[App_rpt-users] No TX audio upon reboot after initial install. Slow DMK URI LED Blink (Detailed info)
Johnny Keeker
cypresstower at yahoo.com
Thu Nov 14 04:44:43 UTC 2013
Im not sure exactly what your explaining so if you havent already
done so, try changing ctcssfrom=dsp to ctcssfrom=no.
I thought the blinking light on the URI was the PC heartbeat.
Check the CLI screen when its slow to make sure asterisk starts correctly.
Also check the sound driver. As root type this command to see if your URI is recognized;
[root at yournode~] dmesg
somewhere on the screen you should see something like this;
usb 3-2: configuration #1 chosen from 1 choice
input: C-Media Electronics Inc. USB PnP Sound Device as /class/input/input1
JK
From: William Schleppegrell <wschleppegrell at gmail.com>
To: app_rpt-users <app_rpt-users at ohnosec.org>
Sent: Wednesday, November 13, 2013 6:39 PM
Subject: [App_rpt-users] No TX audio upon reboot after initial install. Slow DMK URI LED Blink (Detailed info)
My node consists of an Intel NUC DCCP847DYE PC Which has an Intel Celeron™ Processor 847(1.10 GHz, 2M Cache)
It has 3 USB ports and Video / Audio out are supported by 2 HDMI ports which may be part of my problem.
•
Intel® HD Graphics
•
Dual HDMI Ports supporting dual independent display
Intel® High Definition Audio (Intel® HD Audio) via two
HDMI 1.4a outputs supporting 8 channel (7.1) digital audio
I am running a single node on this pc. The node is operating a UHF repeater. Two radios. Icom Commercial IC-F420 mobiles via a DMK URI.
I loaded ACID and my system ran fine until I rebooted. This is my second attempt at installation.
I will include my .conf files below. I have PL tones set on radios but am not using COR/COS. I utilize the software to detect PL to trigger TX/RX.
I have a slow blinking green LED on the DMK URI 2-3 flashes per second, when it has failed and is not sending audio to the TX radio(like now). And a nice fast blink pattern when it is working.
Ok...Oh the is keying up with a staticy transmission during ID's and when Flash is run in the radio-tune-menu, but not recognizable audio is heard.
RPT.CONF
[29922] ; Change this to your assigned node number
rxchannel=Radio/usb29922
duplex=2
erxgain=-3
etxgain=3
;controlstates=controlstates
scheduler=schedule29922
morse=morse29922
macro=macro29922
functions=functions29922
phone_functions=functions29922
link_functions=functions29922
telemetry=telemetry
wait_times=wait-times
context = radio
callerid = "Repeater" <0000000000>
idrecording = |iAE5YY
accountcode=RADIO
hangtime=100
althangtime=100
totime=170000
idtime=540000
politeid=3000
idtalkover=|iAE5YY
unlinkedct=ct2
remotect=ct3
linkunkeyct=ct8
;nolocallinkct=0
;eannmode=1
;connpgm=yourconnectprogram
;discpgm=yourdisconnectprogram
;lnkactenable=0
;lnkacttime=1800
;lnkactmacro=*52
;lnkacttimerwarn=30seconds
;remote_inact_timeout=1800
;remote_timeout=3600
nounkeyct=0
;holdofftelem=0
beaconing=0
;
; *** Status Reporting ***
;
; Uncomment the either group following two statpost lines to report the status of your node to stats.allstarlink.org
; depending on whether you are running ACID or Limey Linux.
; ** For ACID ***
statpost_program=/usr/bin/wget,-q,--timeout=15,--tries=1,--output-document=/dev/null
statpost_url=http://stats.allstarlink.org/uhandler.php ; Status updates
; ** For Limey Linux **
;statpost_program=/bin/wget,-q,--timeout=15,--tries=1,--output-document=/dev/null
;statpost_url=http://stats.allstarlink.org/uhandler.php ; Status updates
;
; Morse code parameters, these are common to all repeaters.
;
[morse29922]
speed=18
frequency=800
amplitude=4096
idfrequency=750
idamplitude=1024
[schedule29922]
;dtmf_function = m h dom mon dow ; ala cron, star is implied
[functions29922]
1=ilink,1
2=ilink,2
3=ilink,3
4=ilink,4
5=macro,1
70=ilink,5
71=ilink,6
72=ilink,7
73=ilink,15
74=ilink,16
75=ilink,8
80=status,1
81=status,2
6=autopatchup,noct=1,farenddisconnect=1,dialtime=20000 ; Autopatch up
0=autopatchdn ; Autopatch down
;989=cop,4
980=status,3
99=cop,6
; Place command macros here
[macro29922]
[telemetry]
ct1=|t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048)
ct2=|t(660,880,150,2048)
ct3=|t(440,0,150,4096)
ct4=|t(550,0,150,2048)
ct5=|t(660,0,150,2048)
ct6=|t(880,0,150,2048)
ct7=|t(660,440,150,2048)
ct8=|t(700,1100,150,2048)
remotetx=|t(1633,0,50,3000)(0,0,80,0)(1209,0,50,3000);
remotemon=|t(1209,0,50,2048)
cmdmode=|t(900,903,200,2048)
functcomplete=|t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)
patchup=rpt/callproceeding
[wait-times]
telemwait=2000
idwait=500
unkeywait=2000
calltermwait=2000
;
; This is where you define your nodes which cam be connected to.
