[App_rpt-users] Error Message When Attempting to Connect to my hub

Sun Dec 28 21:43:30 UTC 2014

on the hub box put
40968 = radio at 192.168.20.243:4569/40968,NONE

on the repeater box put
41488 = radio at 192.168.20.235:4572/41488,NONE

Don't forget to make sure your iax.conf has the appropriate changed
"bindport" to match the above.

reboot your router.
reboot both systems.

After a few minutes, it should work.
Chuck

On Sun, Dec 28, 2014 at 11:28 AM, <mike at midnighteng.com> wrote:

>
>
> David there is a lot there but,
>
> do you by chance update via webmin ?
>
> if so, or even in any case, you might just do a update and recompile and
> see where that leaves you.
>
> Also, when you are trying to connect out,
> to outside node would that be a internal to a node on other server
> behind your nat or external allstar outside your nat.
>
> Do you have correct "port forwarding" to static addresses even if
> managed by router by mac id etc ?
> Would need it at "cable modem/router" and a external router if you are
> using one.
>
> One last thing...
> did you just switch to comcasts new dual wi-fi modem ?
>
>
> Perhaps someone else will nail it but I can't see it from what is
> stated.
>
> ...mike/kb8jnm
>
>
>
> > -------- Original Message --------
> > Subject: Re: [App_rpt-users] Error Message When Attempting to Connect to
> > my    hub
> > From: "David Dean K0PWO" <david at k0pwo.com>
> > Date: Sun, December 28, 2014 12:00 pm
> > To: "'Jim Duuuude'" <telesistant at hotmail.com>, "'Allstar app_rpt-users
> > Group'" <app_rpt-users at ohnosec.org>
> >
> >
> > This morning I followed the advice given by several members on the list.
> I added in the nodes section of both system
> >
> >
> >
> > 40968 = radio at 192.168.20.1/40963,NONE <mailto:radio at 192.168.20.1/40963,NONE>
> on the hub box
> >
> > 41488 = radio at 192.168.20.1/41488,NONE <mailto:radio at 192.168.20.1/41488,NONE>
> on the repeater box
> >
> >
> >
> > And I still get connection failed error messages
> >
> >
> >
> > Some back ground on what I have
> >
> >
> >
> > *         Comcast internet
> >
> > *         The Comcast supplied modem/router is bridged for modem gateway
> only
> >
> > *         ASUS RT-AC68U Router which feeds a Cisco Switch which both
> boxes are currently plugged into
> >
> > *         Node 41488 is my hub node and has port forwarding for port
> 4572 which it is assigned and configured
> >
> > *          NODE 40968 is my repeater node and port forwarding for port
> 4569 which it is assigned and configured
> >
> > *         Both machines for the moment have ssh of 222 (default) set
> >
> > *         41488 (my hub) is using static ip (on my LAN) of 192.168.20.235
> >
> > *         40968 (my repeater) is using static ip (on my LAN) of
> 192.168.20.243
> >
> >
> >
> > The repeater was working fine up until about a month ago when It quit
> connecting to any nodes.
> >
> >
> >
> > This morning I reset my router and reconfigured anything – no change
> >
> > This morning I reformatted my repeater box and reconfigured using the
> Allstar Portal – no change
> >
> >
> >
> > When I attempt to connect my repeater to my hub, which is on the same
> LAN with the node settings added that are listed above I get this error
> message on the CLI
> >
> >
> >
> > [Dec 28 08:37:53] WARNING[2500]: chan_iax2.c:4328 handle_call_token:
> Address 192          .168.20.243 failed CallToken hash inspection
> >
> > [Dec 28 08:37:55] WARNING[2508]: chan_iax2.c:4328 handle_call_token:
> Address 192          .168.20.243 failed CallToken hash inspection
> >
> > [Dec 28 08:38:05] WARNING[2500]: chan_iax2.c:4328 handle_call_token:
> Address 192          .168.20.243 failed CallToken hash inspection
> >
> > K0PWO_Hub*CLI> [Dec 28 08:37:53] WARNING[2500]: chan_iax2.c:4328
> handle_call_tok          en: Address 192.168.20.243 failed CallToken hash
> inspection
> >
> > K0PWO_Hub*CLI> [Dec 28 08:37:55] WARNING[2508]: chan_iax2.c:4328
> handle_call_tok          en: Address 192.168.20.243 failed CallToken hash
> inspection
> >
> > No such command '[Dec 28 08:37:53] WARNING[2500]: chan_iax2.c:4328
> handle_call_t          oken: Address 192.168.20.243 failed CallToken hash
> inspection' (type 'help [Dec           28' for other possible commands)
> >
> > No such command '[Dec 28 08:37:55] WARNING[2508]: chan_iax2.c:4328
> handle_call_t          oken: Address 192.168.20.243 failed CallToken hash
> inspection' (type 'help [Dec           28' for other possible commands)
> >
> > K0PWO_Hub*CLI> [Dec 28 08:38:05] WARNING[2500]: chan_iax2.c:4328
> handle_call_tok          en: Address 192.168.20.243 failed CallToken hash
> inspection[Dec 28 08:37:53] WAR          NING[2500]: chan_iax2.c:4328
> handle_call_token: Address 192.168.20.243 failed Ca          llToken hash
> inspection
> >
> > K0PWO_Hub*CLI> [Dec 28 08:37:55] WARNING[2508]: chan_iax2.c:4328
> handle_call_tok          en: Address 192.168.20.243 failed CallToken hash
> inspection
> >
> > No such command '[Dec 28 08:38:05] WARNING[2500]: chan_iax2.c:4328
> handle_call_t          oken: Address 192.168.20.243 failed CallToken hash
> inspection[Dec 28 08:37:53] W          ARNING[2500]: chan_iax2.c:4328
> handle_call_token: Address 192.168.20.243 failed           CallToken hash
> inspection' (type 'help [Dec 28' for other possible commands)
> >
> > No such command '[Dec 28 08:37:55] WARNING[2508]: chan_iax2.c:4328
> handle_call_t          oken: Address 192.168.20.243 failed CallToken hash
> inspection' (type 'help [Dec           28' for other possible commands)
> >
> > K0PWO_Hub*CLI> [Dec 28 08:38:05] WARNING[2500]: chan_iax2.c:4328
> handle_call_tok          en: Address 192.168.20.243 failed CallToken hash
> inspectionexit
> >
> > No such command '[Dec 28 08:38:05] WARNING[2500]: chan_iax2.c:4328
> handle_call_t          oken: Address 192.168.20.243 failed CallToken hash
> inspectionexit' (type 'help [          Dec 28' for other possible commands)
> >
> >
> >
> >
> >
> > Once again, anybody have any ideas on what is wrong?
> >
> >
> >
> > Thank you for any help provided.
> >
> >
> >
> > David<hr>_______________________________________________
> > App_rpt-users mailing list
> > App_rpt-users at ohnosec.org
> > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
> >
> > To unsubscribe from this list please visit
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down
> to the bottom of the page. Enter your email address and press the
> "Unsubscribe or edit options button"
> > You do not need a password to unsubscribe, you can do it via email
> confirmation. If you have trouble unsubscribing, please send a message to
> the list detailing the problem.
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at ohnosec.org
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>
> To unsubscribe from this list please visit
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down
> to the bottom of the page. Enter your email address and press the
> "Unsubscribe or edit options button"
> You do not need a password to unsubscribe, you can do it via email
> confirmation. If you have trouble unsubscribing, please send a message to
> the list detailing the problem.
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.keekles.org/pipermail/app_rpt-users/attachments/20141228/cd6b91c7/attachment.html>