[App_rpt-users] audio radio to internet issue
REDBUTTON_CTRL
jrorke at cogeco.ca
Sat Feb 8 23:12:07 UTC 2014
OK If you are using packet port (discriminator) then set ctcssfrom= no
and carrierfrom=dsp
and
rxdemod=flat
That should get IT working.
Jon
On 2/8/2014 6:11 PM, ea8ee wrote:
> I use FT8900 with rear packet minidim with URI DMK
> so I will change
> ctssfrom=no/usb
> carrierfrom=usb or usbinvert/dsp( I think the yaesu use cor low but
> anyway the uri work nice with ptt and audio from internet the problem
> is only the audio from my rig to internet is deaf)
> rxdemod=flat/no
>
>
>
> 2014-02-08 22:43 GMT+00:00 REDBUTTON_CTRL <jrorke at cogeco.ca
> <mailto:jrorke at cogeco.ca>>:
>
> Oh and set ctcssfrom=no
> That way it wont be looking for a tone decoder output to let audio in.
> Jon RQ
>
>
> On 2/8/2014 5:39 PM, REDBUTTON_CTRL wrote:
>> If this is your usb radio.conf file then it is missing a couple
>> of things.
>>
>> You need the following:
>>
>> carrierfrom=usb (or usbinvert if your cor is active low)
>>
>> and the rxdemod must be set to speaker or flat
>>
>> That should get tit listening to rx audio to start.
>>
>> Jon VA3RQ
>>
>> On 2/8/2014 5:31 PM, ea8ee wrote:
>>> usb27305
>>> rxboost=1
>>> txboost=1
>>> rxctcssrelax=1
>>> txctcssdefault=88.5
>>> rxctcssfreqs=88.5
>>> ;rxctcssoverride=0
>>> ctcssfrom=usb
>>> rxdemod=no
>>> txprelim=no
>>> txlimonly=no
>>> txtoctype=notone
>>> txmixa=composite
>>> txmixb=composite
>>> invertptt=0
>>> duplex=0
>>> rxondelay=o
>>> rxnoisefiltype=0
>>> eeprom=1
>>>
>>> The DMK works nice in TX but in RX not receive nothing
>>>
>>>
>>>
>>> 2014-02-08 20:02 GMT+00:00 Doug Crompton <doug at crompton.com
>>> <mailto:doug at crompton.com>>:
>>>
>>> I think it found your adapter as you said you had audio in
>>> one direction. If not see below.
>>>
>>> Did you select the active usb device in the config utility
>>> before you tried to make changes?
>>>
>>>
>>> If the adapter is not being found at all try this....
>>>
>>> The following USB interfaces are defined in usbradio -
>>>
>>> #define C108_VENDOR_ID 0x0d8c
>>> #define C108_PRODUCT_ID 0x000c
>>> #define C108AH_PRODUCT_ID 0x013c
>>> #define C119_PRODUCT_ID 0x0008
>>> #define C119A_PRODUCT_ID 0x013a
>>> #define N1KDO_PRODUCT_ID 0x6a00
>>> #define C108_HID_INTERFACE 3
>>>
>>> When you boot up you should see one of these initialized in
>>> the messages. After boot do -
>>>
>>> dmesg | more
>>>
>>> and page through and see if it found your adapter.
>>>
>>> I am using the DMK and it looks like this -
>>>
>>> [root at WA3DSP_Allstar wa3dsp]# dmesg | grep Sound
>>> input: C-Media Electronics Inc. USB PnP Sound Device
>>> as /class/input/input0
>>> input,hidraw0: USB HID v1.00 Device [C-Media Electronics
>>> Inc. USB PnP Sound Device] on usb-0000:00:1d.0-1
>>>
>>> *73 Doug
>>> WA3DSP
>>> http://www.crompton.com/hamradio*
>>>
>>>
>>> ------------------------------------------------------------------------
>>> From: ea8ee1 at gmail.com <mailto:ea8ee1 at gmail.com>
>>> Date: Sat, 8 Feb 2014 19:14:56 +0000
>>> To: app_rpt-users at ohnosec.org <mailto:app_rpt-users at ohnosec.org>
>>> Subject: Re: [App_rpt-users] audio radio to internet issue
>>>
>>>
>>> I tried with cli and radio tune rxnoise and the pc says the
>>> device usb27305 currectly not active ! any suggestion?
>>>
>>>
>>> 2014-02-08 8:51 GMT+00:00 jose <ea8ee1 at gmail.com
>>> <mailto:ea8ee1 at gmail.com>>:
>>>
>>> Hi Doug! the ptt and audio from internet to radio works
>>> nicely the problem is about the audio from radio to
>>> internet not audio neither the node receive the dmtf
>>> from radio or webstransceiver
>>>
>>> El 08/02/2014 6:31, Doug Crompton escribió:
>>>
>>> You need to set -
>>>
>>> duplex=1 ; Simplex, no telelmetry
>>> duplex=0 ; Simplex, telelmetry
>>>
>>> in rpt.conf if you are running simplex.
>>>
>>> Also make sure the polarity is correct in your
>>> usbradio or simpleusb file for the PTT and COS if
>>> you are using it.
>>>
>>>
>>>
>>>
>>> _______________________________________________
>>> App_rpt-users mailing list App_rpt-users at ohnosec.org
>>> <mailto:App_rpt-users at ohnosec.org>
>>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To
>>> unsubscribe from this list please visit
>>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>>> and scroll down to the bottom of the page. Enter your email
>>> address and press the "Unsubscribe or edit options button"
>>> You do not need a password to unsubscribe, you can do it via
>>> email confirmation. If you have trouble unsubscribing,
>>> please send a message to the list detailing the problem.
>>>
>>>
>>>
>>>
>>> _______________________________________________
>>> App_rpt-users mailing list
>>> App_rpt-users at ohnosec.org <mailto:App_rpt-users at ohnosec.org>
>>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>>>
>>> To unsubscribe from this list please visithttp://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
>>> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
>>
>>
>> _______________________________________________
>> App_rpt-users mailing list
>> App_rpt-users at ohnosec.org <mailto:App_rpt-users at ohnosec.org>
>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>>
>> To unsubscribe from this list please visithttp://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
>> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
>
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at ohnosec.org <mailto:App_rpt-users at ohnosec.org>
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>
> To unsubscribe from this list please visit
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and
> scroll down to the bottom of the page. Enter your email address
> and press the "Unsubscribe or edit options button"
> You do not need a password to unsubscribe, you can do it via email
> confirmation. If you have trouble unsubscribing, please send a
> message to the list detailing the problem.
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.keekles.org/pipermail/app_rpt-users/attachments/20140208/e342ed11/attachment.html>
More information about the App_rpt-users
mailing list