[App_rpt] Getting app_rpt base node to work.

[Shane Burrell]

Still get rpt_exec: Cannot find specified system node 101.  my rpt.conf is
as follows:

[101]					; Node ID of remote base
rxchannel = Zap/25			; Rx audio/signalling channel
txchannel = Zap/26			; Tx audio/signalling channel
functions = functions-remote
remote = dumb				; Set remote=y for dumb remote or 
					; remote=rbi for Doug Hall RBI1
[functions-remote]
0=remote,1				; Retrieve Memory
1=remote,2				; Set freq.
2=remote,3				; Set Rx PL tone.
40=remote,100				; Rx PL off
41=remote,101				; Rx PL on
42=remote,102				; Tx PL off
43=remote,103				; Tx PL on
44=remote,104				; Low Pwr
45=remote,105				; Med Pwr
46=remote,106				; Hi Pwr
5=remote,5				; Status

[telemetry]


ct1=|t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048)
ct2=|t(660,880,150,2048)  
ct3=|t(440,0,150,2048) 
ct4=|t(550,0,150,2048)
ct5=|t(660,0,150,2048)
ct6=|t(880,0,150,2048)
ct7=|t(660,440,150,2048)
ct8=|t(700,1100,150,2048)
remotetx=|t(2000,0,75,2048)(0,0,75,0)(1600,0,75,2048); 
remotemon=|t(1600,0,75,2048) 
cmdmode=|t(900,903,200,2048)
functcomplete=|t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)

[morse]
speed=20		; Approximate speed in WPM
frequency=800		; Morse Telemetry Frequency
amplitude=4096		; Morse Telemetry Amplitude
idfrequency=330		; Morse ID Frequency	
idamplitude=2048	; Morse ID Amplitude

[nodes]

;000 = context_A at 1.2.3.4/1234
101 = radio at me.asterisk.net/101

;of course, you can also specify these with domain names, but why rely
;on DNS working unnecessarily?

[memory]

;; this example gives you 146.460, simplex, 100.0 HZ PL, hi-power, transmit
PL
00 = 146.460,100.0,sht
;; this example gives you 146.940, minus offset, 100.0 HZ PL, low-power, no
PL
01 = 146.940,100.0,-l

; The format for these entries is:  Receive-Freq,Receive-PL,Attrbutes
;     Attributes: l=low power, m=medium power, h=high power, -=minus offset,
;	s=simplex, +=plus offset, t=tx PL enable, r=rx PL enable


-----Original Message-----
From: app_rpt-bounces at lists.illiana.net
[mailto:app_rpt-bounces at lists.illiana.net] On Behalf Of
hwstar at rodgers.sdcoxmail.com
Sent: Friday, July 21, 2006 1:10 PM
To: Asterisk Repeater Controler
Subject: Re: [App_rpt] Getting app_rpt base node to work.

Shane,


1. Node numbers with leading zeroes are reserved. Try using 101 instead.

2. The node number needs to be defined in 2 places in the rpt.conf file.
Once in the repeater section with square brackets e.g. [101] and once in the
[NODES] section as an entry to connect to/from:

radio at 127.0.0.1/101,127.0.0.1


Steve.

> 
> From: "Shane Burrell" <shaneb at metrostat.net>
> Date: 2006/07/21 Fri AM 10:04:30 PDT
> To: <app_rpt at lists.illiana.net>
> Subject: [App_rpt] Getting app_rpt base node to work.
> 
> I've tried to setup a base node using a kenwood TK-880 and analog radio
> board.  Asterisk reports that rpt_exec: Cannot find specified system node
> 001.  I have 001 defined using the example base node.  Is there something
I
> am missing.  Does app-rpt require more than a reload to get its
> configuration?
> 
>  
> 
> Regards,
> 
>  
> 
>  
> 
> Shane 
> 
>  
> 
> 
>