[App_rpt-users] App_rpt-users Digest, Vol 69, Issue 27
Corey
kc7mrq at bresnan.net
Sun Nov 16 21:25:22 UTC 2014
Chuck,
I fixed all my issues. I didn't realize the difference between a NMEA &
Garmin sentence. I deselected all sentences that started with "P" in the
SNSRCFG program, reloaded the GPS file, and my warning went away.
I was able to update the firmware with your advice.
Thanks again for your help,
Corey
On 11/14/2014 11:51 PM, app_rpt-users-request at ohnosec.org wrote:
> Send App_rpt-users mailing list submissions to
> app_rpt-users at ohnosec.org
>
> To subscribe or unsubscribe via the World Wide Web, visit
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
> or, via email, send a message with subject or body 'help' to
> app_rpt-users-request at ohnosec.org
>
> You can reach the person managing the list at
> app_rpt-users-owner at ohnosec.org
>
> When replying, please edit your Subject line so it is more specific
> than "Re: Contents of App_rpt-users digest..."
>
>
> Today's Topics:
>
> 1. Re: EchoLink Policy Reminder (Johnny Keeker)
> 2. Voter board (Corey)
> 3. Re: Voter board (Chuck Henderson)
> 4. Re: Voter board (Chuck Henderson)
> 5. Re: Voter board (Chuck Henderson)
>
>
> ----------------------------------------------------------------------
>
> Message: 1
> Date: Fri, 14 Nov 2014 14:44:54 -0800
> From: Johnny Keeker <cypresstower at yahoo.com>
> To: kk6ecm <kk6ecm at gmail.com>, Kirk Just Kirk <wb6egr at gmail.com>
> Cc: app_rpt mailing list <app_rpt-users at ohnosec.org>
> Subject: Re: [App_rpt-users] EchoLink Policy Reminder
> Message-ID:
> <1416005094.33956.YahooMailBasic at web163604.mail.gq1.yahoo.com>
> Content-Type: text/plain; charset=iso-8859-1
>
> When they kill our accounts we'll say EchoStink Stunk
> --------------------------------------------
> On Tue, 11/11/14, Kirk Just Kirk <wb6egr at gmail.com> wrote:
>
> Subject: Re: [App_rpt-users] EchoLink Policy Reminder
> To: "kk6ecm" <kk6ecm at gmail.com>
> Cc: "app_rpt mailing list" <app_rpt-users at ohnosec.org>
> Date: Tuesday, November 11, 2014, 7:08 PM
>
> They can
> close/kill my account anytime. EchoStink sounds horrible
> most of the time...constant drivebys from dingalings that
> connect and disconnect over and over and say nothing...or
> connect at 3 in the morning and call CQ CQ. For 5
> minutes.....I am so tired of that shit I could delete it
> tonight.
>
>
> On Nov 11, 2014 2:00
> PM, "kk6ecm" <kk6ecm at gmail.com>
> wrote:
> Can anyone shed light
> on this Echolink requirement and Allstar? I'm not sure
> what makes us compliant. We have Echolink enabled on our
> repeater... I know of no way a non-ham could link in during
> an Echolink connection. Is there a way of setting app_rpt so
> an Echolink connection precludes all others? Also, Echolink
> has Apps for the PC, Android, and the iPhone/iPad... Their
> PC app (phones are RF, but not ham) seems to invalidate
> their rf only policy, although they do verify a license
> before granting a node number. What am I missing?
>
> Thanks,Bobkk6ecm
> Sent from iPad
>
> ---------- Forwarded
> message ----------
> From: EchoLink Support
> <support at echolink.org>
> Date: Wed, Sep 3, 2014 at 9:14 AM
> Subject: EchoLink Policy Reminder
> To:
>
>
> We wanted to remind you of an important item in
> EchoLink's access policies (which can be found online at
> http://www.echolink.org/access_policies.htm).
>
>
>
> In general, EchoLink does not permit cross-linking.
>
>
>
> More specifically, EchoLink does not permit cross-linking
> with other VoIP systems that can be accessed off-the-air
> (for example, directly from a PC or Web browser).? This is
> because other systems may have a validation procedure that
> is far less comprehensive than EchoLink's, and we want
> to continue to ensure that EchoLink is solely for use by
> licensed Amateur Radio operators around the world.
>
>
>
> Therefore, while excellent systems such as Zello, AllStar,
> eQSO, WIRES-II, etc. all serve an important purpose within
> the Amateur Radio community, our policy is that they cannot
> be directly connected to a registered EchoLink node.
