[App_rpt-users] ctcss Encode Issues

[Michael "Lee" Lockwood]

Steve Mahler:  The RX ctcss tones I'm using are being decoded by the dsp.
I get verification of that when running debug in app_rpt.

Neil:  I'd like to have the same ctcss tone transmitted for the "repeater
tail" and courtesy tone the same amount of time it's set in the rpt.conf
file.  I think I have mine set to 1.5 seconds.

On Wed, Aug 9, 2017 at 11:01 AM, Neil k8it <k8it at cac.net> wrote:

> for how long after a giben ctcss tone is reciebed do you want to use the
> same ctcss tx tone
> when would it reset to the 151.4 tone
> Thanks
> 73 Neil Sablatzky  K8IT
> Allstar Node 41838 KITLINK
> Allstar Node 42087 KITLINK HUB
> IRLP Node exp0068
> Echolink K8IT-L
> WIRES-X K8IT 11479 Room 21479
>
> *From:* Michael "Lee" Lockwood <michael at lockwood.us.com>
> *Sent:* Wednesday, August 09, 2017 11:12 AM
> *To:* app_rpt-users at lists.allstarlink.org
> *Subject:* Re: [App_rpt-users] ctcss Encode Issues
>
> A follow up to my previous email:
>
> I have multiple ctcss tone frequencies in usbradio.conf.  app_rpt is
> decoding the incoming CTCSS (confirmed using debug), and it transmits CTCSS
> while someone is actively keying the repeater.  However, as soon as they
> release PTT, app_rpt stops transmitting the corresponding CTCSS tone that
> was being used, and reverts to the default tone instead.
>
> So, if I key the repeater using 146.2, it broadcasts out using 146.2 and
> other radios hear audio just fine.  But, as soon as I release PTT on the
> mobile/portable radio, the squelch tail is broadcast using 151.4, not
> 146.2.  This results in the users programmed with 146.2 not hearing the
> courtesy tone or squelch tail.
>
> Has anyone else run in to this issue?
>
> Here's my usbradio.conf file again:
>
> [usb]
>
> hdwtype=0
> rxboost=1
> txboost=1
> rxctcssrelax=1
> txctcssdefault=151.4
> rxctcssfreqs=146.2,141.3,151.4
> txctcssfreqs=146.2,141.3,151.4
> ;rxctcssoverride=0
> carrierfrom=usb
> ctcssfrom=dsp
> rxdemod=flat
> txprelim=yes
> txlimonly=no
> txtoctype=phase
> txmixa=composite
> txmixb=0
> invertptt=0
> duplex=1
> rxondelay=0
> rxnoisefiltype=0
> eeprom=0
>
>
>
> On Mon, Aug 7, 2017 at 7:41 PM, Michael "Lee" Lockwood <
> michael at lockwood.us.com> wrote:
>
>> Hello,
>> I am unable to get any ctcss to be encoded during transmit, except for
>> the tone frequency that's entered in to the txctcssdetault field.  If I
>> change that tone, the new value gets transmitted.  However, all of the
>> other tones in the txctcssfreqs are being ignored.  However, I do know that
>> the rxctcssfreqs values are being decoded.  If I transmit in to the
>> repeater using a tone not listed, or without a tone, app_rpt ignores it and
>> does not repeat and key up the transmitter.  Any assistance is greatly
>> appreciated.  Thanks in advance!
>>
>> Here's what's in my usbradio.conf
>>
>> [usb]
>>
>> hdwtype=0
>> rxboost=1
>> txboost=1
>> rxctcssrelax=1
>> txctcssdefault=151.4
>> rxctcssfreqs=146.2,141.3,151.4
>> txctcssfreqs=146.2,141.3,151.4
>> ;rxctcssoverride=0
>> carrierfrom=usb
>> ctcssfrom=dsp
>> rxdemod=flat
>> txprelim=yes
>> txlimonly=no
>> txtoctype=phase
>> txmixa=composite
>> txmixb=0
>> invertptt=0
>> duplex=1
>> rxondelay=0
>> rxnoisefiltype=0
>> eeprom=0
>>
>>
>> --
>>
>> *Michael "Lee" Lockwood*
>> michael at lockwood.us.com
>>
>
>
>
> --
>
> *Michael "Lee" Lockwood*
> michael at lockwood.us.com
>
> ------------------------------
>
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at lists.allstarlink.org
> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
>
> To unsubscribe from this list please visit http://lists.allstarlink.org/
> cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of
> the page. Enter your email address and press the "Unsubscribe or edit
> options button"
> You do not need a password to unsubscribe, you can do it via email
> confirmation. If you have trouble unsubscribing, please send a message to
> the list detailing the problem.
>
>
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at lists.allstarlink.org
> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
>
> To unsubscribe from this list please visit http://lists.allstarlink.org/
> cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of
> the page. Enter your email address and press the "Unsubscribe or edit
> options button"
> You do not need a password to unsubscribe, you can do it via email
> confirmation. If you have trouble unsubscribing, please send a message to
> the list detailing the problem.
>



-- 

*Michael "Lee" Lockwood*
michael at lockwood.us.com
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.keekles.org/pipermail/app_rpt-users/attachments/20170809/ac53840f/attachment.html>