[App_rpt-users] No TX audio upon reboot after initial install. Slow DMK URI LED Blink (Detailed info)
Jon Rorke
jrorke at cogeco.ca
Thu Nov 14 12:51:17 UTC 2013
Well it seems your box may not have the hoarse power to do dsp on
App_Rpt. Perhaps if you switch from Chan_ USB radio to Chan_simple USB
and use the Radios' Cor and tone decoder then it would off load a lot of
processing power.
RQ
On 11/13/2013 11:44 PM, Johnny Keeker wrote:
> Im not sure exactly what your explaining so if you havent already
> done so, try changingctcssfrom=dsp to ctcssfrom=no.
> I thought the blinking light on the URI was the PC heartbeat.
> Check the CLI screen when its slow to make sure asterisk starts correctly.
> Also check the sound driver. As root type this command to see if your
> URI is recognized;
> [root at yournode~] /dmesg/
> somewhere on the screen you should see something like this;
> usb 3-2: configuration #1 chosen from 1 choice
> input: C-Media Electronics Inc.USB PnP Sound Device as /class/input/input1
> JK
>
>
> *From:* William Schleppegrell <wschleppegrell at gmail.com>
> *To:* app_rpt-users <app_rpt-users at ohnosec.org>
> *Sent:* Wednesday, November 13, 2013 6:39 PM
> *Subject:* [App_rpt-users] No TX audio upon reboot after initial
> install. Slow DMK URI LED Blink (Detailed info)
>
> My node consists of an Intel NUC DCCP847DYE PC Which has an Intel
> Celeron^(TM) Processor 847(1.10 GHz, 2M Cache)
> It has 3 USB ports and Video / Audio out are supported by 2 HDMI ports
> which may be part of my problem.
> .
> Intel® HD Graphics
> .
> Dual HDMI Ports supporting dual independent display
>
> Intel® High Definition Audio (Intel® HD Audio) via two
> HDMI 1.4a outputs supporting 8 channel (7.1) digital
> audio
>
> I am running a single node on this pc. The node is operating a UHF
> repeater. Two radios. Icom Commercial IC-F420 mobiles via a DMK URI.
>
> I loaded ACID and my system ran fine until I rebooted. This is my
> second attempt at installation.
>
> I will include my .conf files below. I have PL tones set on radios
> but am not using COR/COS. I utilize the software to detect PL to
> trigger TX/RX.
>
> I have a slow blinking green LED on the DMK URI 2-3 flashes per
> second, when it has failed and is not sending audio to the TX
> radio(like now). And a nice fast blink pattern when it is working.
>
> Ok...Oh the is keying up with a staticy transmission during ID's and
> when Flash is run in the radio-tune-menu, but not recognizable audio
> is heard.
>
> RPT.CONF
>
> [29922] ; Change this to your assigned
> node number
>
> rxchannel=Radio/usb29922
> duplex=2
> erxgain=-3
> etxgain=3
> ;controlstates=controlstates
> scheduler=schedule29922
> morse=morse29922
> macro=macro29922
> functions=functions29922
> phone_functions=functions29922
> link_functions=functions29922
> telemetry=telemetry
> wait_times=wait-times
> context = radio
> callerid = "Repeater" <0000000000>
> idrecording = |iAE5YY
> accountcode=RADIO
> hangtime=100
> althangtime=100
> totime=170000
> idtime=540000
> politeid=3000
>
> idtalkover=|iAE5YY
> unlinkedct=ct2
> remotect=ct3
> linkunkeyct=ct8
> ;nolocallinkct=0
> ;eannmode=1
> ;connpgm=yourconnectprogram
> ;discpgm=yourdisconnectprogram
> ;lnkactenable=0
> ;lnkacttime=1800
> ;lnkactmacro=*52
> ;lnkacttimerwarn=30seconds
> ;remote_inact_timeout=1800
> ;remote_timeout=3600
> nounkeyct=0
> ;holdofftelem=0
> beaconing=0
> ;
> ; *** Status Reporting ***
> ;
> ; Uncomment the either group following two statpost lines to report
> the status of your node to stats.allstarlink.org
> <http://stats.allstarlink.org/>
> ; depending on whether you are running ACID or Limey Linux.
