Re: [App_rpt-users] Kernel Headers for RaspberryPi Stretch Image
Got that done, but now having no luck getting the Pi 3B+ to connect to WLAN. Worked fine with the GUI, but CLI isn't connecting. Looks like lots of folks are having issues with the 3B+ connecting to WLAN via CLI. Tried most everything I've seen on the 'net; open to suggestions. Mike WM4B -----Original Message----- From: App_rpt-users [mailto:app_rpt-users-bounces@lists.allstarlink.org] On Behalf Of Steve Zingman Sent: Thursday, May 24, 2018 9:25 PM To: app_rpt-users@lists.allstarlink.org Subject: Re: [App_rpt-users] Kernel Headers for RaspberryPi Stretch Image Then simply install <http://dvswitch.org/files/ASL_Images/Raspberry_Pi/Stretch/ASL_1.01-20180228-armhf-raspbian-stretch-image.zip> Follow the included readme. Steve On 05/24/2018 09:21 PM, Mike Besemer wrote:
Sorry Steve... should have mentioned that.
This is my initial setup for the Pi (and my first node), so I burned the Raspian Stretch image to an SD card and then followed the instructions in the readme file I mentioned below.
I can navigate the command line ok, but at this point I'm just following instructions as I find them. From what I gathered, the image at dvswitch.org had headers which were too new and I needed to install older versions - or at least that my interpretation of the instructions. At any rate, everything describe below worked as advertised, but when I did the reboot, I got the message that said Raspian had been updated to the latest version. I'm wondering if that overwrote the older kernel headers I'd just installed.
If I'm barking up the wrong tree, I don't mind regrouping... I don't have much time invested so far and this project is more about learning than it is about the final product. To me, it seems like the things that are needed to get from zero to a working node are kind of scattered, and I'm struggling a bit with that... mostly because I can't sit for an hour or two at time to work on it right now.
If you can lead, I'll follow!
73,
Mike WM4B
-----Original Message----- From: App_rpt-users [mailto:app_rpt-users-bounces@lists.allstarlink.org] On Behalf Of Steve Zingman Sent: Thursday, May 24, 2018 7:49 PM To: app_rpt-users@lists.allstarlink.org Subject: Re: [App_rpt-users] Kernel Headers for RaspberryPi Stretch Image
Mike, What is it you are trying to do?
Steve N4IRS
On 05/24/2018 05:30 PM, Mike Besemer wrote:
Got the Raspbian Stretch image installed to my Pi 3B and followed the directions (below) from the readme file at: <http://dvswitch.org/files/ASL_Images/Raspberry_Pi/Stretch/2018-03-13-raspbi an-stretch.readme>:
"This is the last Raspbian Stretch version that supports OSS which is required for AllStarLink. When Raspbian installs the kernel headers, again required for AllStarLink, it installs the latest, NOT the kernel headers for the running kernel.
To add the proper kernel headers to the Stretch image, you should do the following as root:
cd /tmp wget http://dvswitch.org/files/ASL_Images/Raspberry_Pi/Stretch/raspberrypi-kernel -headers_1.20171029-1_armhf.deb dpkg -i raspberrypi-kernel-headers_1.20171029-1_armhf.deb
Once this completes: apt-mark hold raspberrypi-kernel-headers raspberrypi-kernel apt-get update apt-get upgrade -y
reboot"
All of this seemed to go as expected, but when I rebooted, I received a notice that the latest image had been installed. Did that just undo the changes I made above? If so, how do I prevent that from happening?
Sorry, I'm not a Linux guy; just trying to muddle through.
73,
Mike WM4B
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
As root or sudo -s raspi-config NetWork Options WiFi On 05/26/2018 01:59 PM, Mike Besemer wrote:
Got that done, but now having no luck getting the Pi 3B+ to connect to WLAN. Worked fine with the GUI, but CLI isn't connecting. Looks like lots of folks are having issues with the 3B+ connecting to WLAN via CLI. Tried most everything I've seen on the 'net; open to suggestions.
Mike WM4B
-----Original Message----- From: App_rpt-users [mailto:app_rpt-users-bounces@lists.allstarlink.org] On Behalf Of Steve Zingman Sent: Thursday, May 24, 2018 9:25 PM To: app_rpt-users@lists.allstarlink.org Subject: Re: [App_rpt-users] Kernel Headers for RaspberryPi Stretch Image
Then simply install <http://dvswitch.org/files/ASL_Images/Raspberry_Pi/Stretch/ASL_1.01-20180228-armhf-raspbian-stretch-image.zip> Follow the included readme.
Steve
On 05/24/2018 09:21 PM, Mike Besemer wrote:
Sorry Steve... should have mentioned that.
This is my initial setup for the Pi (and my first node), so I burned the Raspian Stretch image to an SD card and then followed the instructions in the readme file I mentioned below.
I can navigate the command line ok, but at this point I'm just following instructions as I find them. From what I gathered, the image at dvswitch.org had headers which were too new and I needed to install older versions - or at least that my interpretation of the instructions. At any rate, everything describe below worked as advertised, but when I did the reboot, I got the message that said Raspian had been updated to the latest version. I'm wondering if that overwrote the older kernel headers I'd just installed.
If I'm barking up the wrong tree, I don't mind regrouping... I don't have much time invested so far and this project is more about learning than it is about the final product. To me, it seems like the things that are needed to get from zero to a working node are kind of scattered, and I'm struggling a bit with that... mostly because I can't sit for an hour or two at time to work on it right now.
If you can lead, I'll follow!
73,
Mike WM4B
-----Original Message----- From: App_rpt-users [mailto:app_rpt-users-bounces@lists.allstarlink.org] On Behalf Of Steve Zingman Sent: Thursday, May 24, 2018 7:49 PM To: app_rpt-users@lists.allstarlink.org Subject: Re: [App_rpt-users] Kernel Headers for RaspberryPi Stretch Image
Mike, What is it you are trying to do?
Steve N4IRS
On 05/24/2018 05:30 PM, Mike Besemer wrote:
Got the Raspbian Stretch image installed to my Pi 3B and followed the directions (below) from the readme file at: <http://dvswitch.org/files/ASL_Images/Raspberry_Pi/Stretch/2018-03-13-raspbi an-stretch.readme>:
"This is the last Raspbian Stretch version that supports OSS which is required for AllStarLink. When Raspbian installs the kernel headers, again required for AllStarLink, it installs the latest, NOT the kernel headers for the running kernel.
To add the proper kernel headers to the Stretch image, you should do the following as root:
cd /tmp wget http://dvswitch.org/files/ASL_Images/Raspberry_Pi/Stretch/raspberrypi-kernel -headers_1.20171029-1_armhf.deb dpkg -i raspberrypi-kernel-headers_1.20171029-1_armhf.deb
Once this completes: apt-mark hold raspberrypi-kernel-headers raspberrypi-kernel apt-get update apt-get upgrade -y
reboot"
All of this seemed to go as expected, but when I rebooted, I received a notice that the latest image had been installed. Did that just undo the changes I made above? If so, how do I prevent that from happening?
Sorry, I'm not a Linux guy; just trying to muddle through.
73,
Mike WM4B
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
participants (2)
-
Mike Besemer -
Steve Zingman