[App_rpt-users] Error Message When Attempting to Connect to my hub

Sun Dec 28 17:28:42 UTC 2014

David there is a lot there but,

do you by chance update via webmin ?

if so, or even in any case, you might just do a update and recompile and
see where that leaves you.

Also, when you are trying to connect out,
to outside node would that be a internal to a node on other server
behind your nat or external allstar outside your nat.

Do you have correct "port forwarding" to static addresses even if
managed by router by mac id etc ?
Would need it at "cable modem/router" and a external router if you are
using one.

One last thing...
did you just switch to comcasts new dual wi-fi modem ?

Perhaps someone else will nail it but I can't see it from what is
stated.

...mike/kb8jnm

> -------- Original Message --------
> Subject: Re: [App_rpt-users] Error Message When Attempting to Connect to
> my	hub
> From: "David Dean K0PWO" <david at k0pwo.com>
> Date: Sun, December 28, 2014 12:00 pm
> To: "'Jim Duuuude'" <telesistant at hotmail.com>, "'Allstar app_rpt-users
> Group'" <app_rpt-users at ohnosec.org>
> 
> 
> This morning I followed the advice given by several members on the list. I added in the nodes section of both system
> 
>  
> 
> 40968 = radio at 192.168.20.1/40963,NONE <mailto:radio at 192.168.20.1/40963,NONE>  on the hub box
> 
> 41488 = radio at 192.168.20.1/41488,NONE <mailto:radio at 192.168.20.1/41488,NONE>  on the repeater box
> 
>  
> 
> And I still get connection failed error messages
> 
>  
> 
> Some back ground on what I have
> 
>  
> 
> *         Comcast internet
> 
> *         The Comcast supplied modem/router is bridged for modem gateway only
> 
> *         ASUS RT-AC68U Router which feeds a Cisco Switch which both boxes are currently plugged into
> 
> *         Node 41488 is my hub node and has port forwarding for port 4572 which it is assigned and configured
> 
> *          NODE 40968 is my repeater node and port forwarding for port 4569 which it is assigned and configured
> 
> *         Both machines for the moment have ssh of 222 (default) set
> 
> *         41488 (my hub) is using static ip (on my LAN) of 192.168.20.235
> 
> *         40968 (my repeater) is using static ip (on my LAN) of 192.168.20.243
> 
>  
> 
> The repeater was working fine up until about a month ago when It quit connecting to any nodes.
> 
>  
> 
> This morning I reset my router and reconfigured anything – no change
> 
> This morning I reformatted my repeater box and reconfigured using the Allstar Portal – no change
> 
>  
> 
> When I attempt to connect my repeater to my hub, which is on the same LAN with the node settings added that are listed above I get this error message on the CLI
> 
>  
> 
> [Dec 28 08:37:53] WARNING[2500]: chan_iax2.c:4328 handle_call_token: Address 192          .168.20.243 failed CallToken hash inspection
> 
> [Dec 28 08:37:55] WARNING[2508]: chan_iax2.c:4328 handle_call_token: Address 192          .168.20.243 failed CallToken hash inspection
> 
> [Dec 28 08:38:05] WARNING[2500]: chan_iax2.c:4328 handle_call_token: Address 192          .168.20.243 failed CallToken hash inspection
> 
> K0PWO_Hub*CLI> [Dec 28 08:37:53] WARNING[2500]: chan_iax2.c:4328 handle_call_tok          en: Address 192.168.20.243 failed CallToken hash inspection
> 
> K0PWO_Hub*CLI> [Dec 28 08:37:55] WARNING[2508]: chan_iax2.c:4328 handle_call_tok          en: Address 192.168.20.243 failed CallToken hash inspection
> 
> No such command '[Dec 28 08:37:53] WARNING[2500]: chan_iax2.c:4328 handle_call_t          oken: Address 192.168.20.243 failed CallToken hash inspection' (type 'help [Dec           28' for other possible commands)
> 
> No such command '[Dec 28 08:37:55] WARNING[2508]: chan_iax2.c:4328 handle_call_t          oken: Address 192.168.20.243 failed CallToken hash inspection' (type 'help [Dec           28' for other possible commands)
> 
> K0PWO_Hub*CLI> [Dec 28 08:38:05] WARNING[2500]: chan_iax2.c:4328 handle_call_tok          en: Address 192.168.20.243 failed CallToken hash inspection[Dec 28 08:37:53] WAR          NING[2500]: chan_iax2.c:4328 handle_call_token: Address 192.168.20.243 failed Ca          llToken hash inspection
> 
> K0PWO_Hub*CLI> [Dec 28 08:37:55] WARNING[2508]: chan_iax2.c:4328 handle_call_tok          en: Address 192.168.20.243 failed CallToken hash inspection
> 
> No such command '[Dec 28 08:38:05] WARNING[2500]: chan_iax2.c:4328 handle_call_t          oken: Address 192.168.20.243 failed CallToken hash inspection[Dec 28 08:37:53] W          ARNING[2500]: chan_iax2.c:4328 handle_call_token: Address 192.168.20.243 failed           CallToken hash inspection' (type 'help [Dec 28' for other possible commands)
> 
> No such command '[Dec 28 08:37:55] WARNING[2508]: chan_iax2.c:4328 handle_call_t          oken: Address 192.168.20.243 failed CallToken hash inspection' (type 'help [Dec           28' for other possible commands)
> 
> K0PWO_Hub*CLI> [Dec 28 08:38:05] WARNING[2500]: chan_iax2.c:4328 handle_call_tok          en: Address 192.168.20.243 failed CallToken hash inspectionexit
> 
> No such command '[Dec 28 08:38:05] WARNING[2500]: chan_iax2.c:4328 handle_call_t          oken: Address 192.168.20.243 failed CallToken hash inspectionexit' (type 'help [          Dec 28' for other possible commands)
> 
>  
> 
>  
> 
> Once again, anybody have any ideas on what is wrong? 
> 
>  
> 
> Thank you for any help provided.
> 
>  
> 
> David<hr>_______________________________________________
> App_rpt-users mailing list
> App_rpt-users at ohnosec.org
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
> 
> To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.