>
>
>
> In other words, your node must function only as a direct RF
> gateway, and not as a cross-link to another system. If your
> node is reachable through another path, that path must be
> disabled when an EchoLink connection is in progress. For
> example, an EchoIRLP node is permitted, since it functions
> only as an RF gateway when an EchoLink connection is
> made.
>
>
>
> If you are running Asterisk with app_rpt and an EchoLink
> channel, be sure it is configured not to allow other VoIP
> connections when an EchoLink station is connected. If this
> isn't practical, please disable the EchoLink channel.
>
>
>
> Thanks for ensuring that your node adheres to this policy.
> In some cases we do restrict logins to be sure the policy is
> being followed.
>
>
>
> 73
>
> EchoLink Support
>
>
>
> (Note: This mailbox is not able to handle replies. For help
> and information, please see www.echolink.org/support.htm)
>
>
>
>
> _______________________________________________
>
> App_rpt-users mailing list
>
> App_rpt-users at ohnosec.org
>
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>
>
>
> To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
> and scroll down to the bottom of the page. Enter your email
> address and press the "Unsubscribe or edit options
> button"
>
> You do not need a password to unsubscribe, you can do it via
> email confirmation. If you have trouble unsubscribing,
> please send a message to the list detailing the problem.
>
> -----Inline Attachment Follows-----
>
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at ohnosec.org
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>
> To unsubscribe from this list
> please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
> and scroll down to the bottom of the page. Enter your
> email address and press the "Unsubscribe or edit
> options button"
> You do not need a
> password to unsubscribe, you can do it via email
> confirmation. If you have trouble unsubscribing, please send
> a message to the list detailing the problem.
>
>
>
> ------------------------------
>
> Message: 2
> Date: Fri, 14 Nov 2014 23:10:57 -0700
> From: Corey <kc7mrq at bresnan.net>
> To: app_rpt-users at ohnosec.org
> Subject: [App_rpt-users] Voter board
> Message-ID: <5466EE71.1090107 at bresnan.net>
> Content-Type: text/plain; charset=utf-8; format=flowed
>
>
> I built a through hole voter board and interfaced it to a GPS 18 LVC and
> my server. I set the board up as a master, transmit. The LED shows the
> GPS locked and 98 command shows the GPS,
> but I am getting the following error when telnetting into the board:
>
> Warning: GPS Data time period elapsed.
>
> The error is timestamped and occurs every second. I made sure the data
> format was NMEA per archived messages on here by connecting the GPS to
> SNSRCFG. The config appears to be set up correctly.
> What other areas do I need to look at to fix this warning?
>
> I did notice you can choose quite a few NMEA messages in the SNSRCFG
> profile. Does it matter if all are checked?
>
> I have a second issue with updating the firmware. The board is at Rev
> 1.41. I tried updating it, but haven't had any luck so far. Nothing
> happens when I click on the "capture target" button after resetting the
> voter board. The target ip is the voter board and the bootloader ip in
> the voter is my laptop with ENC_Loader.
>
> The IC(s) were originally programmed by a friend in another state so I
> never experienced what it take to do the initial programming.
>
>
> Thanks for your help,
> Corey
>
>
> ------------------------------
>
> Message: 3
> Date: Sat, 15 Nov 2014 00:27:46 -0600
> From: Chuck Henderson <rpt2 at chuck.midlandsnetworking.com>
> To: Corey <kc7mrq at bresnan.net>
> Cc: app_rpt mailing list <app_rpt-users at ohnosec.org>
> Subject: Re: [App_rpt-users] Voter board
> Message-ID:
> <CADEYVwj=UeTqkKzfERG8Oz+Rj+XZKYH649TCjaYYqtoUFoQ7og at mail.gmail.com>
> Content-Type: text/plain; charset="utf-8"
>
> set the bootloader IP to be the same as the voter board IP, or make it
> different than anything else on the network. It is the IP that the voter
> board uses when it is running the bootloader code. It can not have the
> same IP as your laptop. That will not work.
>
> On Sat, Nov 15, 2014 at 12:10 AM, Corey <kc7mrq at bresnan.net> wrote:
>
>> I built a through hole voter board and interfaced it to a GPS 18 LVC and
>> my server. I set the board up as a master, transmit. The LED shows the GPS
>> locked and 98 command shows the GPS,
>> but I am getting the following error when telnetting into the board:
>>
>> Warning: GPS Data time period elapsed.
