I seem to recall discussion of a setting that transmits CTCSS only when local repeater input or linked audio is being transmitted, and does not for ID, courtesy tone, etc. I've looked through the archives but have not found anything. I may just be confusing it with features of some other controllers. The reason I ask is a recent discussion on the other list ended with the answer of being unable to do it since there is not any code in all of asterisk/app_rpt to handle it. Thanks, Brett KQ9N
On Wed, Jun 21, 2017 at 7:39 AM, Brett Friermood <brett.friermood@gmail.com> wrote:
I seem to recall discussion of a setting that transmits CTCSS only when local repeater input or linked audio is being transmitted, and does not for ID, courtesy tone, etc. I've looked through the archives but have not found anything. I may just be confusing it with features of some other controllers.
The reason I ask is a recent discussion on the other list ended with the answer of being unable to do it since there is not any code in all of asterisk/app_rpt to handle it.
Brett, I found a hint that this may have been more than a feature request at one point. Check this out: https://github.com/N4IRS/AllStar/blob/c1390b4fe726c544c9f3e8111d6d6acc31f266... 958 = cop.58 ; Tx CTCSS On Input only Enable 959 = cop,59 ; Tx CTCSS On Input only Disable cop.58 [sic] and cop,59. Do these actually trigger relevant code or is it a dead-end? Tom KD7LXL
A better place to look on github is the AllStarLink repository. The N4IRS/AllStar is a leftover. The DIAL installer is at: <https://github.com/AllStarLink/DIAL> The config files for DIAL were populated from the source. It is a attempt to capture and documentall the commands and config variables. That being said, I remember a discussion I had with Jim about Which radio interfaces and channel drivers would support it. If anything supported the function it would be chan_usbradio and the PCI card. Not simpleusb. When I get a chance, I'll look at it since Mike and I are spending some time in the channel drivers. 73, Steve N4IRS On 8/4/2017 11:36 AM, Tom Hayward wrote:
On Wed, Jun 21, 2017 at 7:39 AM, Brett Friermood <brett.friermood@gmail.com> wrote:
I seem to recall discussion of a setting that transmits CTCSS only when local repeater input or linked audio is being transmitted, and does not for ID, courtesy tone, etc. I've looked through the archives but have not found anything. I may just be confusing it with features of some other controllers.
The reason I ask is a recent discussion on the other list ended with the answer of being unable to do it since there is not any code in all of asterisk/app_rpt to handle it. Brett,
I found a hint that this may have been more than a feature request at one point. Check this out: https://github.com/N4IRS/AllStar/blob/c1390b4fe726c544c9f3e8111d6d6acc31f266... 958 = cop.58 ; Tx CTCSS On Input only Enable 959 = cop,59 ; Tx CTCSS On Input only Disable
cop.58 [sic] and cop,59. Do these actually trigger relevant code or is it a dead-end?
Tom KD7LXL _______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
On Fri, Aug 4, 2017 at 8:57 AM, Steve Zingman <szingman@msgstor.com> wrote:
A better place to look on github is the AllStarLink repository. The N4IRS/AllStar is a leftover. The DIAL installer is at: <https://github.com/AllStarLink/DIAL>
Steve, I am emailing faster than I am grepping. :-) I found where it sends this command to the channel driver: https://github.com/AllStarLink/Asterisk/blob/master/asterisk/apps/app_rpt.c#... I will look in the channel drivers next to see if the command is ever acted on... Tom KD7LXL
On Fri, Aug 4, 2017 at 9:03 AM, Tom Hayward <tom@tomh.us> wrote:
Steve, I am emailing faster than I am grepping. :-)
I found where it sends this command to the channel driver: https://github.com/AllStarLink/Asterisk/blob/master/asterisk/apps/app_rpt.c#...
I will look in the channel drivers next to see if the command is ever acted on...
Okay, this should be the last one. I found where the command is received in usbradio. I did not find any section in simpleusb that acts on this command. https://github.com/AllStarLink/Asterisk/blob/20800a2f8480cd31f236ed1dba904a1... You would enable this permanently by adding the following to rpt.conf: itxctcss = 1 Tom KD7LXL
On 8/4/17 11:57 AM, Steve Zingman wrote:
If anything supported the function it would be chan_usbradio and the PCI card. Not simpleusb.
Could we have an easy way to do this via GPIO on simpleusb? The PCIradio has a couple GPIO pins that would be able to go high/low to disable/enable PL on transmit if the transmitter so supported it. -- Bryan Fields 727-409-1194 - Voice http://bryanfields.net
participants (4)
-
Brett Friermood -
Bryan Fields -
Steve Zingman -
Tom Hayward