Date: Sat, 6 Mar 2010 17:17:19 +0100 Subject: [App_rpt-users] CTCSS and carrier squelch
Hello,
our repeater is in "carrier squelch"-mode. Since there is much traffic on our repeater we are used to use different subtones for different user groups just for the initial call to request a group member to continue the qso without subtone (so nobody else in the group will be disturbed). Unfortunately this seems to be impossible. We tried these configurations in usbradio.conf:
#1 (we tried "0" in rxctcssfreqs/txctcssfreqs in CTCSS dsp-mode) hdwtype=0 ;txctcssdefault=71.9
rxctcssfreqs=0,67.0,71.9,74.4,77.0,79.7,82.5,85.4,88.5,91.5,94.8,97.4
,
100.0,
103.5,107.2,110.9,114.8,118.8,123.0,127.3,131.8,136.5,141.3,14 6.2,151.4,156.
7,162.2,167.9,173.8,179.9,186.2,192.8,203.5,210.7,218.1,225.7,233.6,2
4
1.8,25 0.3
txctcssfreqs=0,67.0,71.9,74.4,77.0,79.7,82.5,85.4,88.5,91.5,94.8,97.4
,
100.0,
103.5,107.2,110.9,114.8,118.8,123.0,127.3,131.8,136.5,141.3,14 6.2,151.4,156.
7,162.2,167.9,173.8,179.9,186.2,192.8,203.5,210.7,218.1,225.7,233.6,2
4
1.8,25 0.3 carrierfrom=dsp ctcssfrom=dsp rxdemod=flat txprelim=yes
#2 (we tried to disable CTCSS) hdwtype=0 carrierfrom=dsp ctcssfrom=no rxdemod=flat txprelim=yes
Is there a way to pass CTCSS tones through the repeater in "carrier squelch"-mode ? I don't care whether it will be decoded/encoded by the software or just passed through the repeater (0-300 Hz passthrough). Currently passthrough of 0-300 Hz seems to be blocked by the software.
Thanks 73, Jann DG8NGN
-- Jann Traschewski, Drosselstr.1, D-90513 Zirndorf, Germany Tel.: +49-911-696971, Mobile: +49-170-1045937, E-Mail: jann@gmx.de Ham: DG8NGN / DB0VOX, http://www.qsl.net/dg8ngn, ICQ UIN: 4130182
_______________________________________________ App_rpt-users mailing list App_rpt-users@qrvc.com http://qrvc.com/mailman/listinfo/app_rpt-users =
=
participants (3)
-
Jann Traschewski -
Jim Duuuude -
Ralph A. Schmid, dk5ras