>>
>> The error is timestamped and occurs every second. I made sure the data
>> format was NMEA per archived messages on here by connecting the GPS to
>> SNSRCFG. The config appears to be set up correctly.
>> What other areas do I need to look at to fix this warning?
>>
>> I did notice you can choose quite a few NMEA messages in the SNSRCFG
>> profile. Does it matter if all are checked?
>>
>> I have a second issue with updating the firmware. The board is at Rev
>> 1.41. I tried updating it, but haven't had any luck so far. Nothing happens
>> when I click on the "capture target" button after resetting the voter
>> board. The target ip is the voter board and the bootloader ip in the voter
>> is my laptop with ENC_Loader.
>>
>> The IC(s) were originally programmed by a friend in another state so I
>> never experienced what it take to do the initial programming.
>>
>>
>> Thanks for your help,
>> Corey
>> _______________________________________________
>> App_rpt-users mailing list
>> App_rpt-users at ohnosec.org
>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>>
>> To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/
>> mailman/listinfo/app_rpt-users and scroll down to the bottom of the page.
>> Enter your email address and press the "Unsubscribe or edit options button"
>> You do not need a password to unsubscribe, you can do it via email
>> confirmation. If you have trouble unsubscribing, please send a message to
>> the list detailing the problem.
> -------------- next part --------------
> An HTML attachment was scrubbed...
> URL: <http://ohnosec.org/pipermail/app_rpt-users/attachments/20141115/67ae2ac4/attachment-0001.html>
>
> ------------------------------
>
> Message: 4
> Date: Sat, 15 Nov 2014 00:36:19 -0600
> From: Chuck Henderson <rpt2 at chuck.midlandsnetworking.com>
> To: Corey <kc7mrq at bresnan.net>
> Cc: app_rpt mailing list <app_rpt-users at ohnosec.org>
> Subject: Re: [App_rpt-users] Voter board
> Message-ID:
> <CADEYVwiA4V6dkUSOhyNHFfOgor4yaKhojp9HweNzkJByNCutcw at mail.gmail.com>
> Content-Type: text/plain; charset="utf-8"
>
> An easy error is having the TX and RX swapped where you connect the GPS to
> the voter board. Try it the other way.
>
> On Sat, Nov 15, 2014 at 12:27 AM, Chuck Henderson <
> rpt2 at chuck.midlandsnetworking.com> wrote:
>
>> set the bootloader IP to be the same as the voter board IP, or make it
>> different than anything else on the network. It is the IP that the voter
>> board uses when it is running the bootloader code. It can not have the
>> same IP as your laptop. That will not work.
>>
>> On Sat, Nov 15, 2014 at 12:10 AM, Corey <kc7mrq at bresnan.net> wrote:
>>
>>> I built a through hole voter board and interfaced it to a GPS 18 LVC and
>>> my server. I set the board up as a master, transmit. The LED shows the GPS
>>> locked and 98 command shows the GPS,
>>> but I am getting the following error when telnetting into the board:
>>>
>>> Warning: GPS Data time period elapsed.
>>>
>>> The error is timestamped and occurs every second. I made sure the data
>>> format was NMEA per archived messages on here by connecting the GPS to
>>> SNSRCFG. The config appears to be set up correctly.
>>> What other areas do I need to look at to fix this warning?
>>>
>>> I did notice you can choose quite a few NMEA messages in the SNSRCFG
>>> profile. Does it matter if all are checked?
>>>
>>> I have a second issue with updating the firmware. The board is at Rev
>>> 1.41. I tried updating it, but haven't had any luck so far. Nothing happens
>>> when I click on the "capture target" button after resetting the voter
>>> board. The target ip is the voter board and the bootloader ip in the voter
>>> is my laptop with ENC_Loader.
>>>
>>> The IC(s) were originally programmed by a friend in another state so I
>>> never experienced what it take to do the initial programming.
>>>
>>>
>>> Thanks for your help,
>>> Corey
>>> _______________________________________________
>>> App_rpt-users mailing list
>>> App_rpt-users at ohnosec.org
>>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>>>
>>> To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/
>>> mailman/listinfo/app_rpt-users and scroll down to the bottom of the
>>> page. Enter your email address and press the "Unsubscribe or edit options
>>> button"
>>> You do not need a password to unsubscribe, you can do it via email
>>> confirmation. If you have trouble unsubscribing, please send a message to
>>> the list detailing the problem.
