[App_rpt-users] App_rpt-users Digest, Vol 86, Issue 42

[Jesse Lloyd]

0 0 0 0 on the pins is ch 1 so you get 16 channels with 4 bits, theres no way to program a M216 to power up on ch 1 in the RSS. Home revert is a later feature in the CM & CDM series and you need to use the ignition sense to turn those on/off to reliably get it to work. Sometimes it works by resetting power, but I've had problems in some vehicles if it gets in a brown out condition on boot (engine crank). 

If you program one pin to "channel steer 1" (LSB) and momentarily pull it low the radio should go to channel one. 

If you want to steer up to 8 channels then you need 3 bits and pull all 3 to ground momentarily after bootup. Externally a time delayed one shot relay would do it, use diodes to isolate each input. 


Jesse

> On Apr 13, 2016, at 9:04 AM, Jeff Carrier <k0jsc.jeff at gmail.com> wrote:
> 
> Skyler, 
> 
> Channel steering should give you 15 channels using 4 pins for steering.  I know the CDM and the GM300's work this way.
> 
>> On Wed, Apr 13, 2016 at 10:00 AM, <app_rpt-users-request at ohnosec.org> wrote:
>> Send App_rpt-users mailing list submissions to
>>         app_rpt-users at ohnosec.org
>> 
>> To subscribe or unsubscribe via the World Wide Web, visit
>>         http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>> or, via email, send a message with subject or body 'help' to
>>         app_rpt-users-request at ohnosec.org
>> 
>> You can reach the person managing the list at
>>         app_rpt-users-owner at ohnosec.org
>> 
>> When replying, please edit your Subject line so it is more specific
>> than "Re: Contents of App_rpt-users digest..."
>> 
>> 
>> Today's Topics:
>> 
>>    1. Reset to channel 1 on radius (Skyler F)
>> 
>> 
>> ----------------------------------------------------------------------
>> 
>> Message: 1
>> Date: Tue, 12 Apr 2016 22:30:23 -0600
>> From: Skyler F <electricity440 at gmail.com>
>> To: "app_rpt-users at ohnosec.org" <app_rpt-users at ohnosec.org>
>> Subject: [App_rpt-users] Reset to channel 1 on radius
>> Message-ID:
>>         <CAJNyT08s-8MODP=r2gVFykAJ8F9NFycWd9OmrgpYnLensR6-gQ at mail.gmail.com>
>> Content-Type: text/plain; charset="utf-8"
>> 
>> AllStar Remote base wise, I am using some radius radios (m216 for VHF,
>> SM120 UHF). The VHF one does have Channel steer option on the software, but
>> I don't get to use every channel that the radio has :( only 8 instead of
>> 16. With the amount of repeaters here in Denver , I need as many channels
>> as I can get!
>> 
>> I can easily simulate key presses, but I would like a reliable way to reset
>> the channel back to original state. These radius radios remember the
>> channel they were on after a power cycle (unfortunately, in my case). Is
>> there any way to force it to go back to channel one?
>> 
>> 73,
>> Skyler KD?WHB
>> -------------- next part --------------
>> An HTML attachment was scrubbed...
>> URL: <http://ohnosec.org/pipermail/app_rpt-users/attachments/20160412/2a9381ee/attachment-0001.html>
>> 
>> ------------------------------
>> 
>> _______________________________________________
>> App_rpt-users mailing list
>> App_rpt-users at ohnosec.org
>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>> 
>> 
>> End of App_rpt-users Digest, Vol 86, Issue 42
>> *********************************************
> 
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at ohnosec.org
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
> 
> To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.keekles.org/pipermail/app_rpt-users/attachments/20160413/5528ed15/attachment.html>