[Allstar Digital] DMRGateway

[Steve Zingman]

set dmrlink.cfg to INFO and output to console
start ambe_audio.py in the foreground.
Talk on repeater
What do you get on the screen?
copy and paste it to message.

On 01/29/2016 09:32 PM, Robert Newberry wrote:
>
> So I looked a DMRGateway.ini under /etc. The ports match what I see in 
> DMRGateway.pdf. All of the IPs are 127.0.0.1 which I believe is correct.
>
> I confirmed that AMBEserverGPIO is running.
>
> As far as I know to test this I go to /opt/dmrlink/ambe_audio  then 
> type python ambe_audio.py
>
> If Everything is right, I should hear myself in my node. I am 
> connected to my node using iaxrpt.
>
> In ambe_audio.cfg what is the remote control port? Default is 1235 the 
> gateway port is 1234 which I think is the port between dmrlink and 
> dmrgateway.
>
> N1XBM
> Apparare Scientor
> Paratus Communicare
> Allstar Node # 27086, 41540, 41812, 42086, 42658
>
> On Jan 29, 2016 5:43 AM, "Steve Zingman" <szingman at msgstor.com 
> <mailto:szingman at msgstor.com>> wrote:
>
>     Is AMBEserverGPIO running? Have you tested it for proper operation?
>     is DMRGateway running? Are the settings in DMRGateway.ini correct?
>
>
>
>
>     On 01/28/2016 10:16 PM, Robert Newberry wrote:
>>     So I followed instructions from previous emails.
>>
>>     I first went to my rpt.conf and did this
>>
>>     rxchannel = usrp/127.0.0.1:34001:32001
>>
>>     Then
>>
>>     Configure dmrlink.cfg in /opt/dmrlink/ambe_audio as a master
>>         Configure the repeater to point at the Pi as a peer.
>>             cd /opt/dmrlink/ambe_audio
>>             Test it by running python dmrlink.py in ambe_audio Watch
>>     the log
>>         stop dmrlink.py
>>         If you have rebooted DMRGateway should be running.
>>             Check it with ps ax | grep DMRGateway
>>                 If not start it with /usr/local/bin/DMRGateway &
>>             Make sure asterisk is running and connect a node to it so
>>     you can hear it.
>>         start python ambe_audio.py
>>
>>     Everything looks OK on the output, other than not hearing myself.
>>     I am also using TS2 TG2 which by the looks of the default
>>     ambe_audio.cfg in /opt/dmrlink/ambe_audio has TG2 in the filter.
>>
>>     Is there any other ports I need to set? It looks like most things
>>     are set default.
>>
>>
>>
>>     _______________________________________________
>>     Allstar-Digital mailing list
>>     Allstar-Digital at lists.keekles.org
>>     <mailto:Allstar-Digital at lists.keekles.org>
>>     http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
>
>     -- 
>     "Anything is possible if you don't know what you are talking about."
>     1st Law of Logic
>
>
>     _______________________________________________
>     Allstar-Digital mailing list
>     Allstar-Digital at lists.keekles.org
>     <mailto:Allstar-Digital at lists.keekles.org>
>     http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
>
>
>
> _______________________________________________
> Allstar-Digital mailing list
> Allstar-Digital at lists.keekles.org
> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital

-- 
"Anything is possible if you don't know what you are talking about."
1st Law of Logic

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.allstarlink.org/pipermail/allstar-digital/attachments/20160129/232cd5a0/attachment.html>