[App_rpt-users] Linking two nodes together

[Loren Tedford]

Yes Doug was looking to link via Internet for now till I can find some one
that really knows how to tune Duplexers.. lol... yea I have had bad look
with 7 different radio communication companies around here getting this
done either they lock open the repeater or you cant hear anyone through the
recieve side of the system.. So my goal was to setup a node at the house
for just RX use only and set up the Transmitter at the repeater site for
now.. Internet link them Voice over ip node to node.. I have two URIs and
two cables however one cable is a repeater cable suppose i could probably
use this on the RX side then use the other one for the transmitter.. Just
guessing Special Thanks goes out to Chris Curtis will try this thanks!! :)
Any other thoughts or suggestions with this project please let me know..

Loren Tedford (KC9ZHV)
Email: lorentedford at gmail.com
http://kc9zhv.lorentedford.com


On Fri, Dec 5, 2014 at 9:50 AM, Doug Crompton <doug at crompton.com> wrote:

> Do you mean linking via a normal Allstar link? or linking via RF. It is
> not clear what you are trying to do.
>
> You can link two nodes privately if you know the IP address and port of
> each node. You just enter the info for the OTHER node in the nodes section
> of rpt.conf. Assuming you have a good Internet path once this is entered
> and Asterisk is restarted you should be able to connect. Of course you also
> need the port forwards in the routers also.
>
> [nodes]
> ; Note, if you are using automatic update for allstar link nodes,
> ; no allstar link nodes should be defined here. Only place a definition
> ; for your local nodes, and private (off of allstar link) nodes here.
>
> 1998 = radio at ip.address.for.1999:port/1998,NONE
>
> This show one end. The other end would be just the opposite. Port is only
> needed if it is other than the default 4569.
>
>
>
> *73 DougWA3DSPhttp://www.crompton.com/hamradio
> <http://www.crompton.com/hamradio>*
>
>
> ------------------------------
> Date: Fri, 5 Dec 2014 01:52:39 -0600
> From: lorentedford at gmail.com
> To: app_rpt-users at ohnosec.org
> Subject: [App_rpt-users] Linking two nodes together
>
>
> Need to kinda get some examples of how to link two nodes together examples
> lets say node 1 is at the repeater site and node 2 is at my house and lets
> say that I cant get some one to tune up my duplexer properly.. what is the
> best way to link two nodes together to make my repeater at least
> functional..
>
> Thanks in advance
> Loren Tedford (KC9ZHV)
> Email: lorentedford at gmail.com
>
> http://kc9zhv.lorentedford.com
>
>
> _______________________________________________ App_rpt-users mailing list
> App_rpt-users at ohnosec.org
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe
> from this list please visit
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down
> to the bottom of the page. Enter your email address and press the
> "Unsubscribe or edit options button" You do not need a password to
> unsubscribe, you can do it via email confirmation. If you have trouble
> unsubscribing, please send a message to the list detailing the problem.
>
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at ohnosec.org
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>
> To unsubscribe from this list please visit
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down
> to the bottom of the page. Enter your email address and press the
> "Unsubscribe or edit options button"
> You do not need a password to unsubscribe, you can do it via email
> confirmation. If you have trouble unsubscribing, please send a message to
> the list detailing the problem.
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.keekles.org/pipermail/app_rpt-users/attachments/20141205/24bfcaa7/attachment.html>