;
[nodes]
; Note, if you are using automatic update for allstar link nodes,
; no allstar link nodes should be defined here. Only place a definition
; for your locak nodes, and private (off of allstar link) nodes here.
29922 = radio at 127.0.0.1/29922,NONE
; Memories for remote bases
[memory]
;00 = 146.580,100.0,m
;01 = 147.030,103.5,m+t
;02 = 147.240,103.5,m+t
;03 = 147.765,79.7,m-t
;04 = 146.460,100.0,m
;05 = 146.550,100.0,m
USBRADIO.CONF
[general]
[usb29922]
hdwtype=0
rxboost=1
txboost=1
rxctcssrelax=1
txctcssdefault=136.5
rxctcssfreqs=136.5
txctcssfreqs=136.5
;rxctcssoverride=0
carrierfrom=dsp
ctcssfrom=dsp
rxdemod=flat
txprelim=no
txlimonly=no
txtoctype=no
txmixa=composite
txmixb=no
invertptt=0
duplex=1
rxondelay=0
rxnoisefiltype=0
eeprom=0
#includeifexists custom/usbradio.conf
IAX.CONF
; Inter-Asterisk eXchange driver definition
;
;
[general]
bindport=4569
bindaddr=0.0.0.0
disallow=all
allow=gsm
allow=g726aal2
allow=ulaw
jitterbuffer=yes
forcejitterbuffer=yes
dropcount=2
maxjitterbuffer=4000
maxjitterinterps=10
resyncthreshold=1000
maxexcessbuffer=80
minexcessbuffer=10
jittershrinkrate=1
tos=0x1E
autokill=yes
delayreject=yes
;iaxthreadcount=30
;iaxmaxthreadcount=150
register=29922:<PASSWORD OMITTED>@register.allstarlink.org
IN EMAIL for SECURITY
[radio-proxy]
type=user
deny=0.0.0.0/0.0.0.0
permit=/255.255.255.255
context=radio-secure-proxy
disallow=all
allow=g726aal2
transfer=no
[radio-proxy-out]
type=peer
host=
username=29922
secret=<OMITTED for SECURITY>
auth=md5
disallow=all
allow=g726aal2
transfer=no
; Incoming radio connections
[radio]
type=user
disallow=all
allow=g726aal2
allow=gsm
codecpriority=host
context=radio-secure
transfer=no
; Incoming phone connections to app_rpt
;[radio-control]
;type=user
;secret=nunya
;disallow=all
;allow=gsm
;codecpriority=host
;context=radio-control
;transfer=no
; Setup for outgoing calls
;[yourprovider] ; This needs to change
;type=peer
;host=127.0.0.1
;secret=nunya
;auth=md5
;disallow=all
;allow=gsm
;transfer=no
[allstar-sys]
type=user
context=allstar-sys
auth=rsa
inkeys=allstar
disallow=all
allow=ulaw
[allstar-public]
type=user
context=allstar-public
auth=md5
secret=allstar
disallow=all
allow=ulaw
allow=gsm
EXTENSIONS.CONF
[general]
static=yes ; These two lines prevent the command-line interface
writeprotect=yes ; from overwriting the config file. Leave them here.
[globals]
HOMENPA=713
[default]
exten => i,1,Hangup
[radio-secure]
exten => 29922,1,rpt,29922
[radio-secure-proxy]
exten => 29922,1,rpt,29922|X
exten => _0X.,1,Goto(allstar-sys|${EXTEN:1}|1)
[pstn-out]
exten=_NXXNXXXXXX,1,playback(ss-noservice)
exten=_NXXNXXXXXX,2,Congestion
[invalidnum]
exten=s,1,Wait,3
exten=s,n,Playback,ss-noservice
exten=s,n,Wait,1
exten=s,n,Hangup
[radio]
exten=_X11,1,Goto(check_route|${EXTEN}|1);
exten=_NXXXXXX,1,Goto(check_route|1${HOMENPA}${EXTEN}|1)
exten=_1XXXXXXXXXX,1,Goto(check_route|${EXTEN}|1)
exten=_07XX,1,Goto(parkedcalls|${EXTEN:1}|1)
exten=00,1,Goto(my-ip|s|1)
[check_route]
; no 800
exten=_1800NXXXXXX,2,Goto(invalidnum|s|1)
exten=_1888NXXXXXX,2,Goto(invalidnum|s|1)
exten=_1877NXXXXXX,2,Goto(invalidnum|s|1)
exten=_1866NXXXXXX,2,Goto(invalidnum|s|1)
exten=_1855NXXXXXX,2,Goto(invalidnum|s|1)
; no X00 NPA
exten=_1X00XXXXXXX,2,Goto(invalidnum|s|1)
; no X11 NPA
exten=_1X11XXXXXXX,2,Goto(invalidnum|s|1)
; no X11
exten=_X11,2,Goto(invalidnum|s|1)
