[Allstar Digital] DMRGateway

[Robert Newberry]

root at repeater:/opt/dmrlink/ambe_audio# python ambe_audio.py
INFO DMRlink 'ambe_audio.py' (c) 2015 N0MJS & the K0USY Group - SYSTEM
STARTING...
INFO (N1XBM_MASTER) IPSC Instance Created: 54321, 0.0.0.0:50001
DMRLink ambe server
Send UDP frames to DMR gateway 127.0.0.1:1234
Remote control is listening on: repeater 1235
INFO (N1XBM_MASTER) Master Registration Packet Received from peer 312307,
192.168.0.202:50002
Voice Transmission Start on TS 2 and TG Local (2) from N1XBM
Voice Transmission End 5.22 seconds


On Fri, Jan 29, 2016 at 9:36 PM, Steve Zingman <szingman at msgstor.com> wrote:

> set dmrlink.cfg to INFO and output to console
> start ambe_audio.py in the foreground.
> Talk on repeater
> What do you get on the screen?
> copy and paste it to message.
>
>
> On 01/29/2016 09:32 PM, Robert Newberry wrote:
>
> So I looked a DMRGateway.ini under /etc. The ports match what I see in
> DMRGateway.pdf. All of the IPs are 127.0.0.1 which I believe is correct.
>
> I confirmed that AMBEserverGPIO is running.
>
> As far as I know to test this I go to /opt/dmrlink/ambe_audio  then type
> python ambe_audio.py
>
> If Everything is right, I should hear myself in my node. I am connected to
> my node using iaxrpt.
>
> In ambe_audio.cfg what is the remote control port? Default is 1235 the
> gateway port is 1234 which I think is the port between dmrlink and
> dmrgateway.
>
> N1XBM
> Apparare Scientor
> Paratus Communicare
> Allstar Node # 27086, 41540, 41812, 42086, 42658
>
> On Jan 29, 2016 5:43 AM, "Steve Zingman" <szingman at msgstor.com> wrote:
>
>> Is AMBEserverGPIO running? Have you tested it for proper operation?
>> is DMRGateway running? Are the settings in DMRGateway.ini correct?
>>
>>
>>
>>
>> On 01/28/2016 10:16 PM, Robert Newberry wrote:
>>
>> So I followed instructions from previous emails.
>>
>> I first went to my rpt.conf and did this
>>
>> rxchannel = usrp/127.0.0.1:34001:32001
>>
>> Then
>>
>> Configure dmrlink.cfg in /opt/dmrlink/ambe_audio as a master
>>     Configure the repeater to point at the Pi as a peer.
>>         cd /opt/dmrlink/ambe_audio
>>         Test it by running python dmrlink.py in ambe_audio Watch the log
>>     stop dmrlink.py
>>     If you have rebooted DMRGateway should be running.
>>         Check it with ps ax | grep DMRGateway
>>             If not start it with /usr/local/bin/DMRGateway &
>>         Make sure asterisk is running and connect a node to it so you can
>> hear it.
>>     start python ambe_audio.py
>>
>> Everything looks OK on the output, other than not hearing myself. I am
>> also using TS2 TG2 which by the looks of the default ambe_audio.cfg in
>> /opt/dmrlink/ambe_audio has TG2 in the filter.
>>
>> Is there any other ports I need to set? It looks like most things are set
>> default.
>>
>>
>>
>> _______________________________________________
>> Allstar-Digital mailing listAllstar-Digital at lists.keekles.orghttp://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
>>
>>
>> --
>> "Anything is possible if you don't know what you are talking about."
>> 1st Law of Logic
>>
>>
>> _______________________________________________
>> Allstar-Digital mailing list
>> Allstar-Digital at lists.keekles.org
>> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
>>
>>
>
> _______________________________________________
> Allstar-Digital mailing listAllstar-Digital at lists.keekles.orghttp://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
>
>
> --
> "Anything is possible if you don't know what you are talking about."
> 1st Law of Logic
>
>
> _______________________________________________
> Allstar-Digital mailing list
> Allstar-Digital at lists.keekles.org
> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.allstarlink.org/pipermail/allstar-digital/attachments/20160129/13334290/attachment.html>