[App_rpt-users] Need a clarification -- please

[mike at midnighteng.com]

Larry,

It was meant to be clear enough for those that stumble on it looking at
the mail archives.
Was not trying to be-little you in any way... sorry if I gave that
impression.

I can only add a fact of my own experience to this...

When I do a lot of switching between tx and rx on a node,
It sometimes gets a bit buggy,

I have always thought it was just something in my nodes or config but,

If you do the same, you might be on the watch for long hang time
building up on the connected node when in tx if you are switching back
and forth (tx/rx - *2/*3/*2) a lot.

I do not get this when I fully disconnect from mon *1/*71 and then con
for tx *3.

Perhaps someone else may have noticed this ?
I have not had the time to track it down as a system reboot (not
asterisk restart) is a quick fix when not at the console.

..mike/kb8jnm


> -------- Original Message --------
> Subject: Re: [App_rpt-users] Need a clarification -- please
> From: larry <larry at n7fm.com>
> Date: Fri, December 26, 2014 11:38 am
> To: app_rpt-users at ohnosec.org
> 
> 
> Thanks Stan and Mike,
> 
> Being able to toggle between modes is what I needed to know.
> 
> Mike,  I did understand about node numbers needing to be part of the *3 
> or *2 command but thanks for including that information in your explanation.
> Since I didn't include the full command structure inside my question 
> your answer may clarify that point for someone that I may have confused 
> by not doing so.
> 
> Larry - N7FM
> 
> 
> 
> 
> On 12/26/2014 01:57 AM, mike at midnighteng.com wrote:
> >
> > Larry,
> >
> > Yes for the most part...
> >
> > *2 29283  -con mon
> > *3 29283  -con tx-rx
> >
> > *3 alone will do nothing
> >
> > *1 29283  -disconnect only 29283
> > *1        -alone will do nothing
> > *71       -will disconnect every node connected to you mon or tx
> >
> > Command is the same live or macro.
> >
> > You do not need to disconnect (*71 or *1xxxxx) from monitor to switch
> > the same node to tx.
> >
> > Just issue the *3xxxxx
> >
> >
> > ...mike/kb8jnm
> >
> >
> >> -------- Original Message --------
> >> Subject: [App_rpt-users] Need a clarification -- please
> >> From: larry <larry at n7fm.com>
> >> Date: Fri, December 26, 2014 2:52 am
> >> To: app_rpt-users at ohnosec.org
> >>
> >>
> >> Going to create some macros but need to understand this sequence before
> >> hand.
> >>
> >> I want to create a macro that connects a node to another node/hub in the
> >> (*2 monitor only) mode.
> >>
> >> Later if I wish to change that same connection to a (*3 transceive) mode.
> >> Would a macro need to first issue a *1 disconnect and then reconnect
> >> with a *3 function or can you just issue the *3 command and toggle
> >> directly from monitor to transceive?
> >>
> >> I assume whatever sequence works in one direction would hold true if
> >> going in reverse from tranceive to monitor only.
> >>
> >> Thanks
> >> Larry - N7FM
> >>
> >>
> >>
> >> _______________________________________________
> >> App_rpt-users mailing list
> >> App_rpt-users at ohnosec.org
> >> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
> >>
> >> To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
> >> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
> > _______________________________________________
> > App_rpt-users mailing list
> > App_rpt-users at ohnosec.org
> > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
> >
> > To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
> > You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
> >
> 
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at ohnosec.org
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
> 
> To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.