[App_rpt-users] no audio from URI

Tue Jun 3 21:33:55 UTC 2014

IT WORKS NOW
I tried the next pc (an older one) and it works fine without any config changes. It`s short before midnight and I must go to work tomorrow ☹
I will look the next days which CPUs and Chipsets I tried and doesn`t work and which one work now ok ?

Good n8 tom dh6mbt

Von: app_rpt-users-bounces at ohnosec.org [mailto:app_rpt-users-bounces at ohnosec.org] Im Auftrag von kk6ecm
Gesendet: Dienstag, 3. Juni 2014 23:13
An: App_rpt-users at ohnosec.org
Betreff: Re: [App_rpt-users] no audio from URI

Try amplifying the output of the URI in order to drive the speaker. If that does not work, I'd test the URI using a loopback connector and uridiag down loaded from http://www.dmkeng.com/images/URI-FAQs.pdf

Make sure Asterisk is stopped when uridiag is used. Service asterisk stop on the Linux command line. This is not a test to determine URI health, but the ability of the ACID build on your computer, and the ability to send audio to the URI.

Thanks,
Bob
kk6ecm

Sent from iPad

On Jun 3, 2014, at 2:51 PM, "torben at klimt-online.com<mailto:torben at klimt-online.com>" <torben at klimt-online.com<mailto:torben at klimt-online.com>> wrote:
Now i tried 3 different computers with 2 URI-Boards and 3 installs

-          SQL detect by DSP -> ok

-          DTMF reading -> ok

-          Transmitting by PTT -> ok

-          Sending audio -> NO

I have headphones connectet direct to the URI on Pins 13 (GND) and 22/23 -> no nothing ☹ ☹

Von: app_rpt-users-bounces at ohnosec.org<mailto:app_rpt-users-bounces at ohnosec.org> [mailto:app_rpt-users-bounces at ohnosec.org] Im Auftrag von kk6ecm
Gesendet: Dienstag, 3. Juni 2014 14:11
An: App_rpt-users at ohnosec.org<mailto:App_rpt-users at ohnosec.org>
Betreff: Re: [App_rpt-users] no audio from URI

Again, I'm not sure if it is your issue, but the chipset used in your board is of the same family as the one I seemed to have difficulty. When I chose a board with an older generation chipset (NM10, and not the 7x series), the audio worked good.

Thanks,
Bob
kk6ecm

Sent from iPad

On Jun 3, 2014, at 4:19 AM, "torben at klimt-online.com<mailto:torben at klimt-online.com>" <torben at klimt-online.com<mailto:torben at klimt-online.com>> wrote:
i take this box

http://www.intel.com/content/dam/www/public/us/en/documents/product-briefs/dc3217iye-product-brief.pdf

73 de tom dh6mbt
________________________________
Von: app_rpt-users-bounces at ohnosec.org<mailto:app_rpt-users-bounces at ohnosec.org> [app_rpt-users-bounces at ohnosec.org<mailto:app_rpt-users-bounces at ohnosec.org>] im Auftrag von kk6ecm [kk6ecm at gmail.com<mailto:kk6ecm at gmail.com>]
Gesendet: Dienstag, 3. Juni 2014 12:59
An: App_rpt-users at ohnosec.org<mailto:App_rpt-users at ohnosec.org>
Betreff: Re: [App_rpt-users] no audio from URI
I'm not sure of your issue, but your experience sounds like mine when I attempted to use a computer with a newer chipset, incompatible withe CentOS 5.10. That was Intel chipset NM 70. When I used a mother board with the older Intel chipset NM 10, I hade no audio issues. I discovered the issue when using DMK Engineering uridiag software on the ACID build (see URI FAQ on the DMK website re uridiag and loopback testing).

Thanks,
Bob
kk6ecm

Sent from iPad

On Jun 2, 2014, at 11:01 PM, "torben at klimt-online.com<mailto:torben at klimt-online.com>" <torben at klimt-online.com<mailto:torben at klimt-online.com>> wrote:
good morning,
i connect a headphone to the URI so we don`t need to search the problem on the Motorolas....

73...

________________________________
Von: David Morley [ab8tn1 at cox.net<mailto:ab8tn1 at cox.net>]
Gesendet: Dienstag, 3. Juni 2014 07:14
An: torben at klimt-online.com<mailto:torben at klimt-online.com>
Betreff: Re: [App_rpt-users] no audio from URI
Are the GM 360s the same as the GM 300s?  Do they have 16 pin connectors

Sent from my iPhone

On Jun 2, 2014, at 2:07 PM, "torben at klimt-online.com<mailto:torben at klimt-online.com>" <torben at klimt-online.com<mailto:torben at klimt-online.com>> wrote:
Hi all,
i think i have a little blackout ☹
I would like to set up a repeater with 2 GM360

<!--[if !supportLists]-->-          <!--[endif]-->SQL detect is ok

<!--[if !supportLists]-->-          <!--[endif]-->NF to another connectet repeater is ok

<!--[if !supportLists]-->-          <!--[endif]-->DTMF is ok (looks good on console)

-          PTT is ok
BUT there is no audio out from the URI on Port 22 and or 23 ☹
On a windows machine the URI works fine but on the asterisk there is no output
Any ideas ?
greetings
_______________________________________________
App_rpt-users mailing list
App_rpt-users at ohnosec.org<mailto:App_rpt-users at ohnosec.org>
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users

To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________
App_rpt-users mailing list
App_rpt-users at ohnosec.org<mailto:App_rpt-users at ohnosec.org>
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users

To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.keekles.org/pipermail/app_rpt-users/attachments/20140603/4760dae1/attachment.html>