[App_rpt-users] RXDELAY in XIPAR

Lu Vencl vencl at att.net
Thu Sep 25 17:05:51 UTC 2014


Tried this but there was no effect. I placed it in URD.conf  I assume that is correct?

Lu Vencl

> On Sep 22, 2014, at 2:38 PM, Kevin Custer <kuggie at kuggie.com> wrote:
> 
> I'd have to dig a bit, but I believe this setting does not work as intended in XIPAR.   Please stand by.....
> 
> I'm sorry to have kept you waiting.
> 
> In XIPAR it's txrxdelay= 20 ms intervals.
> 
> Kevin
> 
> 
> 
>> On 9/22/2014 10:07 AM, Lu Vencl wrote:
>> Just made it long to test. But not effective. Probably only need 150 ms.  
>> 
>> Lu Vencl
>> 
>> On Sep 22, 2014, at 9:46 AM, Tim Sawyer <tim.sawyer at mac.com> wrote:
>> 
>>> Really? You need a 3 second delay? 
>>> --
>>> Tim WD6AWP
>>> 
>>>> On Sep 22, 2014, at 5:13 AM, Lu Vencl <vencl at att.net> wrote:
>>>> 
>>>> I have a XIPAR node that needs a little support with pulseback removal. Never had to utilize this before, but when looking in URD.conf, I don’t see the rxdelay= parameter like I do on ACID builds. I went ahead and inserted the command into the file, but there does not seem to be any action.
>>>> Can someone confirm the parameter and placement?
>>>> Here is my example:
>>>> [usb]
>>>>  
>>>> hdwtype=0           ; 0=std,1=dev
>>>> eeprom=0            ; unless you have a cable w/eeprom
>>>> duplex=0            ; 0=simplex, 1=duplex
>>>> invertptt=0
>>>> ;minsigproc=0        ; minimal signal processing
>>>> ;sendvoter=0        ; 0=default, no voter rssi, 1=enable voter rssi
>>>>  
>>>> carrierfrom=usbinvert     ; no,usb,usbinvert,dsp,vox
>>>> ctcssfrom=no        ; no,usb,dsp
>>>> rxondelay=3000              ; Gets rid of the pulseback problem
>>>> ;rxboost=1           ; rx input boost of 20dB
>>>> rxboost=0            ; no boost
>>>> rxdemod=flat        ; no,speaker,flat
>>>> txprelim=0          ; 1 = pre-emphasize and limit
>>>>  
>>>> txmixa=voice        ; no,voice,tone,composite
>>>> txmixb=tone         ; no,voice,tone,composite,auxvoice
>>>>  
>>>> ;txctcssdefault=77.0
>>>> ;rxctcssfreqs=77.0;
>>>> ;txctcssfreqs=77.0;
>>>> txtoctype=notone;  
>>>>  
>>>> rxsquelchdelay=900    ; delayline in ms carrier squelch tail eliminator
>>>> rxnoisefiltype=0    ; 0 for +/-5KHz, 2 for +/-2.5KHz systems
>>>>  
>>>>  
>>>> Lu,
>>>> KA4EPS
>>>> _______________________________________________
>>>> App_rpt-users mailing list
>>>> App_rpt-users at ohnosec.org
>>>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>>>> 
>>>> To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
>>>> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. 
>> 
>> 
>> _______________________________________________
>> App_rpt-users mailing list
>> App_rpt-users at ohnosec.org
>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>> 
>> To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
>> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. 
>> 
>> 
>> No virus found in this message.
>> Checked by AVG - www.avg.com
>> Version: 2014.0.4765 / Virus Database: 4025/8255 - Release Date: 09/22/14
>> 
> 
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.keekles.org/pipermail/app_rpt-users/attachments/20140925/4963754f/attachment.html>


More information about the App_rpt-users mailing list