[App_rpt-users] My first post and a real newbie question

[Jim Duuuude]

also for transmit, set txprelim=no. That will make it not generate
"flat" pre-emphasized limited audio for direct modulation.

JIM

From: telesistant at hotmail.com
To: jrorke at cogeco.ca; app_rpt-users at ohnosec.org
Date: Mon, 4 Jul 2011 05:18:21 -0700
Subject: Re: [App_rpt-users] My first post and a real newbie question








duplex=1 is quite nice, actually.

What you really need to do is set carrierfrom=usbinvert
since your signal is *low* true.

JIM WB6NIL

> Date: Mon, 4 Jul 2011 08:15:44 -0400
> From: jrorke at cogeco.ca
> To: app_rpt-users at ohnosec.org
> Subject: Re: [App_rpt-users] My first post and a real newbie question
> 
> Hi Michel, Ok set duplex = 0 in the Rpt.conf
> And set your hangtime = 1 (change it from 1000).
> 
> That should get you simplex node working.
> 
> Also there will be no telemetry but you will hear connect /disconnect 
> messages.
> 
> If there is no statement in Rpt.conf for duplex, it operates in full 
> duplex by default.
> 
> Hope this helps.
> 
> Jon VA3RQ
> 
> On 7/4/2011 6:16 AM, Michael Carey wrote:
> > Hi Everybody,
> >
> > I'm busy finalising my AllStarLink node 27871 . It's going to be a 
> > simplex (for now) node with the future potential to be linked to my 
> > local 70cm repeater.
> >
> > I am finding one little problem that I can't seem to solve. I have set 
> > duplex in usbradio.conf to zero (0) and duplex in rpt.conf to one (1), 
> > but as soon as my node radio receives a transmission, it keys up 
> > straight away... over the incoming transmission, almost as if it is 
> > still configured for duplex mode. This makes it real hard to enter any 
> > DTMF codes. (-: Where should be I looking to solve this?
> >
> > I am handling CTCSS (both TX and RX) in the node radio itself (I am 
> > using a Simoco SRM9000 VHF commercial radio). I have a low going logic 
> > level that has been tied to the radios "valid signal" flag which is 
> > set to CTCSS 107.2Hz, this is fed to the COS input on my URI. The 
> > audio output from the radio is squelched, highpass filtered and 
> > de-emphasised.
> >
> > I have set carrierfrom=usb and ctcssfrom=no, I think this then 
> > disables CTCSS decoding within the computer.  Does this also disable 
> > transmitting CTCSS? I have set txmixa=voice which I presume also stops 
> > CTCSS from being output from the URI.
> >
> > I look forward to hearing from you all... via the email list and on 
> > air too!
> >
> > Michael
> > VK5ZEA
> >
> >
> >
> >
> >
> >
> >
> >
> >
> > _______________________________________________
> > App_rpt-users mailing list
> > App_rpt-users at ohnosec.org
> > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
> >
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at ohnosec.org
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
 		 	   		  

_______________________________________________
App_rpt-users mailing list
App_rpt-users at ohnosec.org
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users 		 	   		  
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.keekles.org/pipermail/app_rpt-users/attachments/20110704/85032304/attachment.html>