Re: [App_rpt-users] Motorola CDM1250 JU551 position B
which takes even LESS time....;) -- Bryan Sent from my iPhone 6S...No electrons were harmed in the sending of this message.
On Jan 8, 2019, at 12:27, Scott Zimmerman <n3xcc@repeater-builder.com> wrote:
Take longer to wire the cable up than to get the sw working, in my experience. That's why I made a radio interface that plugs directly into the back of the radio. ;)
Check out the RIM_Maxtrac: http://www.repeater-builder.com/products/usb-rim-lite.html
Scott
Scott Zimmerman Amateur Radio Call N3XCC 474 Barnett Road Boswell, PA 15531
On 1/7/2019 9:39 PM, Bryan D. Boyle wrote: CDMs are stupid simple to connect to a URI. Just need discriminator rx audio, ground, xmit flat audio, and ptt. IIRC, rear connector pins 3, 5, 7, 11 (check the multitude of online sites for the specifics, but this is what I recall) set up radio in CPS to send the right signals to the right pins, turn off pre/deemphasis in radio, do all the rest (COS, pl decode/encode, de/preemphasis, etc) in asterisk. log in, radio-tune-menu to set levels and squelch, you are good to go. Take longer to wire the cable up than to get the sw working, in my experience. Simplest and fastest way. -- Bryan Sent from my iPhone 6S...No electrons were harmed in the sending of this message.
On Jan 7, 2019, at 14:40, Corey Dean <n3fe@repeater.net <mailto:n3fe@repeater.net>> wrote: Mike is correct. This is all controlled in the cps.
Corey n3fe
On Mon, Jan 7, 2019 at 2:33 PM Mike Lee <ksixmju@gmail.com <mailto:ksixmju@gmail.com>> wrote:
There are no physical jumpers in the CDM series (750/1250/1550) of radios.
The GM300 is the radio that has the JU551; it controls de-emphasis.
Mike
On Mon, Jan 7, 2019 at 11:25 AM w4ram@outlook.com <mailto:w4ram@outlook.com> <w4ram@outlook.com <mailto:w4ram@outlook.com>> wrote:
Good morning,
I am using a Motorola CDM1250 for my node. I am using the DMK URI. I am wondering if is necessarry change de JU551
switch to position B as is recommended to be able to use this radio properly.
Thank you for your assistance.
Al W4RAM _______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org <mailto:App_rpt-users@lists.allstarlink.org> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and
scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
App_rpt-users mailing list App_rpt-users@lists.allstarlink.org <mailto:App_rpt-users@lists.allstarlink.org> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org <mailto:App_rpt-users@lists.allstarlink.org> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
participants (1)
-
Bryan D. Boyle