[App_rpt-users] Remote Base setup
Robert A. Poff
wb3awj at comcast.net
Mon Dec 1 03:20:16 UTC 2014
Straight away, get rid of the "functions =functions-repeater" line.
Leave the "functions=functions-remote" line in.
On November 30, 2014 9:54:22 PM EST, Sam Nabkey <sam.nabkey at gmail.com> wrote:
>Okay--- Update....
>
>I have some sort of success on an ACID Install and It appears to almost
>work...
>
>IF I connect to the node, it tells me 'invalid Frequency' then the node
>number 'Connected'
>
>IF I poll the freq, it comes back as correct and the radio displays the
>proper freq of the init memory channel. no sweat.
>
>I can bump up down all around..
>
>IF i change freqs, it complains about 'invalid frequency' and the
>display
>doesn't change. IF I bump up or down the bumped frequency shows up on
>the
>radio, and if I bump the other direction it will be right on.
>
>Modes don't switch
>says it does, but doesn't.
>
>Ideas?
>
>Here is the rpt.conf from my remote node...
>
>[582]; Ada IC-706 Remote Base
>
>rxchannel=SimpleUSB/usb ; Rx audio/signalling channel
>
>functions = functions-remote
>functions = functions-repeater
>memory = memory
>
>remote = ic706
>ioport = /dev/ttyUSB0
>civaddr = 88
>authlevel=0
>
>[functions-remote]
>0=remote,1 ; Retrieve Memory
>1=remote,2 ; Set freq.
>2=remote,3 ; Set tx PL tone
>3=remote,4 ; Set rx PL tone
>6=remote,6 ; Set Mode 1=FM 2=USB 3=LSB
>4=AM
>40=remote,100 ; Rx PL off
>41=remote,101 ; Rx PL on
>42=remote,102 ; Tx PL off
>43=remote,103 ; Tx PL on
>44=remote,104 ; Low Power
>45=remote,105 ; Medium Power
>46=remote,106 ; High Power
>711=remote,107 ; Bump -20
>714=remote,108 ; Bump -100
>717=remote,109 ; Bump -500
>713=remote,110 ; Bump +20
>716=remote,111 ; Bump +100
>719=remote,112 ; Bump +500
>721=remote,113 ; Scan - slow
>724=remote,114 ; Scan - quick
>727=remote,115 ; Scan - fast
>723=remote,116 ; Scan + slow
>726=remote,117 ; Scan + quick
>729=remote,118 ; Scan + fast
>79=remote,119 ; Tune
>51=remote,5 ; Long status query
>52=remote,140 ; Short status query
>67=remote,210 ; Send a *
>69=remote,211 ; Send a #
>
>[nodes]
>581 = radio at 192.168.17.201/581,NONE
>582 = radio at 127.0.0.1/582,NONE,y
>
>[nodes](+)
>#include nodes.include
>
>[memory]
>init = 14.250,100.0,u ; 14.250MHz upper sideband
>00 = 146.460,100.0,sht
>01 = 146.940,100.0,-l
>02 = 14.250,100.0,u ; 14.250MHz upper sideband
>
>
>It is short and sweet.. Works the same if I use the default from the
>Dupral
>site.. works the same if I copy someone elses. I stripped all the
>stuff
>out of it that it seems not to care about to make it blatantly simple.
>
>Thanks for the help!
>
>
>
>On Sun, Nov 30, 2014 at 11:25 AM, <mike at midnighteng.com> wrote:
>
>>
>> As far as the BBB, you may not be defining the serial com correctly,
>but I
>> don't know that from what you have provided for info.
>>
>> Could you send your entire < [xxxnodeconfig] from rpt.conf > from
>your
>> acid install to me to understand what is or is not happening.
>>
>> It's hard to say a thing without more info. Probably a type error and
>you
>> need other set of eyes.
>> Also, is it defined as a stand alone RB node
>> (ie 29261 = radio at 127.0.0.1/29261,NONE,y ; ,y =remote base)
>>
>>
>> ...mike/kb8jnm
>>
>>
>> -------- Original Message --------
>> Subject: [App_rpt-users] Remote Base setup
>> From: Sam Nabkey <sam.nabkey at gmail.com>
>> Date: Sun, November 30, 2014 8:46 am
>> To: Allstar app_rpt-users Group <app_rpt-users at ohnosec.org>
>>
>> Hello all...
>>
>> I have been working on an agile remote base using an Icom 706. I
>have
>> seen a lot of posts and read a lot of ideas on using this radio.
>>
>> I first attemped using this under the Beagle Bone but I didn't have
>any
>> luck. SO I switched to an ACID install that was previously working
>as a
>> Repeater Node.
>>
>> I first added the remote stuff back to the rpt.conf - and the symptom
>> returned.
>>
>> The only working config has the line 'remote = ic706' commented out.
>>
>> Anyone have any ideas on why the USB interface won't start, or the
>node
>> would die just because the remote statement was added?
>>
>> I could use some pointers?
>>
>> --
>> *Samuel T. Nabkey - K8SN*
>>
>>
>>
>> ------------------------------
>> _______________________________________________
>> App_rpt-users mailing list
>> App_rpt-users at ohnosec.org
>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>>
>> To unsubscribe from this list please visit
>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll
>down
>> to the bottom of the page. Enter your email address and press the
>> "Unsubscribe or edit options button"
>> You do not need a password to unsubscribe, you can do it via email
>> confirmation. If you have trouble unsubscribing, please send a
>message to
>> the list detailing the problem.
>>
>>
>> _______________________________________________
>> App_rpt-users mailing list
>> App_rpt-users at ohnosec.org
>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>>
>> To unsubscribe from this list please visit
>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll
>down
>> to the bottom of the page. Enter your email address and press the
>> "Unsubscribe or edit options button"
>> You do not need a password to unsubscribe, you can do it via email
>> confirmation. If you have trouble unsubscribing, please send a
>message to
>> the list detailing the problem.
>>
>
>
>
>--
>
>*Samuel T. Nabkey - K8SN*
>
>
>*Project Manager / Repeater Owner | West Michigan Technical Group*
>
>DMR 3126098-100 | 442.175/R 103.5HZ | WX8GRR-B | IRLP 4168 | Allstar
>28789
>
> Work 616.257.1125 | Other 616.284.1358 | Fax 616.257.1101
>
>*sam.nabkey at gmail.com <sam.nabkey at gmail.com> | http://www.k8sn.org
><http://www.k8sn.org/> *
>
>
>------------------------------------------------------------------------
>
>_______________________________________________
>App_rpt-users mailing list
>App_rpt-users at ohnosec.org
>http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>
>To unsubscribe from this list please visit
>http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll
>down to the bottom of the page. Enter your email address and press the
>"Unsubscribe or edit options button"
>You do not need a password to unsubscribe, you can do it via email
>confirmation. If you have trouble unsubscribing, please send a message
>to the list detailing the problem.
--
Sent from my Android phone with K-9 Mail.
Please excuse my brevity and typing errors.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.keekles.org/pipermail/app_rpt-users/attachments/20141130/eff8d848/attachment.html>
More information about the App_rpt-users
mailing list