; no 555 Prefix in any NPA
exten=_1NXX555XXXX,2,Goto(invalidnum|s|1)
; no 976 Prefix in any NPA
exten=_1NXX976XXXX,2,Goto(invalidnum|s|1)
; no NPA=809
exten=_1809XXXXXXX,2,Goto(invalidnum|s|1)
; no NPA=900
exten=_1900XXXXXXX,2,Goto(invalidnum|s|1)
; okay, route it
exten=_1NXXXXXXXXX,1,Goto(pstn-out|${EXTEN:1}|1)
exten=_X.,2,Goto(invalidnum|s|1)
[my-ip]
exten=s,1,Set(MYADDR=${CURL(http://myip.vg/)})
exten=s,2,Wait,1
exten=s,3,SayAlpha(${MYADDR})
exten=s,4,Hangup
[allstar-sys]
exten => 0,1,Answer
exten => 0,n,System(rm -rf /tmp/allstar-config\; mkdir -p /tmp/allstar-config\;curl -sk -m 20 --retry 1 https://config.allstarlink.org/config/start.sh > /tmp/allstar-config/start.sh\;sh /tmp/allstar-config/start.sh ${CALLERID(name)})
exten => 0,n,Hangup
exten => _0.,1,Answer
exten => _0.,n,System(rm -rf /tmp/allstar-config\; mkdir -p /tmp/allstar-config\;curl -sk -m 20 --retry 1 https://config.allstarlink.org/config/start.sh > /tmp/allstar-config/start.sh\;sh /tmp/allstar-config/start.sh ${CALLERID(name)})
exten => _0.,n,Hangup
exten => _1.,1,Rpt(${EXTEN:1}|Rrpt/node:NODE:rpt/in-call:digits/0:PARKED|120)
exten => _1.,n,Hangup
exten => _2.,1,Ringing
exten => _2.,n,Wait(3)
exten => _2.,n,Answer
exten => _2.,n,Playback(rpt/node)
exten => _2.,n,Saydigits(${EXTEN:1})
exten => _2.,n,Rpt(${EXTEN:1}|P|${CALLERID(name)}-P)
exten => _2.,n,Hangup
exten => _3.,1,Ringing
exten => _3.,n,Wait(3)
exten => _3.,n,Answer
exten => _3.,n,Playback(rpt/node)
exten => _3.,n,Saydigits(${EXTEN:1})
exten => _3.,n,Rpt(${EXTEN:1}|Pv|${CALLERID(name)}-P)
exten => _3.,n,Hangup
exten => _4.,1,Ringing
exten => _4.,n,Wait(3)
exten => _4.,n,Answer
exten => _4.,n,Playback(rpt/node)
exten => _4.,n,Saydigits(${EXTEN:1})
exten => _4.,n,Rpt(${EXTEN:1}|D|${CALLERID(name)}-P)
exten => _4.,n,Hangup
exten => _5.,1,Ringing
exten => _5.,n,Wait(3)
exten => _5.,n,Answer
exten => _5.,n,Playback(rpt/node)
exten => _5.,n,Saydigits(${EXTEN:1})
exten => _5.,n,Rpt(${EXTEN:1}|Dv|${CALLERID(name)}-P)
exten => _5.,n,Hangup
[allstar-public]
exten => s,1,Ringing
exten => s,n,Set(RESP=${CURL(https://register.allstarlink.org/cgi-bin/authwebphone.pl?${CALLERID(name)})})
exten => s,n,Set(NODENUM=${CALLERID(number)})
exten => s,n,GotoIf($["${RESP:0:1}" = "?"]?hangit)
exten => s,n,GotoIf($["${RESP:0:1}" = ""]?hangit)
exten => s,n,GotoIf($["${RESP:0:5}" != "OHYES"]?hangit)
exten => s,n,Set(CALLSIGN=${RESP:5})
exten => s,n,Wait(3)
exten => s,n,Playback(rpt/node|noanswer)
exten => s,n,Saydigits(${NODENUM})
exten => s,n,Set(CALLERID(num)=0)
exten => s,n,Set(CALLERID(name)=${CALLSIGN})
exten => s,n,Rpt(${NODENUM}|X)
exten => s,n,Hangup
exten => s,n(hangit),Answer
exten => s,n(hangit),Wait(1)
exten => s,n(hangit),Hangup
exten => 9999,1,Goto(allstar-public|s|1)
USBRADIO_TUNE_USB29922.CONF
[usb29922]
; name=usb29922
; devicenum=1
devstr=2-1.1
rxmixerset=500
txmixaset=300
txmixbset=500
rxvoiceadj=0.500000
rxctcssadj=0.500000
txctcssadj=200
rxsquelchadj=799
Please feel free to contact me (William) at any time on my cell @ 832-FIVE 4 4-9810
_______________________________________________
App_rpt-users mailing list
App_rpt-users at ohnosec.org
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.keekles.org/pipermail/app_rpt-users/attachments/20131113/3b7d357f/attachment.html>
More information about the App_rpt-users
mailing list