[App_rpt-users] RX Input Adjust Failed

[kk6ecm]

No change... whenever I have ctcssfrom=no, the PTT on the URIx is active,
and app_rpt won't take DTMF commands. When I switch back to
ctcssfrom=usbinvert, all works normally, however, that configuration does
not work with my substitute receiver.

Thanks,
Bob
kk6ecm
73

-----Original Message-----
From: app_rpt-users-bounces at ohnosec.org
[mailto:app_rpt-users-bounces at ohnosec.org] On Behalf Of REDBUTTON_CTRL
Sent: Sunday, May 22, 2016 11:21 AM
To: app_rpt-users at ohnosec.org
Subject: Re: [App_rpt-users] RX Input Adjust Failed

Comment out the ctcss tones listed.
J

On 5/22/2016 2:35 PM, kk6ecm wrote:
> I discovered app_rpt does not like ctcssfrom=no. Why? (I'm using DIAL).
>
> What am I missing?
>
> Thanks,
> Bob
> kk6ecm
> 73
>
> -----Original Message-----
> From: kk6ecm [mailto:kk6ecm at gmail.com]
> Sent: Sunday, May 22, 2016 10:37 AM
> To: 'app_rpt-users at ohnosec.org'
> Subject: RX Input Adjust Failed
>
> What could cause the Error: RX Input Adjust Failed?
>
> DONE tries=12, setting=1000, meas=58, sqnoise=13
> ERROR: RX INPUT ADJUST FAILED.
>
> No RF input to the radio.
>
> I'm attempting to setup a substitute receiver for testing, but am
> experiencing difficulty setting it up, and not wanting to make a switch to
> simpleusb, thus making the minimum number of changes.
>
> The substitute receiver (Yaesu FT-1500M) is detecting CTCSS, with USB COR
> out, and I'm using the speaker output. (see below conf file)
>
> Any thoughts?
>
> Thanks,
> Bob
> kk6ecm
> 73
>
>
> from usbradio_tune...
>
> hdwtype=0	
> rxboost=1
> txboost=1
> rxctcssrelax=1
> txctcssdefault=107.2
> rxctcssfreqs=107.2
> txctcssfreqs=107.2
> ;rxctcssoverride=0
> ;carrierfrom=dsp
> carrierfrom=usb   ;dsp
> ctcssfrom=no    ;usbinvert
> rxdemod=speaker ;flat
> txprelim=no
> txlimonly=no
> txtoctype=notone
> txmixa=composite
> txmixb=no
> invertptt=0
> duplex=1
> rxondelay=0
> rxnoisefiltype=0
> eeprom=0
>
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at ohnosec.org
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>
> To unsubscribe from this list please visit
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to
the bottom of the page. Enter your email address and press the "Unsubscribe
or edit options button"
> You do not need a password to unsubscribe, you can do it via email
confirmation. If you have trouble unsubscribing, please send a message to
the list detailing the problem.
>
_______________________________________________
App_rpt-users mailing list
App_rpt-users at ohnosec.org
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users

To unsubscribe from this list please visit
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to
the bottom of the page. Enter your email address and press the "Unsubscribe
or edit options button"
You do not need a password to unsubscribe, you can do it via email
confirmation. If you have trouble unsubscribing, please send a message to
the list detailing the problem.