[Allstar Digital] ambe_audio.py and bridge.py

[Mike Zingman]

Robert

Congrats on your install. Why don't you write up an email detailing what
you did, what you learned and let others benefit from your experiences.

Mike


On Saturday, January 30, 2016, Robert Newberry <N1XBM at amsat.org> wrote:

> I was able to resolve the problem in /opt/dmrlink/ambe_audio/dmrlink.cfg I
> had to create a peer pointing back the master I have configured in
> /opt/dmrlink/bridge/dmrlink.cfg
>
> I had to put the IP 192.168.X.X in the IP field using 0.0.0.0 or 127.0.0.1
> would not allow things to work. Everything seems fine.
>
> I was talking to a ham on analog he said the audio was a little hot. I
> noticed in the DMRGateway.ini there is a agc gain adjustment. Is this a OK
> adjustment to bring the audio down a bit?
>
> I also noticed that if I key too quickly after someone is done talking on
> analog my transmission on DMR will not go out. I found waiting a few
> seconds, works fine. Would this have something to do with a hang time
> setting?
>
> Other than that I can not find any other issues.
>
> Thanks
> Bob/N1XBM
>
> On Sat, Jan 30, 2016 at 3:53 PM, Steve Zingman <szingman at msgstor.com
> <javascript:_e(%7B%7D,'cvml','szingman at msgstor.com');>> wrote:
>
>> Use netstat,to troubleshoot
>>
>>
>>
>> Sent via smoke signal (AT&T 4G LTE)
>>
>>
>> -------- Original message --------
>> From: Robert Newberry <N1XBM at amsat.org
>> <javascript:_e(%7B%7D,'cvml','N1XBM at amsat.org');>>
>> Date: 01/30/2016 3:45 PM (GMT-05:00)
>> To: Steve Zingman <szingman at msgstor.com
>> <javascript:_e(%7B%7D,'cvml','szingman at msgstor.com');>>
>> Subject: Re: [Allstar Digital] ambe_audio.py and bridge.py
>>
>> Did you want to see what comes up with I type netstat? While I have
>> bridge.py or ambe_audio.py?
>>
>> On Sat, Jan 30, 2016 at 3:35 PM, Steve Zingman <szingman at msgstor.com
>> <javascript:_e(%7B%7D,'cvml','szingman at msgstor.com');>> wrote:
>>
>>> netstat
>>>
>>>
>>>
>>> Sent via smoke signal (AT&T 4G LTE)
>>>
>>>
>>> -------- Original message --------
>>> From: Robert Newberry <N1XBM at amsat.org
>>> <javascript:_e(%7B%7D,'cvml','N1XBM at amsat.org');>>
>>> Date: 01/30/2016 3:33 PM (GMT-05:00)
>>> To: Digital linking using Asterisk and app_rpt <
>>> allstar-digital at lists.keekles.org
>>> <javascript:_e(%7B%7D,'cvml','allstar-digital at lists.keekles.org');>>
>>> Subject: Re: [Allstar Digital] ambe_audio.py and bridge.py
>>>
>>> Well I thought I could instead in /opt/dmrlink/ambe_audio/dmrlink.cfg
>>> set it up to peer to my master I established in
>>> /opt/dmrlink/bridge/dmrlink.cfg
>>>
>>> That doesn't work either. I obviously have to do something different.
>>>
>>> On Sat, Jan 30, 2016 at 1:53 PM, Robert Newberry <N1XBM at amsat.org
>>> <javascript:_e(%7B%7D,'cvml','N1XBM at amsat.org');>> wrote:
>>>
>>>> So I am working on getting everything to run at boot. I've been adding
>>>> one process at a time to rc.local. So far so good, when I tried to add
>>>> ambe_audio.py I got this error.
>>>>
>>>> raise error.CannotListenError(self.interface, self.port, le)
>>>> twisted.internet.error.CannotListenError: Couldn't listen on
>>>> 0.0.0.0:50001: [Errno 98] Address already in use.
>>>>
>>>> So my repeater is a peer to dmrlink in /opt/dmrlink/bridge/dmrlinkcfg.
>>>> I also set the same thing up in /opt/dmrlink/ambe_audio/dmrlink.cfg
>>>>
>>>> This obviously does not work, so can anyone straighten me out?
>>>>
>>>
>>>
>>> _______________________________________________
>>> Allstar-Digital mailing list
>>> Allstar-Digital at lists.keekles.org
>>> <javascript:_e(%7B%7D,'cvml','Allstar-Digital at lists.keekles.org');>
>>> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
>>>
>>>
>>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.allstarlink.org/pipermail/allstar-digital/attachments/20160130/d74ff947/attachment.html>