>
> ; ** For ACID ***
> statpost_program=/usr/bin/wget,-q,--timeout=15,--tries=1,--output-document=/dev/null
> statpost_url=http://stats.allstarlink.org/uhandler.php ; Status updates
>
> ; ** For Limey Linux **
> ;statpost_program=/bin/wget,-q,--timeout=15,--tries=1,--output-document=/dev/null
> ;statpost_url=http://stats.allstarlink.org/uhandler.php ; Status updates
>
> ;
> ; Morse code parameters, these are common to all repeaters.
> ;
>
> [morse29922]
>
> speed=18
> frequency=800
> amplitude=4096
> idfrequency=750
> idamplitude=1024
>
> [schedule29922]
> ;dtmf_function = m h dom mon dow ; ala cron, star is implied
>
> [functions29922]
> 1=ilink,1
> 2=ilink,2
> 3=ilink,3
> 4=ilink,4
> 5=macro,1
> 70=ilink,5
> 71=ilink,6
> 72=ilink,7
> 73=ilink,15
> 74=ilink,16
> 75=ilink,8
>
> 80=status,1
> 81=status,2
>
> 6=autopatchup,noct=1,farenddisconnect=1,dialtime=20000 ; Autopatch up
> 0=autopatchdn ; Autopatch down
>
> ;989=cop,4
> 980=status,3
> 99=cop,6
>
> ; Place command macros here
>
> [macro29922]
>
>
>
> [telemetry]
>
> ct1=|t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048)
> ct2=|t(660,880,150,2048)
> ct3=|t(440,0,150,4096)
> ct4=|t(550,0,150,2048)
> ct5=|t(660,0,150,2048)
> ct6=|t(880,0,150,2048)
> ct7=|t(660,440,150,2048)
> ct8=|t(700,1100,150,2048)
> remotetx=|t(1633,0,50,3000)(0,0,80,0)(1209,0,50,3000);
> remotemon=|t(1209,0,50,2048)
> cmdmode=|t(900,903,200,2048)
> functcomplete=|t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)
> patchup=rpt/callproceeding
> [wait-times]
> telemwait=2000
> idwait=500
> unkeywait=2000
> calltermwait=2000
>
> ;
> ; This is where you define your nodes which cam be connected to.
> ;
>
> [nodes]
> ; Note, if you are using automatic update for allstar link nodes,
> ; no allstar link nodes should be defined here. Only place a definition
> ; for your locak nodes, and private (off of allstar link) nodes here.
>
> 29922 = radio at 127.0.0.1/29922,NONE
>
> ; Memories for remote bases
>
> [memory]
>
> ;00 = 146.580,100.0,m
> ;01 = 147.030,103.5,m+t
> ;02 = 147.240,103.5,m+t
> ;03 = 147.765,79.7,m-t
> ;04 = 146.460,100.0,m
> ;05 = 146.550,100.0,m
>
>
> USBRADIO.CONF
> [general]
>
> [usb29922]
>
> hdwtype=0
> rxboost=1
> txboost=1
> rxctcssrelax=1
> txctcssdefault=136.5
> rxctcssfreqs=136.5
> txctcssfreqs=136.5
> ;rxctcssoverride=0
> carrierfrom=dsp
> ctcssfrom=dsp
> rxdemod=flat
> txprelim=no
> txlimonly=no
> txtoctype=no
> txmixa=composite
> txmixb=no
> invertptt=0
> duplex=1
> rxondelay=0
> rxnoisefiltype=0
> eeprom=0
>
> #includeifexists custom/usbradio.conf
>
> IAX.CONF
> ; Inter-Asterisk eXchange driver definition
> ;
> ;
>
> [general]
> bindport=4569
> bindaddr=0.0.0.0
> disallow=all
> allow=gsm
> allow=g726aal2
> allow=ulaw
> jitterbuffer=yes
> forcejitterbuffer=yes
> dropcount=2
> maxjitterbuffer=4000
> maxjitterinterps=10
> resyncthreshold=1000
> maxexcessbuffer=80
> minexcessbuffer=10
> jittershrinkrate=1
> tos=0x1E
> autokill=yes
> delayreject=yes
> ;iaxthreadcount=30
> ;iaxmaxthreadcount=150
>
> register=29922:<PASSWORD OMITTED>@register.allstarlink.org
> <http://register.allstarlink.org/>
