[App_rpt-users] Alternate IAX port >> bind port not working

[Steve Passmore]

comment out or remove
bindaddr=0.0.0.0


On 10/12/2012 5:07, Jon Rorke wrote:
> I check the node I am working on and it has the following:
>
>> ; Inter-Asterisk eXchange driver definition
>> ;
>> ;
>>
>> [general]
>> bindport=4570
>> bindaddr=0.0.0.0
>> disallow=all
>> allow=gsm
>> allow=g726aal2
>> allow=ulaw
>> jitterbuffer=yes
>> forcejitterbuffer=yes
>> dropcount=2
>> maxjitterbuffer=4000
>> maxjitterinterps=10
>> resyncthreshold=1000
>> maxexcessbuffer=80
>> minexcessbuffer=10
>> jittershrinkrate=1
>> tos=0x1E
>> autokill=yes
>> delayreject=yes
>> ;iaxthreadcount=30
>> ;iaxmaxthreadcount=150
>
> So bindport is set correctly but the node is still reporting to all 
> the others as port 4569. in the RPT_extnodes list.
>
> 28505=radio at 66.206.229.10:4569/28505,66.206.229.10
> I have port 4570 open in the router but the node is not reachable 
> because of this.
>
>
> On 10/12/2012 12:12 AM, Kevin Oleniczak wrote:
>> I finally got this working. To close this out, here's what i found.
>>
>> It turns out the issue was that i had binaddr listed above bindport 
>> in iax.conf. In order for bindport to get used, it has to appear in 
>> the file before bindaddr.
>>
>> thanks to all who helped with this.
>>
>> On Tue, Oct 9, 2012 at 8:40 PM, Tim Sawyer <tim.sawyer at mac.com 
>> <mailto:tim.sawyer at mac.com>> wrote:
>>
>>     Try changing your IP address setting on the Portal to either DHCP
>>     or Fixed. I don't know what the VoIP setting you currently have
>>     it set for does.
>>     --
>>     Tim
>>     :wq
>>
>>     On Oct 9, 2012, at 5:29 PM, Kevin Oleniczak
>>     <kevinoleniczak at gmail.com <mailto:kevinoleniczak at gmail.com>> wrote:
>>
>>>     I had already done that in the portal but it still wasn't
>>>     working. As an experiment, i changed everything back to the
>>>     original 4569 port and forwarded that on my router. I could then
>>>     connect with the webtransceiver. However i can't leave it there
>>>     and need to get it to work on an alternate port. It seems from
>>>     my testing that something is hard set to port 4569 on the
>>>     allstar end of things?
>>>
>>>     ideas?
>>>
>>>     thank you
>>>
>>>     On Tue, Oct 9, 2012 at 3:47 AM, Ken <ke2n at cs.com
>>>     <mailto:ke2n at cs.com>> wrote:
>>>
>>>         Yes -- you need to log onto the portal and get to the server
>>>         configuration tab -- there is a place there to change to
>>>         port number that the registration server is talking to.
>>>
>>>         Ken
>>>
>>>         *From:*app_rpt-users-bounces at ohnosec.org
>>>         <mailto:app_rpt-users-bounces at ohnosec.org>
>>>         [mailto:app_rpt-users-bounces at ohnosec.org
>>>         <mailto:app_rpt-users-bounces at ohnosec.org>] *On Behalf Of
>>>         *Kevin Oleniczak
>>>         *Sent:* Tuesday, October 09, 2012 12:09 AM
>>>         *To:* app_rpt-users at ohnosec.org
>>>         <mailto:app_rpt-users at ohnosec.org>
>>>         *Subject:* [App_rpt-users] Alternate IAX port >> Registered
>>>         ok but not listed?
>>>
>>>         I am unable to connect to my node from the webtransceiver
>>>         and don't see it listed on the active nodes page. I use an
>>>         alternate iax port because i have to.
>>>
>>>         From reading other posts... it seems I may need an admin to
>>>         change my iax port from 4569 to what I now want to use which
>>>         is 4570? thoughts?
>>>
>>>         My registration is still showing 4569 and am forwarding 4570
>>>         on my router to my ACID box.
>>>
>>>         cruiser*CLI> iax2 show registry
>>>
>>>         Host dnsmgr  Username Perceived             Refresh State
>>>
>>>         <myip>:4569 N       28970 <myip>:4569          60 Registered
>>>
>>>         I'm not seeing my node show up and believe this is the
>>>         cause. In my iax.conf I have bindport set 4570 and also in
>>>         server config under network I set port 4570 on the portal.
>>>
>>>         looking at rpt_extnodes i see my node listed with the
>>>         correct port...
>>>
>>>         28970=radio@<myip>:4570/28970,<myip>
>>>
>>>         [general]
>>>
>>>         bindaddr=0.0.0.0
>>>
>>>         bindport=4570
>>>
>>>         ....
>>>
>>>         register=28970:<mypasswd>@register.allstarlink.org
>>>         <http://register.allstarlink.org/>
>>>
>>>
>>>     _______________________________________________
>>>     App_rpt-users mailing list
>>>     App_rpt-users at ohnosec.org <mailto:App_rpt-users at ohnosec.org>
>>>     http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>>
>>
>>
>>
>> _______________________________________________
>> App_rpt-users mailing list
>> App_rpt-users at ohnosec.org
>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>
>
>
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at ohnosec.org
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.keekles.org/pipermail/app_rpt-users/attachments/20121012/d99cd54b/attachment.html>