[App_rpt-users] audio radio to internet issue

Sat Feb 8 23:45:22 UTC 2014

sorry the same problem not  audio from radio to internet yet


2014-02-08 23:12 GMT+00:00 REDBUTTON_CTRL <jrorke at cogeco.ca>:

>  OK  If you are using packet port (discriminator) then set ctcssfrom= no
> and carrierfrom=dsp
> and
> rxdemod=flat
>
> That should get IT working.
>
> Jon
>
>
> On 2/8/2014 6:11 PM, ea8ee wrote:
>
>   I use FT8900 with rear packet minidim with URI DMK
>  so I will change
>  ctssfrom=no/usb
>  carrierfrom=usb or usbinvert/dsp( I think the yaesu use cor low but
> anyway the uri work nice with ptt and audio from internet the problem is
> only the audio from my rig to internet is deaf)
>  rxdemod=flat/no
>
>
>
> 2014-02-08 22:43 GMT+00:00 REDBUTTON_CTRL <jrorke at cogeco.ca>:
>
>>  Oh and set ctcssfrom=no
>> That way it wont be looking for a tone decoder output to let audio in.
>> Jon RQ
>>
>>
>> On 2/8/2014 5:39 PM, REDBUTTON_CTRL wrote:
>>
>> If this is your usb radio.conf file then it is missing a couple of things.
>>
>> You need the following:
>>
>> carrierfrom=usb (or usbinvert if your cor is active low)
>>
>> and the rxdemod must be set to speaker or flat
>>
>> That should get tit listening to rx audio to start.
>>
>> Jon VA3RQ
>>
>> On 2/8/2014 5:31 PM, ea8ee wrote:
>>
>>          usb27305
>>  rxboost=1
>>  txboost=1
>>  rxctcssrelax=1
>>  txctcssdefault=88.5
>>  rxctcssfreqs=88.5
>>  ;rxctcssoverride=0
>>  ctcssfrom=usb
>>  rxdemod=no
>>  txprelim=no
>>  txlimonly=no
>>  txtoctype=notone
>>  txmixa=composite
>>  txmixb=composite
>>  invertptt=0
>>  duplex=0
>>  rxondelay=o
>>  rxnoisefiltype=0
>>  eeprom=1
>>
>> The DMK works nice in TX but in RX not receive nothing
>>
>>
>>
>> 2014-02-08 20:02 GMT+00:00 Doug Crompton <doug at crompton.com>:
>>
>>>  I think it found your adapter as you said you had audio in one
>>> direction. If not see below.
>>>
>>> Did you select the active usb device in the config utility before you
>>> tried to make changes?
>>>
>>>
>>> If the adapter is not being found at all try this....
>>>
>>> The following USB interfaces are defined in usbradio -
>>>
>>> #define C108_VENDOR_ID          0x0d8c
>>> #define C108_PRODUCT_ID         0x000c
>>> #define C108AH_PRODUCT_ID       0x013c
>>> #define C119_PRODUCT_ID         0x0008
>>> #define C119A_PRODUCT_ID        0x013a
>>> #define N1KDO_PRODUCT_ID        0x6a00
>>> #define C108_HID_INTERFACE      3
>>>
>>> When you boot up you should see one of these initialized in the
>>> messages. After boot do -
>>>
>>> dmesg | more
>>>
>>> and page through and see if it found your adapter.
>>>
>>> I am using the DMK and it looks like this -
>>>
>>> [root at WA3DSP_Allstar wa3dsp]# dmesg | grep Sound
>>> input: C-Media Electronics Inc.       USB PnP Sound Device as
>>> /class/input/input0
>>> input,hidraw0: USB HID v1.00 Device [C-Media Electronics Inc.       USB
>>> PnP Sound Device] on usb-0000:00:1d.0-1
>>>
>>>
>>>
>>> *73 Doug WA3DSP http://www.crompton.com/hamradio
>>> <http://www.crompton.com/hamradio>*
>>>
>>>
>>>  ------------------------------
>>> From: ea8ee1 at gmail.com
>>> Date: Sat, 8 Feb 2014 19:14:56 +0000
>>> To: app_rpt-users at ohnosec.org
>>> Subject: Re: [App_rpt-users] audio radio to internet issue
>>>
>>>
>>> I tried with  cli and radio tune rxnoise and the pc says the device
>>> usb27305 currectly not active ! any suggestion?
>>>
>>>
>>> 2014-02-08 8:51 GMT+00:00 jose <ea8ee1 at gmail.com>:
>>>
>>>  Hi Doug! the ptt and audio from internet to radio works nicely the
>>> problem is about the audio from radio to internet not audio neither the
>>> node receive the dmtf from radio or webstransceiver
>>>
>>> El 08/02/2014 6:31, Doug Crompton escribió:
>>>
>>> You need to set -
>>>
>>> duplex=1  ; Simplex, no telelmetry
>>> duplex=0  ; Simplex, telelmetry
>>>
>>> in rpt.conf if you are running simplex.
>>>
>>> Also make sure the polarity is correct in your usbradio or simpleusb
>>> file for the PTT and COS if you are using it.
>>>
>>>
>>>
>>>
>>>  _______________________________________________ App_rpt-users mailing
>>> list App_rpt-users at ohnosec.org
>>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To
>>> unsubscribe from this list please visit
>>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll
>>> down to the bottom of the page. Enter your email address and press the
>>> "Unsubscribe or edit options button" You do not need a password to
>>> unsubscribe, you can do it via email confirmation. If you have trouble
>>> unsubscribing, please send a message to the list detailing the problem.
>>>
>>
>>
>>
>> _______________________________________________
>> App_rpt-users mailing listApp_rpt-users at ohnosec.orghttp://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>>
>> To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
>> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
>>
>>
>>
>> _______________________________________________
>> App_rpt-users mailing listApp_rpt-users at ohnosec.orghttp://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>>
>> To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
>> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
>>
>>
>> _______________________________________________
>> App_rpt-users mailing list
>> App_rpt-users at ohnosec.org
>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>>
>> To unsubscribe from this list please visit
>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll
>> down to the bottom of the page. Enter your email address and press the
>> "Unsubscribe or edit options button"
>> You do not need a password to unsubscribe, you can do it via email
>> confirmation. If you have trouble unsubscribing, please send a message to
>> the list detailing the problem.
>>
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.keekles.org/pipermail/app_rpt-users/attachments/20140208/0ef7b550/attachment.html>