[App_rpt-users] Frequency Agile Remote - XCAT FUBAR

[Robert A. Poff WB3AWJ]

Still digging on my Agile Remote. 

Acid with a Syntor X and XCAT. 
When I try to set a frequency, it's sending the CIV string to retrieve a memory from the radio. 
Not the string needed to set it from one of the memory entries in rpt.conf. 

Running Asterisk in the foreground with all the debug turned up here's what I see on the console executing a *017 command : 

@@@@ action: remote, param = 1 
@@@@ table index i = 5 
[Aug 1 15:06:09] NOTICE[2718]: app_rpt.c:17558 function_remote: 28260 param=1 digitbuf=17 source=2 
[Aug 1 15:06:09] NOTICE[2718]: app_rpt.c:17483 get_mem_set: digitbuf=17 
[Aug 1 15:06:09] NOTICE[2718]: app_rpt.c:4225 retrieve_memory: memory=17 block=memory 
[Aug 1 15:06:09] NOTICE[2718]: app_rpt.c:10476 rpt_telemetry: Tracepoint rpt_telemetry() entered mode=38 
[Aug 1 15:06:09] NOTICE[2718]: app_rpt.c:10760 rpt_telemetry: Tracepoint rpt_telemetry() exit 
[Aug 1 15:06:09] NOTICE[2718]: app_rpt.c:17486 get_mem_set: freq=146.520 res=0 
[Aug 1 15:06:09] NOTICE[2718]: app_rpt.c:12849 collect_function_digits: rv=3 
[Aug 1 15:06:09] NOTICE[2718]: app_rpt.c:10476 rpt_telemetry: Tracepoint rpt_telemetry() entered mode=3 
[Aug 1 15:06:09] NOTICE[2718]: app_rpt.c:10760 rpt_telemetry: Tracepoint rpt_telemetry() exit 
Mode 
[Aug 1 15:06:09] NOTICE[2731]: app_rpt.c:13870 serial_remote_io: ioport=/dev/ttyS0 baud=14 iofd=0x19 
String output was �� 
�'Ms: 
FE FE 20 E0 08 01 FD 
[Aug 1 15:06:09] NOTICE[2732]: app_rpt.c:8420 wait_interval: Delay interval = 2000 
[Aug 1 15:06:10] WARNING[2731]: app_rpt.c:13910 serial_remote_io: -99999 Serial device not responding on node 28260 
Offset Initial/Simplex 
Frequency 
Offset 
CTCSS 
Frequency 
[Aug 1 15:06:10] NOTICE[2731]: app_rpt.c:8420 wait_interval: Delay interval = 2000 
[Aug 1 15:06:11] NOTICE[2732]: app_rpt.c:8424 wait_interval: Delay complete 
-- Hungup 'Zap/pseudo-1521668112' 
[Aug 1 15:06:12] NOTICE[2731]: app_rpt.c:8424 wait_interval: Delay complete 
-- <Zap/pseudo-1162233705> Playing 'rpt/invalid-freq' (language 'en') 

At one point I added a statement to printf myrpt->remoterig variable in the check_freq function. 
It returned "myrpt->remoterig=Mode" ????? 
Shouldn't that be "xcat", or "remote_rig_xcat" ? 

Any suggestions where I should be looking? 







Robert A. Poff 
Loganville, PA. 


"Lieutenant, target the offending power boat and launch photon torpedoes" 
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.keekles.org/pipermail/app_rpt-users/attachments/20130801/f9818b04/attachment.html>