[App_rpt-users] cor active PL logic

[Monty]

I believe it is for the generated tone from app_rpt.  I have not used a
Beagleboard as of yet, maybe someone who has could let us know.  I would
imagine instead of cop 58 and 59 you would use 61 to manipulate, see
http://ohnosec.org/drupal/node/177.  Try this:

[functions]
900 = cop,61,GPIO1=1        ;Tx CTCSS On Input only Enable (High)
901 = cop,61,GPIO1=0        ;Tx CTCSS On Input only Disable (Low)


Monty


On Sun, Jan 1, 2012 at 9:22 PM, Fredric Moses <fred at moses.bz> wrote:

> Thanks for the reply monty..  But when I enable this is it controlling a
> logic gpio. or is it controlling the PL freq generated into the audio audio
> out...  I am using the beagleboard/lox combo which i was under the
> impression needed external decode and encode of pl's.. Unlike the usb
> interface from dmkeng...
>
>  --
> Fredric Moses - W8FSM - WQOG498
> fred at moses.bz
>
>
>
>
> On Jan 1, 2012, at 11:19 PM, Monty wrote:
>
> Hi Fredric,
> That command list was pulled from the source app_rpt.c and the asterisks
> are to comment those lines out.  To excute those commands you will need to
> create a function.  I put them under [functions] in
> /etc/asterisk/rpt.conf.  For example:
>
> [functions]
> 900 = cop,58        ;Tx CTCSS On Input only Enable
> 901 = cop,59        ;Tx CTCSS On Input only Disable
>
> A *900 will execute TX CTCSS Enable, *901 will execute TX CTCSS Disable.
>
> Also Allstarnode.com is not maintained by the developers of app_rpt, it
> is a third party site.  The current site for configuration information is
> http://ohnosec.org/drupal.  The variable you are looking for is
> documented at http://ohnosec.org/drupal/node/176.
>
>
> Monty
>
>
> On Sun, Jan 1, 2012 at 2:04 AM, Fredric Moses <fred at moses.bz> wrote:
>
>> I am working on getting a logic output to run my PL encoder for COR
>> active PL on the main repeater port.  using a variable i was able to get it
>> to work fine with local RX audio. When a signal is present I have a gpio
>> pin going low.. when not present going back high..   but can not find a
>> variable to watch for IP links coming in. Is there one?  Is there something
>> I can watch so that I can make the logic pin swing..?
>>
>> Some google foo found these commands
>> * 56 - Rx CTCSS Enable
>> * 57 - Rx CTCSS Disable
>> * 58 - Tx CTCSS On Input only Enable
>> * 59 - Tx CTCSS On Input only Disable
>> http://allstarnode.com/viewtopic.php?f=5&t=8
>>
>> The only mention I see of TX PL is with use of a USB radio interface.
>>  Will *58 follow the tx pl settings set in usbradio if I had a USB radio
>> device vs using one of the LOX ports for the main repeater..
>>
>> --
>> Fredric Moses - W8FSM - WQOG498
>> fred at moses.bz
>>
>>
>>
>>
>> _______________________________________________
>> App_rpt-users mailing list
>> App_rpt-users at ohnosec.org
>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>>
>
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.keekles.org/pipermail/app_rpt-users/attachments/20120101/d7e22212/attachment.html>