Is there a squelch tail eliminator setting for ACID in the full duplex mode?
There is for TX (mobile RX) if using the RTCM for your radio interface. In that case the setting is in the RTCM. If other interfaces support STE I am not aware of it. -- Tim :wq On Jul 23, 2013, at 8:58 AM, Johnny Keeker <cypresstower@yahoo.com> wrote:
Is there a squelch tail eliminator setting for ACID in the full duplex mode? _______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
Use radio tune rxsquelch to set the squelch. In ACID: AST_2249_XCN*CLI> radio tune rxsquelch Current Signal Strength is 741 Current Squelch setting is 501 If the setting is lower then you will hear squelch crash. Set the squelch above the measured level: AST_2249_XCN*CLI> radio tune rxsquelch 800 Changed Squelch setting to 800 AST_2249_XCN*CLI> radio tune rxsquelch Current Signal Strength is 749 Current Squelch setting is 800 AST_2249_XCN*CLI> Then do a "radio tune save" to save the setting. The squelch should now close very fast like the Micor squelch. It works very well. Jon VA3RQ On 7/23/2013 12:43 PM, Tim Sawyer wrote:
There is for TX (mobile RX) if using the RTCM for your radio interface. In that case the setting is in the RTCM.
If other interfaces support STE I am not aware of it. -- Tim :wq
On Jul 23, 2013, at 8:58 AM, Johnny Keeker <cypresstower@yahoo.com <mailto:cypresstower@yahoo.com>> wrote:
Is there a squelch tail eliminator setting for ACID in the full duplex mode? _______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org <mailto:App_rpt-users@ohnosec.org> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
Jon I ran your setup, the numbers were different but it helped a lot. Browsing the chan_usbradio.c file, I found a line in the code "int rxsquelchdelay" in and among other function of the usbradio stanza, so I added it the usbradio.conf file as follows rxsquelchdelay=90 After a restart the squelch tail was completely gone. Can you or anyone shed some light on this? ________________________________ From: Jon Rorke <jrorke@cogeco.ca> To: Cc: "app_rpt-users@ohnosec.org" <app_rpt-users@ohnosec.org> Sent: Tuesday, July 23, 2013 2:28 PM Subject: Re: [App_rpt-users] Squlech Tail Use radio tune rxsquelch to set the squelch. In ACID: AST_2249_XCN*CLI> radio tune rxsquelch Current Signal Strength is 741 Current Squelch setting is 501 If the setting is lower then you will hear squelch crash. Set the squelch above the measured level: AST_2249_XCN*CLI> radio tune rxsquelch 800 Changed Squelch setting to 800 AST_2249_XCN*CLI> radio tune rxsquelch Current Signal Strength is 749 Current Squelch setting is 800 AST_2249_XCN*CLI> Then do a "radio tune save" to save the setting. The squelch should now close very fast like the Micor squelch. It works very well. Jon VA3RQ On 7/23/2013 12:43 PM, Tim Sawyer wrote: There is for TX (mobile RX) if using the RTCM for your radio interface. In that case the setting is in the RTCM.
If other interfaces support STE I am not aware of it.
-- Tim :wq
On Jul 23, 2013, at 8:58 AM, Johnny Keeker <cypresstower@yahoo.com> wrote:
Is there a squelch tail eliminator setting for ACID in the full duplex mode?_______________________________________________
App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
_______________________________________________
App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users _______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
In usbradio.conf rxsquelchdelay=100 ; squelch tail eliminator - NEW only works with DSP Ken From: Johnny Keeker [mailto:cypresstower@yahoo.com] Sent: Tuesday, July 23, 2013 11:59 AM To: app_rpt-users@ohnosec.org Subject: Re: [App_rpt-users] Squlech Tail Is there a squelch tail eliminator setting for ACID in the full duplex mode?
participants (4)
-
Johnny Keeker -
Jon Rorke -
Ken -
Tim Sawyer