> IN EMAIL for SECURITY
> [radio-proxy]
> type=user
> deny=0.0.0.0/0.0.0.0 <http://0.0.0.0/0.0.0.0>
> permit=/255.255.255.255 <http://255.255.255.255/>
> context=radio-secure-proxy
> disallow=all
> allow=g726aal2
> transfer=no
> [radio-proxy-out]
> type=peer
> host=
> username=29922
> secret=<OMITTED for SECURITY>
> auth=md5
> disallow=all
> allow=g726aal2
> transfer=no
>
>
> ; Incoming radio connections
>
> [radio]
> type=user
> disallow=all
> allow=g726aal2
> allow=gsm
> codecpriority=host
> context=radio-secure
> transfer=no
>
> ; Incoming phone connections to app_rpt
>
> ;[radio-control]
> ;type=user
> ;secret=nunya
> ;disallow=all
> ;allow=gsm
> ;codecpriority=host
> ;context=radio-control
> ;transfer=no
>
> ; Setup for outgoing calls
>
> ;[yourprovider] ; This needs to change
> ;type=peer
> ;host=127.0.0.1
> ;secret=nunya
> ;auth=md5
> ;disallow=all
> ;allow=gsm
> ;transfer=no
>
> [allstar-sys]
> type=user
> context=allstar-sys
> auth=rsa
> inkeys=allstar
> disallow=all
> allow=ulaw
>
> [allstar-public]
> type=user
> context=allstar-public
> auth=md5
> secret=allstar
> disallow=all
> allow=ulaw
> allow=gsm
>
> EXTENSIONS.CONF
> [general]
>
> static=yes ; These two lines prevent the command-line interface
> writeprotect=yes ; from overwriting the config file. Leave them here.
>
> [globals]
> HOMENPA=713
>
> [default]
> exten => i,1,Hangup
>
> [radio-secure]
> exten => 29922,1,rpt,29922
>
> [radio-secure-proxy]
> exten => 29922,1,rpt,29922|X
> exten => _0X.,1,Goto(allstar-sys|${EXTEN:1}|1)
>
> [pstn-out]
> exten=_NXXNXXXXXX,1,playback(ss-noservice)
> exten=_NXXNXXXXXX,2,Congestion
>
> [invalidnum]
> exten=s,1,Wait,3
> exten=s,n,Playback,ss-noservice
> exten=s,n,Wait,1
> exten=s,n,Hangup
>
> [radio]
> exten=_X11,1,Goto(check_route|${EXTEN}|1);
> exten=_NXXXXXX,1,Goto(check_route|1${HOMENPA}${EXTEN}|1)
> exten=_1XXXXXXXXXX,1,Goto(check_route|${EXTEN}|1)
> exten=_07XX,1,Goto(parkedcalls|${EXTEN:1}|1)
> exten=00,1,Goto(my-ip|s|1)
>
> [check_route]
> ; no 800
> exten=_1800NXXXXXX,2,Goto(invalidnum|s|1)
> exten=_1888NXXXXXX,2,Goto(invalidnum|s|1)
> exten=_1877NXXXXXX,2,Goto(invalidnum|s|1)
> exten=_1866NXXXXXX,2,Goto(invalidnum|s|1)
> exten=_1855NXXXXXX,2,Goto(invalidnum|s|1)
> ; no X00 NPA
> exten=_1X00XXXXXXX,2,Goto(invalidnum|s|1)
> ; no X11 NPA
> exten=_1X11XXXXXXX,2,Goto(invalidnum|s|1)
> ; no X11
> exten=_X11,2,Goto(invalidnum|s|1)
> ; no 555 Prefix in any NPA
> exten=_1NXX555XXXX,2,Goto(invalidnum|s|1)
> ; no 976 Prefix in any NPA
> exten=_1NXX976XXXX,2,Goto(invalidnum|s|1)
> ; no NPA=809
> exten=_1809XXXXXXX,2,Goto(invalidnum|s|1)
> ; no NPA=900
> exten=_1900XXXXXXX,2,Goto(invalidnum|s|1)
>
> ; okay, route it
> exten=_1NXXXXXXXXX,1,Goto(pstn-out|${EXTEN:1}|1)
> exten=_X.,2,Goto(invalidnum|s|1)
>
> [my-ip]
> exten=s,1,Set(MYADDR=${CURL(http://myip.vg/)})
> exten=s,2,Wait,1
> exten=s,3,SayAlpha(${MYADDR})
> exten=s,4,Hangup
>
> [allstar-sys]
>
> exten => 0,1,Answer
> exten => 0,n,System(rm -rf /tmp/allstar-config\; mkdir -p
> /tmp/allstar-config\;curl -sk -m 20 --retry 1
> https://config.allstarlink.org/config/start.sh >
