[App_rpt-users] iaxrpt

[Bob]

Copied and pasted a line [radio-gui], changed the node number on the left,
but not the right.... it was 1 digit off like the example below. And to
think I went over it many times trying to figure out what I did incorrectly.
(sigh!)


[radio-gui]

exten => [node1],1,rpt([node1]|X)
exten => [node2],1,rpt([node1]|X)

 

Thanks,

Bob

kk6ecm

 

  _____  

From: app_rpt-users-bounces at ohnosec.org
[mailto:app_rpt-users-bounces at ohnosec.org] On Behalf Of REDBUTTON_CTRL
Sent: Sunday, April 06, 2014 5:10 AM
To: app_rpt-users at ohnosec.org
Subject: Re: [App_rpt-users] iaxrpt

 

We didn't see what the reply was. What was the typo???
inquiring minds want to know.

You should be able to set up 2 separate accounts in IAX_rpt and connect to
each node separately if you have all the settings in you server right.

in iax.conf:

; Setup for remote gui console

[gui]
type=user
context=radio-gui
auth=md5
secret=something    ; your password used in iax_rpt accounts
host=dynamic
disallow=all
allow=ulaw
allow=gsm
notransfer=yes


in extensions.conf:

; Setup for IAX_RPT gui console

[radio-gui]

exten => [node1],1,rpt([node1]|X)
exten => [node2],1,rpt([node2]|X)


note: "[node1]" = your first node# on the server and "[node2]" is the second
node.


Then make sure you have 2 accounts defined in IAX_Rpt, one for each node. 
In this case both accounts will use the same password. 
That should allow you to connect to either node and command it
independently.

Hope this helps.

Regards, 

Jon VA3RQ


On 4/6/2014 12:29 AM, Bob wrote: 

Thanks Mike... root cause, typo (sigh!) I may be getting smarter on this
stuff... still a lousy typist.

 

Bob

 

 

-------- Original Message --------
Subject: [App_rpt-users] iaxrpt
From: "Bob" < <mailto:kk6ecm at gmail.com> kk6ecm at gmail.com>
Date: Sun, April 06, 2014 12:01 am
To: < <mailto:app_rpt-users at ohnosec.org> app_rpt-users at ohnosec.org>

When I put my two nodes located on a single server into iaxrpt, and
separately connect to each, both activate the first node URI trasmit LED
when I "TRANSMIT" from either in iaxrpt; the node under
[radio-secure-proxy]. I have both nodes "register="ed in iax.conf under
[general] and as "exten => " under [radio-secure]. [radio-secure-proxy], and
"exten =*" under [radio-gui] in extensions.conf.

 

Did I do something incorrectly, or is this a limitation of iax and iaxrp?
I'd like to independently connect to either node on the server from iaxrpt.

 

By the way, under CLI, I can selectively activate, adjust, and identify
either URI, so I'm sure I don't have any USB confusion.

 

Thanks,

Bob

kk6ecm

 

 


  _____  


_______________________________________________
App_rpt-users mailing list
App_rpt-users at ohnosec.org
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users

To unsubscribe from this list please visit
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to
the bottom of the page. Enter your email address and press the "Unsubscribe
or edit options button"
You do not need a password to unsubscribe, you can do it via email
confirmation. If you have trouble unsubscribing, please send a message to
the list detailing the problem. 






_______________________________________________
App_rpt-users mailing list
App_rpt-users at ohnosec.org
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
 
To unsubscribe from this list please visit
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to
the bottom of the page. Enter your email address and press the "Unsubscribe
or edit options button"
You do not need a password to unsubscribe, you can do it via email
confirmation. If you have trouble unsubscribing, please send a message to
the list detailing the problem. 
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.keekles.org/pipermail/app_rpt-users/attachments/20140406/d16f866a/attachment.html>