>>
>>
> -------------- next part --------------
> An HTML attachment was scrubbed...
> URL: <http://ohnosec.org/pipermail/app_rpt-users/attachments/20141115/853a9207/attachment-0001.html>
>
> ------------------------------
>
> Message: 5
> Date: Sat, 15 Nov 2014 00:51:05 -0600
> From: Chuck Henderson <rpt2 at chuck.midlandsnetworking.com>
> To: Corey <kc7mrq at bresnan.net>
> Cc: app_rpt mailing list <app_rpt-users at ohnosec.org>
> Subject: Re: [App_rpt-users] Voter board
> Message-ID:
> <CADEYVwh47howqRH1Ls++GhxryFd1QbYWDLZ3gufhSVhT2s9mtg at mail.gmail.com>
> Content-Type: text/plain; charset="utf-8"
>
> I should be asleep, or maybe I am. I just re-read your message and now I
> see you said that you do have GPS lock so ignore what I said about TX and
> RX.
> If you only have that problem when you telnet into the board, I have seen
> that when I have a poor quality network connection between the pc and the
> voter board. I think that the board gets too busy with re-sending on the
> ethernet and then has trouble reading the serial port data from the GPS.
> If they are on the same LAN then use a switch instead of a hub and make
> sure that duplex is correct for everything on the LAN segment. Also make
> sure that your netmask is set correctly (the same) on everything on the LAN.
> Also just go with the default NEMA messages, you do not need any other than
> the default.
>
> On Sat, Nov 15, 2014 at 12:36 AM, Chuck Henderson <
> rpt2 at chuck.midlandsnetworking.com> wrote:
>
>> An easy error is having the TX and RX swapped where you connect the GPS to
>> the voter board. Try it the other way.
>>
>> On Sat, Nov 15, 2014 at 12:27 AM, Chuck Henderson <
>> rpt2 at chuck.midlandsnetworking.com> wrote:
>>
>>> set the bootloader IP to be the same as the voter board IP, or make it
>>> different than anything else on the network. It is the IP that the voter
>>> board uses when it is running the bootloader code. It can not have the
>>> same IP as your laptop. That will not work.
>>>
>>> On Sat, Nov 15, 2014 at 12:10 AM, Corey <kc7mrq at bresnan.net> wrote:
>>>
>>>> I built a through hole voter board and interfaced it to a GPS 18 LVC and
>>>> my server. I set the board up as a master, transmit. The LED shows the GPS
>>>> locked and 98 command shows the GPS,
>>>> but I am getting the following error when telnetting into the board:
>>>>
>>>> Warning: GPS Data time period elapsed.
>>>>
>>>> The error is timestamped and occurs every second. I made sure the data
>>>> format was NMEA per archived messages on here by connecting the GPS to
>>>> SNSRCFG. The config appears to be set up correctly.
>>>> What other areas do I need to look at to fix this warning?
>>>>
>>>> I did notice you can choose quite a few NMEA messages in the SNSRCFG
>>>> profile. Does it matter if all are checked?
>>>>
>>>> I have a second issue with updating the firmware. The board is at Rev
>>>> 1.41. I tried updating it, but haven't had any luck so far. Nothing happens
>>>> when I click on the "capture target" button after resetting the voter
>>>> board. The target ip is the voter board and the bootloader ip in the voter
>>>> is my laptop with ENC_Loader.
>>>>
>>>> The IC(s) were originally programmed by a friend in another state so I
>>>> never experienced what it take to do the initial programming.
>>>>
>>>>
>>>> Thanks for your help,
>>>> Corey
>>>> _______________________________________________
>>>> App_rpt-users mailing list
>>>> App_rpt-users at ohnosec.org
>>>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>>>>
>>>> To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/
>>>> mailman/listinfo/app_rpt-users and scroll down to the bottom of the
>>>> page. Enter your email address and press the "Unsubscribe or edit options
>>>> button"
>>>> You do not need a password to unsubscribe, you can do it via email
>>>> confirmation. If you have trouble unsubscribing, please send a message to
>>>> the list detailing the problem.
>>>
>>>
> -------------- next part --------------
> An HTML attachment was scrubbed...
> URL: <http://ohnosec.org/pipermail/app_rpt-users/attachments/20141115/70101ed6/attachment.html>
>
> ------------------------------
>
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at ohnosec.org
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>
>
> End of App_rpt-users Digest, Vol 69, Issue 27
> *********************************************
>
More information about the App_rpt-users
mailing list