[App_rpt-users] Alternate IAX port >> bind port not working
Bryan D. Boyle
bdboyle at bdboyle.com
Fri Oct 12 13:59:49 UTC 2012
have you changed the port you use AT the portal? ie the server configuration, network configuration tab?
if you have a node that needs to be on a different port, the underlying server needs to be moved both at the end, as well as at the mother ship.
had the same problem until i had everything lined up.
--
Bryan
Sent from my iPhone 5
please forgive misspellings...
On Oct 12, 2012, at 8:07, Jon Rorke <jrorke at cogeco.ca> wrote:
> I check the node I am working on and it has the following:
>
>> ; Inter-Asterisk eXchange driver definition
>> ;
>> ;
>>
>> [general]
>> bindport=4570
>> bindaddr=0.0.0.0
>> disallow=all
>> allow=gsm
>> allow=g726aal2
>> allow=ulaw
>> jitterbuffer=yes
>> forcejitterbuffer=yes
>> dropcount=2
>> maxjitterbuffer=4000
>> maxjitterinterps=10
>> resyncthreshold=1000
>> maxexcessbuffer=80
>> minexcessbuffer=10
>> jittershrinkrate=1
>> tos=0x1E
>> autokill=yes
>> delayreject=yes
>> ;iaxthreadcount=30
>> ;iaxmaxthreadcount=150
>
> So bindport is set correctly but the node is still reporting to all the others as port 4569. in the RPT_extnodes list.
>
> 28505=radio at 66.206.229.10:4569/28505,66.206.229.10
> I have port 4570 open in the router but the node is not reachable because of this.
>
>
> On 10/12/2012 12:12 AM, Kevin Oleniczak wrote:
>> I finally got this working. To close this out, here's what i found.
>>
>> It turns out the issue was that i had binaddr listed above bindport in iax.conf. In order for bindport to get used, it has to appear in the file before bindaddr.
>>
>> thanks to all who helped with this.
>>
>> On Tue, Oct 9, 2012 at 8:40 PM, Tim Sawyer <tim.sawyer at mac.com> wrote:
>>> Try changing your IP address setting on the Portal to either DHCP or Fixed. I don't know what the VoIP setting you currently have it set for does.
>>> --
>>> Tim
>>> :wq
>>>
>>> On Oct 9, 2012, at 5:29 PM, Kevin Oleniczak <kevinoleniczak at gmail.com> wrote:
>>>
>>>> I had already done that in the portal but it still wasn't working. As an experiment, i changed everything back to the original 4569 port and forwarded that on my router. I could then connect with the webtransceiver. However i can't leave it there and need to get it to work on an alternate port. It seems from my testing that something is hard set to port 4569 on the allstar end of things?
>>>>
>>>> ideas?
>>>>
>>>> thank you
>>>>
>>>> On Tue, Oct 9, 2012 at 3:47 AM, Ken <ke2n at cs.com> wrote:
>>>>> Yes – you need to log onto the portal and get to the server configuration tab – there is a place there to change to port number that the registration server is talking to.
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>> Ken
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>> From: app_rpt-users-bounces at ohnosec.org [mailto:app_rpt-users-bounces at ohnosec.org] On Behalf Of Kevin Oleniczak
>>>>> Sent: Tuesday, October 09, 2012 12:09 AM
>>>>> To: app_rpt-users at ohnosec.org
>>>>> Subject: [App_rpt-users] Alternate IAX port >> Registered ok but not listed?
>>>>>
>>>>>
>>>>>
>>>>> I am unable to connect to my node from the webtransceiver and don't see it listed on the active nodes page. I use an alternate iax port because i have to.
>>>>>
>>>>> From reading other posts… it seems I may need an admin to change my iax port from 4569 to what I now want to use which is 4570? thoughts?
>>>>>
>>>>>
>>>>>
>>>>> My registration is still showing 4569 and am forwarding 4570 on my router to my ACID box.
>>>>>
>>>>>
>>>>>
>>>>> cruiser*CLI> iax2 show registry
>>>>>
>>>>> Host dnsmgr Username Perceived Refresh State
>>>>>
>>>>> <myip>:4569 N 28970 <myip>:4569 60 Registered
>>>>>
>>>>>
>>>>>
>>>>> I’m not seeing my node show up and believe this is the cause. In my iax.conf I have bindport set 4570 and also in server config under network I set port 4570 on the portal.
>>>>>
>>>>>
>>>>>
>>>>> looking at rpt_extnodes i see my node listed with the correct port...
>>>>>
>>>>>
>>>>>
>>>>> 28970=radio@<myip>:4570/28970,<myip>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>> [general]
>>>>>
>>>>> bindaddr=0.0.0.0
>>>>>
>>>>> bindport=4570
>>>>>
>>>>> ....
>>>>>
>>>>>
>>>>>
>>>>> register=28970:<mypasswd>@register.allstarlink.org
>>>>>
>>>>
>>>> _______________________________________________
>>>> App_rpt-users mailing list
>>>> App_rpt-users at ohnosec.org
>>>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>>
>>
>>
>> _______________________________________________
>> App_rpt-users mailing list
>> App_rpt-users at ohnosec.org
>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at ohnosec.org
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.keekles.org/pipermail/app_rpt-users/attachments/20121012/e5a766e9/attachment.html>
More information about the App_rpt-users
mailing list