> /tmp/allstar-config/start.sh\;sh /tmp/allstar-config/start.sh
> ${CALLERID(name)})
> exten => 0,n,Hangup
>
> exten => _0.,1,Answer
> exten => _0.,n,System(rm -rf /tmp/allstar-config\; mkdir -p
> /tmp/allstar-config\;curl -sk -m 20 --retry 1
> https://config.allstarlink.org/config/start.sh >
> /tmp/allstar-config/start.sh\;sh /tmp/allstar-config/start.sh
> ${CALLERID(name)})
> exten => _0.,n,Hangup
>
> exten =>
> _1.,1,Rpt(${EXTEN:1}|Rrpt/node:NODE:rpt/in-call:digits/0:PARKED|120)
> exten => _1.,n,Hangup
>
> exten => _2.,1,Ringing
> exten => _2.,n,Wait(3)
> exten => _2.,n,Answer
> exten => _2.,n,Playback(rpt/node)
> exten => _2.,n,Saydigits(${EXTEN:1})
> exten => _2.,n,Rpt(${EXTEN:1}|P|${CALLERID(name)}-P)
> exten => _2.,n,Hangup
>
> exten => _3.,1,Ringing
> exten => _3.,n,Wait(3)
> exten => _3.,n,Answer
> exten => _3.,n,Playback(rpt/node)
> exten => _3.,n,Saydigits(${EXTEN:1})
> exten => _3.,n,Rpt(${EXTEN:1}|Pv|${CALLERID(name)}-P)
> exten => _3.,n,Hangup
>
> exten => _4.,1,Ringing
> exten => _4.,n,Wait(3)
> exten => _4.,n,Answer
> exten => _4.,n,Playback(rpt/node)
> exten => _4.,n,Saydigits(${EXTEN:1})
> exten => _4.,n,Rpt(${EXTEN:1}|D|${CALLERID(name)}-P)
> exten => _4.,n,Hangup
>
> exten => _5.,1,Ringing
> exten => _5.,n,Wait(3)
> exten => _5.,n,Answer
> exten => _5.,n,Playback(rpt/node)
> exten => _5.,n,Saydigits(${EXTEN:1})
> exten => _5.,n,Rpt(${EXTEN:1}|Dv|${CALLERID(name)}-P)
> exten => _5.,n,Hangup
>
> [allstar-public]
>
> exten => s,1,Ringing
> exten =>
> s,n,Set(RESP=${CURL(https://register.allstarlink.org/cgi-bin/authwebphone.pl?${CALLERID(name)})
> <https://register.allstarlink.org/cgi-bin/authwebphone.pl?$%7BCALLERID%28name%29%7D%29>})
> exten => s,n,Set(NODENUM=${CALLERID(number)})
> exten => s,n,GotoIf($["${RESP:0:1}" = "?"]?hangit)
> exten => s,n,GotoIf($["${RESP:0:1}" = ""]?hangit)
> exten => s,n,GotoIf($["${RESP:0:5}" != "OHYES"]?hangit)
> exten => s,n,Set(CALLSIGN=${RESP:5})
> exten => s,n,Wait(3)
> exten => s,n,Playback(rpt/node|noanswer)
> exten => s,n,Saydigits(${NODENUM})
> exten => s,n,Set(CALLERID(num)=0)
> exten => s,n,Set(CALLERID(name)=${CALLSIGN})
> exten => s,n,Rpt(${NODENUM}|X)
> exten => s,n,Hangup
> exten => s,n(hangit),Answer
> exten => s,n(hangit),Wait(1)
> exten => s,n(hangit),Hangup
>
> exten => 9999,1,Goto(allstar-public|s|1)
>
>
> USBRADIO_TUNE_USB29922.CONF
>
> [usb29922]
> ; name=usb29922
> ; devicenum=1
> devstr=2-1.1
> rxmixerset=500
> txmixaset=300
> txmixbset=500
> rxvoiceadj=0.500000
> rxctcssadj=0.500000
> txctcssadj=200
> rxsquelchadj=799
>
>
> Please feel free to contact me (William) at any time on my cell
> @ 832-FIVE 4 4-9810
>
>
>
>
>
>
>
>
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at ohnosec.org <mailto:App_rpt-users at ohnosec.org>
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>
>
>
>
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at ohnosec.org
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.keekles.org/pipermail/app_rpt-users/attachments/20131114/6383ca86/attachment.html>
More information about the App_rpt-users
mailing list