[App_rpt-users] CTCSS Drop Out Time

[Ron Morell]

In the how to recompile, reinstall, and restart, I do not see 'make clean'.
So in the source root directory:
make clean
make
make install
astres.sh

This should solve the target not found error message.
73 and Merry Christmas,
Ron - KA7U

Did you recompile, reinstall, and restart asterisk?

 

From: app_rpt-users-bounces at ohnosec.org <http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users>
[mailto:app_rpt-users-bounces at ohnosec.org <http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users>] On Behalf Of Jim W7RY
Sent: Saturday, December 24, 2011 11:34 PM
To: Ken; 'Jim Duuuude'; 'app_rpt mailing list'
Subject: Re: [App_rpt-users] CTCSS Drop Out Time

 

It seems to be here:  /usr/src/astsrc/asterisk/channels/xpmr

 

And the line is: #define TOC_NOTONE_TIME             900                //
ms

 

I changed it from 600 to 900. 

 

Did not change a thing... Did I change the right thing?

 

 

 

From: Ken <mailto:ke2n at cs.com <http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users>>  

Sent: Saturday, December 24, 2011 6:01 PM

To: 'Jim Duuuude' <mailto:telesistant at hotmail.com <http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users>>  ; w7ry at centurytel.net <http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users> ;
'app_rpt mailing list' <mailto:app_rpt-users at ohnosec.org <http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users>>  

Subject: RE: [App_rpt-users] CTCSS Drop Out Time

 

Notone AKA chicken burst gives you carrier with no tone at the end.

But some radios are too slow in closing the CTCSS and still make noise.

There was a posting on here a while back that pointed the time delay in: 

 

/usr/src/asterisk/asterisk/channels/xpmr/xpmr.h

 

The default is 600 ms.  Some radios might be slower than this.

You could change (increase) it, then  make / make install and restart
asterisk.

 

My Alinco DR-?35 series seem to want to give you a small squelch tail no
matter what you do, however.

 

73

 

Ken

 
Reading along this thread, I notice 'make clean' is not in the 'how to'.  So try it like this:

 

From: app_rpt-users-bounces at ohnosec.org <http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users>
[mailto:app_rpt-users-bounces at ohnosec.org <http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users>] On Behalf Of Jim Duuuude
Sent: Saturday, December 24, 2011 6:17 PM
To: w7ry at centurytel.net <http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users>; app_rpt mailing list
Subject: Re: [App_rpt-users] CTCSS Drop Out Time

 

try

txtoctype = notone

in usbradio.conf

JIM WB6NIL

  _____  

From: w7ry at centurytel.net <http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users>
To: app_rpt-users at ohnosec.org <http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users>
Date: Sat, 24 Dec 2011 13:55:51 -0800
Subject: [App_rpt-users] CTCSS Drop Out Time

Anyone know if there is an adjustment of the time the transmitter stays
keyed, and the PL tone drops out and where that setting is?

With my rigs, I still here the squelch crash after the repeater drops out. I
would like to cut the PL off a little sooner or delay the transmitter a
little longer.

 

BTW, I'm all up and running with the repeater function and the node!  Thanks
to all that helped me get past the learning curve!

 

Thanks!

Merry Christmas

73 Jim W7RY