[Allstar Digital] ambe_audio.py and bridge.py

[Robert Newberry]

I was able to resolve the problem in /opt/dmrlink/ambe_audio/dmrlink.cfg I
had to create a peer pointing back the master I have configured in
/opt/dmrlink/bridge/dmrlink.cfg

I had to put the IP 192.168.X.X in the IP field using 0.0.0.0 or 127.0.0.1
would not allow things to work. Everything seems fine.

I was talking to a ham on analog he said the audio was a little hot. I
noticed in the DMRGateway.ini there is a agc gain adjustment. Is this a OK
adjustment to bring the audio down a bit?

I also noticed that if I key too quickly after someone is done talking on
analog my transmission on DMR will not go out. I found waiting a few
seconds, works fine. Would this have something to do with a hang time
setting?

Other than that I can not find any other issues.

Thanks
Bob/N1XBM

On Sat, Jan 30, 2016 at 3:53 PM, Steve Zingman <szingman at msgstor.com> wrote:

> Use netstat,to troubleshoot
>
>
>
> Sent via smoke signal (AT&T 4G LTE)
>
>
> -------- Original message --------
> From: Robert Newberry <N1XBM at amsat.org>
> Date: 01/30/2016 3:45 PM (GMT-05:00)
> To: Steve Zingman <szingman at msgstor.com>
> Subject: Re: [Allstar Digital] ambe_audio.py and bridge.py
>
> Did you want to see what comes up with I type netstat? While I have
> bridge.py or ambe_audio.py?
>
> On Sat, Jan 30, 2016 at 3:35 PM, Steve Zingman <szingman at msgstor.com>
> wrote:
>
>> netstat
>>
>>
>>
>> Sent via smoke signal (AT&T 4G LTE)
>>
>>
>> -------- Original message --------
>> From: Robert Newberry <N1XBM at amsat.org>
>> Date: 01/30/2016 3:33 PM (GMT-05:00)
>> To: Digital linking using Asterisk and app_rpt <
>> allstar-digital at lists.keekles.org>
>> Subject: Re: [Allstar Digital] ambe_audio.py and bridge.py
>>
>> Well I thought I could instead in /opt/dmrlink/ambe_audio/dmrlink.cfg set
>> it up to peer to my master I established in /opt/dmrlink/bridge/dmrlink.cfg
>>
>> That doesn't work either. I obviously have to do something different.
>>
>> On Sat, Jan 30, 2016 at 1:53 PM, Robert Newberry <N1XBM at amsat.org> wrote:
>>
>>> So I am working on getting everything to run at boot. I've been adding
>>> one process at a time to rc.local. So far so good, when I tried to add
>>> ambe_audio.py I got this error.
>>>
>>> raise error.CannotListenError(self.interface, self.port, le)
>>> twisted.internet.error.CannotListenError: Couldn't listen on
>>> 0.0.0.0:50001: [Errno 98] Address already in use.
>>>
>>> So my repeater is a peer to dmrlink in /opt/dmrlink/bridge/dmrlinkcfg. I
>>> also set the same thing up in /opt/dmrlink/ambe_audio/dmrlink.cfg
>>>
>>> This obviously does not work, so can anyone straighten me out?
>>>
>>
>>
>> _______________________________________________
>> Allstar-Digital mailing list
>> Allstar-Digital at lists.keekles.org
>> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
>>
>>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.allstarlink.org/pipermail/allstar-digital/attachments/20160130/d2ebb908/attachment.html>