[App_rpt-users] RTCM problem

[R Dahl]

Hi,
Ive been struggling for weeks trying to use the dsp squelch.  The sql and
diode calibration routine seems to work like the book says as well as
setting all the rx/tx levels. The problem is when I set the squelch pot
which seems to do nothing at all.  It all works as I believe it should when
using ext COR from the radio. Repeat and echolink and offline functions all
work.  It seems odd(to me) that the sql pot setting always returns zero.
Main and status displays are below, followed by voter.conf
Any suggestions?
Ross

1  - Serial # (1234) (which is MAC ADDR 00:04:A3:00:04:D2)
2  - VOTER Server Address (FQDN) (10.0.0.140)
3  - VOTER Server Port (667),  4  - Local Port (Override) (0)
5  - Client Password (xxxx),  6  - Host Password (xxxx)
7  - Tx Buffer Length (3000)
8  - GPS Data Protocol (0=NMEA, 1=TSIP) (0)
9  - GPS Serial Polarity (0=Non-Inverted, 1=Inverted) (0)
10 - GPS PPS Polarity (0=Non-Inverted, 1=Inverted, 2=NONE) (2)
11 - GPS Baud Rate (4800)
12 - External CTCSS (0=Ignore, 1=Non-Inverted, 2=Inverted) (2)
13 - COR Type (0=Normal, 1=IGNORE COR, 2=No Receiver) (1)
14 - Debug Level (0)
15  - Alt. VOTER Server Address (FQDN) ()
16  - Alt. VOTER Server Port (Override) (0)
17  - DSP/BEW Mode NOT SUPPORTED
18 - "Duplex Mode 3" (0=DISABLED, 1-255 Hang Time) (1/10 secs) (0)
19 - Simulcast Launch Delay (0) (approx 200 ns, 5 = 1us, > 0 to ENA SC)
20 - Ext. CTCSS Input Threshold (850) (0-1023)
97 - RX Level,  98 - Status,  99 - Save Values to EEPROM
i - IP Parameters menu, o - Offline Mode Parameters menu
q - Disconnect Remote Console Session, r - reboot system, d - diagnostics

Enter Selection (1-20,97-99,r,q,d) :


----98----
S/W Version: 1.46 03/04/2014
System Uptime: 15834.4 Secs
IP Address: 10.0.0.134
Netmask: 255.255.255.0
Gateway: 10.0.0.1
Primary DNS: 10.0.0.1
Secondary DNS: 8.8.4.4
DHCP: 1
VOTER Server IP: 10.0.0.140
VOTER Server UDP Port: 667
OUR UDP Port: 667
GPS Lock: 0
Connected: 1
COR: 1
EXT CTCSS IN: 1
PTT: 0
RSSI: 255
Current Samples / Sec.: 0
Current Peak Audio Level: 58800
Squelch Noise Gain Value: 14, Diode Cal. Value: 43, SQL pot 0

Press The Any Key (Enter) To Continue

----voter.conf---
[general]
port = 667
buflen = 500
password = xxxx

[40526]
40526 = xxxx,nodeemp,transmit,mulaw
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.keekles.org/pipermail/app_rpt-users/attachments/20150613/d6698662/attachment.html>